similar to: Known Working Motherboard/CPU for TE410P

I am having a problem with asterisk not being stable enough for production use. I have two cards, the digium TE406P, and the TE410P. The TE410P is the primary card that I am using but I would like to move to the TE406P for the echo cancellation and more flexibility of PCI slots available. General config info: 3 PRIs, configured as such: span=1,2,0,esf,b8zs span=2,0,0,esf,b8zs

Hi all, I'm looking for a new system which will use the TE410P. Originally I was going to use a dual Athlon MP system, but my supplier tells me these are being phased out now, and so will be difficult to find replacement parts later. So, I am looking for suggestions of suitable motherboards with 3.3V PCI slots for the following CPU types (in order of my personal preference) AMD Opteron 1xx

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Hi- I have posted a photo of the TE410P Digium card on my site, so that those wishing to purchase a compatible motherboard can see physically what the PCI slot requirement is: http://www.evtmedia.com/TE410P.htm I believe the required slot is a 64-bit, 3.3 Volt PCI, most commonly found on Xeon-based motherboards. A 64-bit slot is longer than the TE410P board requires, but the PCI connector

Can anybody tell me the difference between a TE410P and a TE405P? Is it JUST the 5v vs 3.3v pcis slot spec, or is there some thing else? </edg>

Hi to all out there using HP DL380 G4 servers, i found a way to get the Digium TE410P with older firmware running on a HP-Compaq DL380 G4 Server! Here's the step-by-step description: 1. download the latest BIOS (in my case it was 4.04 from date: 06/02/2005) for the HP-Compaq DL380 G4 using the "Systems ROMPaq Firmware Upgrade Diskette for HP ProLiant DL480 G4 (P51) Servers" Link:

hi all, i am trying to get my TE410P (see previous posts) working in Austria (telekom Austria - i am still waiting for an answer for my questions). my /etc/zaptel.conf looks like -------------------------------- span=1,1,0,ccs,hdb3,crc4,yellow span=2,2,0,ccs,hdb3,crc4,yellow bchan=1-15,17-31 dchan=16 bchan=32-46,48-62 dchan=47 loadzone=at defaultzone=at -------------------------------- after

I have a TE410P running on CentOS 4 which (fortunately) is my test system. This card has been working flawlessly for the past few weeks. Today I did a cvs update to the latest head files, and the card is now not working. When I try a zaptel start, a series of messages appears on the console: Found TE410p at base address fdff0000, remapped to f8a34000 TE410P version c01a010b, burst ON, slip

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

TE410P - one way audio, after "rpm -qa" on RedHat 9 After much trouble, I can consistently reproduce this error. Anyone have any idea why all Zap channels on my TE410P would develop one way audio after "rpm -qa" has been run while asterisk is running? If I reboot, run "rpm -qa" first then load asterisk and modules all is OK when "rpm -qa" runs the second

Has anyone else experienced a problem with the LED for span 1 on a TE410P or TE405P? I had a TE410P on which the span 1 LED would not light red, but once the span was connected, it did correctly light green. I RMAed the board to our UK distrbutor and received a replacement. However, the replacement board displayed the same problem! Wondering if it was related to the computer I was putting it

Hey there, What recommendations does anybody have as to motherboards known to work well with the Digium TE110P T1 interface cards and the TDM400P analog POTS interface cards? We currently make use of the TE110P for our T1 (esf w/ b8zs - not a PRI) and have experienced many issues caused by our PBX's motherboard. Additionally, we built a server to become our new PBX, but that machine runs

I've just encountered an odd problem with our Digium TE410P card and was wondering if anyone has experienced something similar before. We utilize all 4 ports with 2 of them connected to the PSTN as E1 with the second 2 ports connecting to a device which accepts T1. We are essentially acting as an E1 to T1 converter. This machine has been operational for close to 6 months without a problem.

Was there any resolution on this I also have a TE410P in an box with an Intel E7501 chipset? -Vickers -------- Original Message -------- Subject: RE: [Asterisk-Users] Re: TE410P card in an HP-Compaq DL380 G4 server Date: Tue, 8 Feb 2005 11:13:24 +1030 From: Peter Childs <peter.childs@nec.com.au> Reply-To: Asterisk Users Mailing List - Non-Commercial Discussion

I for one think it is a great idea to buy a book with hard earned money and wait a few days to a week just to get an answer to a question that is freely available on the internet immediately. Hard pressed to think of anything in the "book" that is not on with wiki with more up to date and useful information. -----Original Message----- From: Alexander Lopez

Max TE410P card on an Asterisk Hello, Does anybody know the max number of TE410P/TE405P card we can put in an asterisk box? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040504/f220d3ae/attachment.htm

hi guys, do you have any suggestions on how to connect 2 TE410P via E1? (for simulation and testing purposes) asterisk1 --> TE410P ----> ? ---------> ? ---->TE410P -->asterisk2 -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030907/698cd499/attachment.htm

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040809/8f53bb6a/attachment.htm -------------- next part -------------- ? Hi There, We install asterisk in RH9. We've T1 line and four TE410P card. We wanted to configure this card. We used ztcfg to see the channel configuration. It shows like "Channels 0". How to configure

Anyone ever experience noise instead of a dial tone. We are using a Digium TE410P and 2 units of Rhino FXO & FXS Channel Bank. Everything works well when they are freshly turned on or rebooted, but after a while there's only noise can be heard instead of dial tone. Does this have anything to do with the timing configuration? Where is this time is generated from, is it from the TE410P card?

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards