similar to: Zaptel problems on Debian

I have a couple of questions about Digium's T1 cards, such as the TE410P. Any answers would be greatly appreciated. 1) Do they support standard T1s or are they ISDN-only? 2) Do you know of anyone offering support for configuring T1s for Digium cards, and if so at what cost? Thanks, Matthew Roth http://www.voip-info.org/tiki-index.php?page=Running%20Asterisk%20on%20Debian

Hi List, After reading a bunch of the docs, list post archives, it still seems that a clear definition of how to clock the T100P card is muddy. zttool says that the link is "INTERNALLY CLOCKED", does this mean the T100P is providing clock, or does this mean the T100P is getting clock from the T1 line side (ergo getting clock from the Telco) ?? If you have sync = 0 then zttool

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

Basically, have an old IVR application running under Apex's Omnivox software on a box with 4 old intel dialogic D240SCs, and would like to allow remote clients to gain access to aforementioned IVR application via softphone, 7960, ata, etc via asterisk with a TE410P. Unfortunately, all I know about the dialogics is that they're configured for D4/AMI, which I believe I have configured right

First of all - Many, many thanks to Mark for his troubleshooting and fix of bug 1320 (FXO_KS signalled Zap Channels on Adtran 750 Channel Bank Stuck in Rsrvd State). I have heard complaints that once every couple weeks, when a user picks up their analog phone (t1 span off of a TE410P into an Adtran 750 with 6 FXS cards), they don't get dialtone, but instead, hear another conversation.

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

I am looking for estimated hardware requirements for running a 50 to 100 seat call center off of a single Asterisk server. The Asterisk server will have one quad T1 card installed (probably a Digium TE410P) with two T1s connected. The OS is Debian GNU/Linux (woody) with a custom 2.4.xx kernel installed. It is preferable for the server to have a single CPU and no shared IRQs. I would really

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

Hello, I am missing any description of zaptel/DAHDI alarms. The TE200 series user manual contains only a description of LEDs states. These alarms states are visible in zttool/dahditool or in astersick CLI (zap show status) and I wonder what is the real meaning of these alarms for E1 channel. Possible alarm states (based on zaptel.h 1.2): 1. No alarms 2. Recovering from alarm 3. In loopback

I have a TE405/TE410P card that was working on 1.0.X I upgraded the OS to Centos 4.5, Updated asterisk to 1.4 and zaptel to 1.4.5 and libpri. I copied all the zaptel and zapata and extensions.conf files from 1.0 I did update extensions.conf from 1.0 to 1.4 commands. I cannot get the card to work in 1.4.10. AHHH! I see with zttool that the T1 is in Green, I see calls coming in as the bits go

I've been running Asterisk for months with no problems. I have grown to the point where I need an aditional TE cards. After many attempts I was able to add the second card without affecting the performance of the first. However, the second card is not working properly. Setup ===== - Running on a Dell Server. - RedHat 8 - Asterisk 1.0 - I have two TE410Ps on that box, card 0 assigned to

Hello everyone, I'm using a TE410P, no irq sharing, and all extraneous devices disabled, such as USB, Parallel etc. I'm getting a few IRQ misses according to ZTTOOL. We're running a standard PRI_CPE interface and seem to be getting dropped calls, and errors on the D-CHANNEL occasionally. The circuit itself is very solid, it was in use on our old PBX just a few weeks ago, never

Hi, I am having some problems mentioned below, the box is in production live environment with traffic around 30 - 100 calls. I am running T/E410P in a Dual P4 xeon with HT disabled. I am using zaptel 0.9.0 and asterisk stable 1 release. There is no gui, just mysql, perl (small script) and asterisk. System runs very smoothly if the calls are around 40-50 and comes one by one , however sometimes

Hi, I'm trying to connect a PC with a TE410P to an E1/IP equipment. Unfortunately I keep getting a yellow alarm from zaptel (in zttool) and a Loss of Framing alarm on the remote equipment. The E1/IP is connected on the other side to a PRI interface on a GSM MSC. I have configured the span as: span=1,1,0,ccs,hdb3 (also tried span=1,0,0,ccs,hdb3) and the channels as: bchan=1-15,17-31

I have 12 T1's going into 3 servers, 4 in each into "Digium, Inc. Wildcard TE410P Quad-Span togglable E1/T1/J1 card 3.3v (rev 02)" cards. Each "group" of T1's have the primary D on 24 and the secondary D on 96. The first server (ts20) and the last server (ts22) can playback "demo-congrats" fine. The "middle" server (ts21) cannot -- just dead air.

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040810/16371a21/attachment.htm -------------- next part -------------- ? Hi, I'm using TE410P card with four T1 lines. I've configured all the channels in my /etc/zaptel.conf file. In zttool i'm getting "OK" for the "Span-1" but the other three spans giving

Hi all, The last e-mails about beginners gave me the courage to post a question; from a beginner's perspective, there are a lot of questions that I'm tempted to ask. But I'm trying to find the answers either in the documentation, either in the about 15 free books I have, either in the help archives (I often found many similar questions posted in the past). Being an (still actual)

Dear List i have upgrade my * box with the latest CVS version of Asterisk Stable 1.0 and zaptel/libpri my system is MDK9.2 with 1 TE410P and seems work well for now but i have a little amount of traffic (25 IN/OUT calls) i only notice this Warning.. What kind of error is? ------------------------------- Apr 20 21:28:49 WARNING[147466]: chan_zap.c:5979 zt_pri_error: PRI: !! Got reject for

Hi all, I have a box running asterisk with T410 connected to a Nortel DMS 100 switch and another box running SER with grandstream phones on it So if there is a call from the pstn it goes from the Nortel to the asterisk and then to the SER box and finally to the phones.if the phone is busy or the number is invalid the * box will first send an ALERT message to the Nortel and say the call is going on