similar to: Outgoing TDM400P FXO calls always answered

Howdy, 1 x TDM400P card with 1 x fxo module. 1 x BT Pots line. Location - UK Calls work fine outbound but i'm unable to pickup the inbound calls. Asterisk debug: Asterisk -vvvvvvvvvvcg *CLI> -- Starting simple switch on 'Zap/1-1' -- Executing Wait("Zap/1-1", "1") in new stack -- Executing Answer("Zap/1-1", "") in new stack

I have an eight channel fxo setup (2 TDM400P cards) and I have them setup. Here are my configs: Zaptel.conf: fxsks=1-8 loadzone=us defaultzone=us Zapata.conf: [trunkgroups] [channels] musiconhold=default rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callerid=xxxxxx callwaiting=yes busydetect=no callprogress=no usecallingpres=yes callwaitingcallerid=yes

Hi Guys, I recently got a TDM400P 4 FXO for use in the UK, this at the time seemed like a good idea as I had good results with an X100P clone. Installation went great and call clarity is excellent no echo like I had on the clone card. My problems start with detecting hanging up the line. If a person calls into the system and speaks to me on a SIP phone when I hang up the call clears

Hello, I've got an Asterisk server with a TDM400P with 2 FXO modules and 2 FXS modules. This server is connected to 2 PSTN lines and 2 analog phones. In my Zaptel configuration, I've defined 2 groups : one for the 2 FXO's and one for the 2 FXS. The asterisk server is just used to add a little IVR and Voicemail service. Eveything works fine, but sometimes the conversation is

Hello, I have a TDM400P with 4 FXO ports, currently using three. When sending or receiving calls on this card, there is a nearly constant popping/clicking sound, it is related to the echo cancellation?. I adjusted my gains properly, but to no avail. I even found that setting echotraining=no in zapata.conf didn't change the scenario at all. I've plugged analog handsets into the

Location = US asterisk/zaptel from CVS. Updated last week some time. Currently rebuilding with todays checkout. I have 2 fxo channels hooked up to outside standard Bell South phone lines. If I configure as so [channels] context=pstn group = 1 signalling = fxs_ks callprogress = yes channel => 4,3 Then any call routed from asterisk to the outside line will ring, and can be picked up, but *

Hello, I have recently purchased a TDM400P card with one FXO expansion card, and I'm having problems. The card does not pick up incoming calls. Asterisk detects the ringing line and rings various SIP phones as required. When a sip phone answers, the sip user hears nothing and the PSTN user continues to hear ringing. Here is the asterisk output for an incoming call:

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

I have been having some troubles with the zaptel channel on what appears to be the inbound process. The box is running the stable CVS code and has a TDM400P 4-port FXO card in it for analog connectivity. Channel 1 is the only active port on the card at the moment as we only have one analog line. What has been happening is that it looks like Asterisk has been detecting an inbound call even though

Hi all, I can't figure out why my TDM400P (with one FXO plugin) won't answer any calls. There are no messages in the Asterisk console when a call is placed to the FXO line from the PSTN. Any suggestions would be most appreciated. The wctdm and zaptel modules are loaded: [root@steerpike asterisk]# lsmod | grep wc wctdm 37952 0 zaptel 189700 1 wctdm

Ok, I just got my 8 channel setup to dial out and back in but here is the new issue. It sill dials in fine with all the channels, but dialing out from inside the asterisk system only works on the 1st channel of my 1st TDM400P card. Now I dont have all 8 PSTN lines going into my asterisk box at this moment, only one line for testing currently, but I should be able to plug that one line into any

Thanks for the suggestion. I have busydetect=yes in zapata.conf. You refer to "Martin's algorithm". Can you provide more details please? ----- Original Message ----- From: "Soner Tari" <list@kulustur.org> Subject: Re: [Asterisk-Users] FXO module in TDM400P (UK, BT) - Hangup detection failing To: "Asterisk Users Mailing List - Non-Commercial Discussion"

Hello all! I have tried and tried to resolve this one to no avail. Hopefully one of you can help... The system in question is a Compaq Evo D600 (iirc) business desktop, with a 1.4GHz Pentium 4 and 512mb of RAM, running a stock install of PoundKey 1.2. It has two Digium cards installed: a TDM400P with four FXO modules, and a TE110P hooked to a Carrier Access Adit 600 which serves 8

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi all, I have hit a wall configuring a TDM400, I have set these up before without issue but today I just can't seem to figure out what I am doing wrong. On an incoming call the following is produced in the Asterisk console with verbose 4 -- Starting simple switch on 'Zap/2-1' Mar 22 16:12:34 NOTICE[2051]: chan_zap.c:6063 ss_thread: Got event 18 (Ring Begin)... Mar 22

I'm a bit confused on how to setup Zaptel.conf and Zapata.conf when there is a TDM400P and a TE410P installed after upgrade. The TDM400P has 2 FXS in position 1 & 2 and 1 FXO in the fourth position. I see boot, WCT4xxP loading first and WCFXS loading second. According to my understanding, given above, the TE410P should be configured first, then the TDM400P. However, I'm not sure

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

I have 2 Digium 4 port FXO cards in my system. The system is a P4 2.4Ghz, 512MB RAM, Promise FastTrax 100 TX2 Pro Raid, 80GB RAID1 for storage - whitebox - running RedHat 9. With pretty much any CVS HEAD version we are getting, what I will call, "phantom" calls on some lines. What I mean by a phantom call is that the line will ring, Asterisk will log that the Zap channel has been

I'm having real problems with my connection to BT, it is a home line, but after a while it sets an alarm and only a restart of asterisk resets it could some one look at the below configs and suggest any changes to make this more reliable Thanks for your help Robb asterisk version 1.6.1.10 dahdi version SVN-trunk-r7445 dahdi_scan active=yes alarms=OK description=Wildcard TDM400P REV I

Hi, I have configured tdm400p alone and it works fine for me. But now i tried to add 2 x100p in the same machine with the following configs, but asterisk refuses to load, can someone guide me what i have done wrong. Following r the configs and output. TIA, Azher >> ./asterisk -vvvvvc [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --