similar to: mISDN + chan_misdn.so + winbond issue

HI: Is there any way to raise up sound volume on fxo on TDM04B without changing tx-gain and rx-gain ? __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

So far i've grasped that to use a card in NT mode it should have layermask=3 as module option. Is it the only thing that sets TE or NT mode for card? Perhaps there are settings in misdn.conf ? I can only get the card to work in TE mode and even then when asterisk is ran as asterisk -vvvgc it exits right after chan_misdn is loaded with theese messages: [chan_misdn.so] => (Channel driver

Has anyone got chan_misdn working with passive BRI cards yet? I've tried both hfc (hfcpci.ko) and w6692 (w6692pci.ko) cards, but when I start asterisk I get the following when chan_misdn is loaded: [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found == Registered channel type 'mISDN' (This driver enables the

Could someone please comment on the current state of chan_capi, chan_misdn and chan_modem channel drivers in terms of functionality and stability. Specifically, which channel driver would be best for a passive PCI HFC or W6692 ISDN card. The chan_misdn wiki claims that chan_capi distinguishes between junghanns and non-junghans cards, and that chan_misdn is better suited for general misdn

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

Hello It is all very confusing due to little information available :) I have a w6692 PCI card, so 1) What ports or modes i can use it? Currently i am plugged into a T0 port, can it be used? And what's the difference from S0? Please point me to some reading full of clues. 2) Due to lack of my understanding of the modes i can't seem to get the right protocol and layermask values for

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

hi i am experiencing some problems with the configuration of an BN8S0 Beronet card. I've downloaded last CVS of mISDN ans mISDNuser, i patch the kernel 2.6.16.18 and the enabled the following: <*> ISDN support x x Old ISDN4Linux ---> x x --- CAPI subsystem x x <M> CAPI2.0 support x x [*] Verbose reason code reporting (kernel size +=7K) x x [*]

Hi all, I've been having problems with my A20002D lately - callers from the PSTN don't hear me when I answer, but I hear them. Disabling echo cancellation in zapata.conf brings the audio (and echo) back. This used to work fine, until two days ago. The only weird thing in the logs is this: May 12 07:42:53 steerpike wan_ecd: wp1ec: The H100 slave has lost its framing on the bus! May

I may have found a source of an A-Ticked HFC 4BRI PCI adapter in Australia, and will be testing one next week if all goes well. I don't want to post the details of the reseller online unless invited to do so, so if nobody replies and says they are interested then I won't :) I'll follow up once I've tested it. Let me know if you want the details. James

Hi, Looking for a driver/s for Winbond W83792AG Or a how2 for CentOS. TIA Gerald -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.

Hello, list a have a problem i can start asterisk, i get the fowlling error: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Feb 11 13:50:36 NOTICE[2535]: chan_capi.c:2636 load_module: CAPI not installed! Feb 11 13:50:36 WARNING[2535]: loader.c:345 ast_load_resource: chan_capi.so: load_module failed, returning -1 Feb 11 13:50:36

Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all

Dear All, I am using Asterisk CVS-HEAD-05/05/05-15:46:09, and found it using up 99% of cpu 6-8 times in a day, even when its doing nothing or even if it is, its not supposed to eat all the cpu. whenever this happens, I need to stop it by issueing "stop now" 15-20 times on CLI or kill the process, then start over. Please suggest what to do. regards, Umair bari

Hi i am experiencing some problem with asterisk and misdn i've patched and recompiled the 2.6.15.5 kernel on the server i use a BN8S0 card with alla channels in TE mode. i can load hfcmulti and mISDN_dsp i load this with: /sbin/modprobe hfcmulti layermask=0xf protocol=0x22 type=0x08 and then /sbin/modprobe mISDN_dsp dmesg returns me the following: Modular ISDN Stack core $Revision: 1.34

hello, i have a problem on started asterisk, when try to start asterisk a get the fowlling error: chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) Feb 17 11:34:01 WARNING[3104]: config_old.c:27 ast_load: ast_load is deprecated, use ast_config_load instead! == Parsing '/etc/asterisk/misdn.conf': Found Feb 17 11:34:01 WARNING[3104]: config_old.c:39 ast_destroy: ast_destroy

Hi All, I'm trying to use a HFC chip ISDN modem with mISDN and chan_misdn. The card is configured to NT, PmP mode. One Siemens ISDN phone connected to the modem. When I call the ISDN phone is called everything is just fine, but when I call from the ISDN phone I face some problems. - There is no dial tone when I pick up the handset. - I call a number but there is no ringtone and after I

I have a ISDN BRI card with hisax module (w6692) and there is a lot of echo when I make calls to outside. Between the sip softphones the echo doesn't exist, but when I call to outside through the ISDN the echo exist. Is there any sense to put echocancellation in modem.conf ? ___________________________________________________ Nueva tecnología de Yahoo! Búsquedas ¿te atreves a comparar?

Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for