similar to: Setting up a TDM

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

I'm a bit confused on how to setup Zaptel.conf and Zapata.conf when there is a TDM400P and a TE410P installed after upgrade. The TDM400P has 2 FXS in position 1 & 2 and 1 FXO in the fourth position. I see boot, WCT4xxP loading first and WCFXS loading second. According to my understanding, given above, the TE410P should be configured first, then the TDM400P. However, I'm not sure

Hello Since TDM cards are known for being particular when it comes to motherboards (PCI 2.2, etc.), I was wondering if there is a utility that can check that the Zaptel driver works OK and can tell if the TDM card is compatible? That way, if an FXO module is not reporting an incoming call, we'd know it's because of the Zaptel driver, and not something elsewhere. Are "dmesg",

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

How does TDM work, how do you connect to it? I have the impression it can't be routed like ethernet, but a cable from your switch has to be plugged into the providers equipment. I have seen the Asterisk info about TDMoE - does this mean that the Asterisk card will modulate the signal on the Ethernet cable to allow it plug directly into a proper TDM connection? Will someone please enlighten

Over the last week we've been having issues on our Telco provided TDM T1 with the circuit bouncing for several seconds and restoring itself back into service. The T1 is using a TE410P. On the CLI, I see message that span 1 is yellow alarm, then restoring. I reported this problem to the phone company. Afterwards, they do several circuit tests to the NIU and then to the CSU. At the point

I sent a query about this before, but have some further information and am hoping somebody has a suggestion as to what to try next to debug this. I'm using an Asterisk box primarily for MeetMe conferencing. There are two sources: TDM via two Q.SIG T1's and SIP phones. Conferencing works fine between TDM channels. But when a SIP phone calls the conference, there's no voice path *to*

Hello all, I have a WildCard TE410P setup and working with a full PRI with the latest CVS. SIP and IAX2 gateways are accessing the PRI without issue, however; echo is very prominent in some calls and is only heard by the IAX2/SIP client. The echo Is not present in calls to cell phones because they are digital, centrex land Lines have a barely noticable echo, but analog lines aint so pretty.

I just installed an FXS module onto a 4 channel tdm thats about 5 years old and it wont work. Running dmesg I can see the following error: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should

Hello All, I have a Digium Wildcard TE410P Quad-Span T1 Card, when I do connect T1 lines it goes in RED. When I do connect the same line on a different Server (Same Model T1 Card) it works fine. How do I examine/diagnose my T1 Card for any hardware failures. I heard about loopback test , how helpful it is? Here are my configuration /etc/zaptel.conf span=1,1,0,esf,b8zs

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

I am having to abandon asterisk after having used it for 2.5 years due to this problem. Every couple of days (sometimes more often, sometimes less), the machine will lock up because the TDM board or the Dahdi driver goes south. /var/log/messages starts filling up with repeated messages: kernel: TDM PCI Master abort The card I have is: *CLI> dahdi show status Description

Hi On an old IBM Netvista thinclient, the TDM card doesn't detect incoming calls, although the card seems to be detected, and correctly configured: pbx asterisk # lspci 00:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface # cat /etc/zaptel.conf fxsks=1 loadzone=fr defaultzone=fr # ztcfg -vv Zaptel Configuration ====================== Channel map: Channel

The quick question: Do the digium drivers for the Digium Wildcard TE410P (4 port T1/E1/PRI 3.3v card) , the T100P (single port T1), and the TDM400P support hot plug PCI? I am also noting that while the TDM400P doesn't state the voltage requirements, it looks like a 5v card. I hope that I am wrong on this. What type of T1 channel bank would people recoment for ISDN (for video

Hi I'm new in this field, have been reading a lot, and have a little question. could it be possible to connect an Avaya IP office pbx to asterisk using a E1/T1/Pri? Original instalation: Telefone company|Pri--->Pri|IP Pffice My Question: Telefone company|Pri --->TDM|Asterisk|TDM --->Pri|IP Office I know that it can be done by using h323, but I need a card on the IPOffice my

Dear All, How can we know the On board supports echo cancellation I have *Digium, Inc. Wildcard TE410P quad-span T1/E1/J1 card 3.3V (rev 02)*board all working fine but sometimes i got echo when user are calling a PRI. is there any way to know on board echo cancellation . regards Dhaval -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, what new Dell servers are compatible and KNOWN to work with Digium TDM cards? I've looked at Digium's compatibility list at http://www.digium.com/index.php?menu=compatibility. Does this mean that other Dell servers like SC1420, SC1425, 800, 1800 are working just fine with TDM cards? Can someone clarify this? Thanks -David