similar to: Digium Wildcard X100P Error

I have recently upgraded my firmware from v6.3 to v7.4. Now when the phone is booted or rebooted, the initial screen "Initializing Vlan" takes forever to initialize before it initializes IP. Any ideas/Thoughts? (Trying not to Revert back to v6.3). -C -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All, I have the problem setting up TDM22B card. Steps what I have followed are: [1] compiled zaptel-1.0.9.2 & installed the same. [2] modprobe wcfxo /lib/modules/2.4.20-8/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

Hi, I've successfully installed Asterisk 1.0 on Fedora Core 2 with the 2.6.8 kernel. I have two other computers running X-lite connecting to it. I've been able to set them up so I can dial extensions "123" and "124" to talk between them. I'm able to access the default "1000", "500", and "600" extensions and they all seem to work.

I finally got Solaris to successfully make asterisk, using these instructions: http://sunfreeware.com/programlistsparc10.html#gcc33 Now though, when I issue the make install, I get this error: mkdir -p /var/opt/asterisk/spool/system mkdir -p /var/opt/asterisk/spool/tmp mkdir -p /var/opt/asterisk/spool/meetme install -m 755 asterisk /opt/asterisk/usr/sbin/ install: asterisk was not found

Hello, it is now 2am presently where i am and i have been at work since 8am yesterday. I am not allowed to go home unless i get this system up and running, else i shouldnt expect a job when i come back :s... now that you have some background, I am having no luck installing these two cards - i have already confirmed they are on their own IRQ etc, and if i run genzaptelconf, they are coming up

Was in the process of upgrading a 7960 to SIP and in advertently applied a skinny image (P003G302.bin), now no matter what i put in OS79XX.TXT and OS7960.TXT it simply wont upgrade. The phone is pulling down OS79XX.TXT from my TFTP server but then goes on to repetedly ask for SEP<MACaddr>.cnf. Help!! -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I recently decided to change my setup from AsteriskNow to plain-asterisk 1.4, which I wanted to set up and configure myself on a server running Debian Etch 64bit version. Hardware: Asrock motherboard, model 775Dual880-Pro, with a Celeron D running at 2.8GHz, 1GB memory, standard Nvidia GF4MX videocard, and one X100P clone card. Running the AsteriskNow, everything worked fine, except for

Hi Version 0.9.0 of Xorcom Rapid Debian/GNU/Linux/Asterisk has just been released. Main changes: * A decent version of Asterisk/Zaptel (1.0.2) is provided * Includes a better default configuration * Automatic detection of the most common Zaptel cards * Contains more optional software (apache, MySQL, Webmin and others) - available via menu You can get it from:

Hi, I know we've talked about this phone to death. I have pretty good voice quality, with and without WEP enabled, using the G729a codec and DLink & Netgear access points. I am facing one obstacle that is driving me insane. Does anyone have the call hold feature working? If you do... how did you make it work? The instructions say to press the left button to place the call on hold,

hi every body; i installed zaptel 1.4,libpri 1.4, asterisk 1.4, asterisk-addons 1.4 succefuly, but i can't find the command "genzaptelconf, so i tink to install "handy zaptel toolset" please can someone tell me whitch package goes with zaptel 1.4, i consult "http://updates.xorcom.com/rapid/pool/main/z/zaptel/" but ????????????

I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed. But still problems: Here is my ztcfg output: asterisk:/etc/asterisk # ztcfg -vvvvv Notice: Configuration file is /etc/zaptel.conf line 4: Unable to read Zaptel version information. Zaptel

This is a new installation. Here are the specs of my system: Linux asterisk 2.6.21.5-smp #2 SMP Tue Jun 19 14:58:11 CDT 2007 i686 Intel(R) Xeon(R) CPU E5420 @ 2.50GHz GenuineIntel GNU/Linux 08:08.0 Ethernet controller: Digium, Inc. Unknown device 8000 (rev 11) (ethernet?? first time with a card like that for me) dmesg Zapata Telephony Interface Registered on major 196 Zaptel Version:

Helo, I have problem with Digium TE110P connected to CISCO 3640 (port on NM-HDV-2E1-60) wth PRI E1 link. I use CISCO now for testing but when I tried with real PBX problem was exactly same. I have this messages in Asterisk conole and log sometimes: NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Usually 2-5 such messages in series, can be repeated after 10

Hi, I have installed Asterisk 1.4.20 on Debian Etch. The server has no telephony card installed, but I have anyhow installed Zaptel (Zaptel-1.4.9) in order to be able to use MeetMe. The Zaptel modules load normally. I obtain the following prompts: kerplunk:/# /etc/init.d/zaptel start Loading zaptel framework: done. Waiting for zap to come online...OK Loading zaptel hardware modules: ztdummy.

Greetings to all list members! My name is Aldo Sudak and I am an Asterisk newbie. I am writing now because I have not been able to find any mention to the issues described below, neither in this list nor in the wiki. I am performing preliminary tests with Asterisk 1.4.11 and Zaptel 1.4.5.1 on Fedora Core 6. Installation of all of the Asterisk packages was straightforward and I always obtained

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

Hello, I recently purchased a Wildcard X100P FXO Card primarily as a learning tool and to provide myself with voicemail and a few other perks that are better than an answering machine. I followed the setup in the FAQ, and it works, just not well. The sound is very choppy and staticy whenever a call is placed. Sometimes it clears up, and sometimes it degrades very badly. I also recently

Hi all, The Wildcard X100P card or the Asterisk Developer's Kit (LITE) are available somewhere in Europe or must be ordered in US? Thanks, Dan

On Fri, 8 Aug 2003, Dave Cotton wrote: > The x100p does get the CID in France. It is now a question of how to break it down. > > I changed callerid.c line 278 to :- > > ast_log(LOG_NOTICE, "Got this:- %s\n", cid->rawdata); > > and the result on August 8 at 10:06 from 0490233081 was:- > > File callerid.c, Line 278 (callerid_feed): Got this:-