similar to: Wildcard TE110p initial setup

I need some help getting a system running for one of my company's plants. I am running AsteriskNow 1.7 with Asterisk 1.6.2.10 and FreePBX 2.8.0.2. My D-Channel keeps bouncing. The telecom tech told me he thought that I might be using the wrong sync source, and I think I might have been, but I changed DAHDI system.conf to "span=1,1,0,ESF,B8ZS" (from

I have what my SBC/ATT representative calls a "Supertrunk," but he can't tell me the specifics I need to know to configure Asterisk to work with it. By fiddling about, I've come up with the "almost working" configuration below. This works except that it takes about 4 seconds from when the console says the line is answered until it plays my prompt. Watching the

Hi, I have problem with X100P clone card.I can not force it to work under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2. I looked over and over on configuration and could not see any mistakes. Here are relevant configuration files. /etc/dahdi/system.conf > fxsks=1 > echocanceller=mg2,1 > loadzone = hu > defaultzone = hu > dahdi_tool > OK Wildcard X100P

Hi Group, I have a problem with my FXO interface. It seems that asterisk cannot see any configured channels, only pseudo. Pls see the error and my config below. Rgrds Markus ----- May 2 15:09:00 NOTICE[17327]: app_dial.c:1010 dial_exec_full: Unable to create channel of type 'Zap' (cause 0 - Unknown) == Everyone is busy/congested at this time (1:0/0/1) == Auto fallthrough, channel

> I've never bothered to check to see if cat5 cables use the appropriate > mating twisted pairs or not. Since the pinouts are different for cat5 vs > T1 cables, I'd have to guess a single strand is used from two different > twisted pair groups. That wouldn't be cool, but in short runs it > probably doesn't have much of an impact. > IIRC, standard Ethernet uses

Hi, I've been playing with a TE120P on Asterisk 1.4.18 with zaptel 1.4.9 and I've ran into an issue. After a call placed any DTMF tone causes the server to lock up entirely. Calls placed work just fine (except for a problem with echo cancellation). The phone registered to the server is a Linksys SPA-942. I am seeing in zttool some IRQ misses, but it never seems to go above 74 (below).

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

> Close. 10/100mbps Ethernet uses wires 1,2,3,6 but that is pair 2 & 3. > Pair > one is the pair up the dead center (pins 4&5), pair 2 is pins 1&2, pair 3 > is > 3&6 and pair 4 is 7&8. A T1 uses pairs 1&2, which is why you can't use a > regular crossover cable for a T1 crossover, but you can use a regular > ethernet patch cable as a T1 patch

Hello everyone, I bought 2 HFC-ISDN Cards and want to run the first card in NT-Mode an the second one in TE-Mode. Everything looks ok under SuSE 9.1, but I can't dial out. I removed one card, for testing purposes and want to run this one card in TE-Mode. I only want to make a call with my Grandstream BT-101 over Asterisk via ISDN. When I try to make a call I get: ---------------------

Hello, I am installing asterisk, libpri and zaptel. I have it setup for EM wink. incoming calls are working. outgoing calls are not. zttool shows TxA as 11000000 RxA shows 00000000 This doesnt seem like em_w signalling? Seems like the PBX is not setup for EM_w. Is that the case? Jerry

Hi, It seems like my ATA is making a ringing noise... (as it used to), but now (After the upgrade from 1.0.7 to 1.2) asterisk also is either making the ringing, or passing the PRI ringing from the telco on to me. Any suggestions on how to fix this?

Hello, I have an E100P, and in the zaptel.conf I have: span=1,1,0,ccs,hdb4,crc4,yellow fxsks=1-10 the light on the card is green( BTW what do all those states of the card that zttool reports YELLO, RED, BLUE ..., is there a doc for zttool?, or for the card?) in the asterisks` zapata.conf I have: [channels] context=default switchtype=euroisdn signalling=fxs_ks usecallerid=yes hidecallerid=no

Also rework things so that if someone were to add an opcode without adjusting the values in these arrays, there will be a compilation error. This fixes a few quadop-related piglit regressions since commit d5faf8e78603. Signed-off-by: Ilia Mirkin <imirkin at alum.mit.edu> --- src/gallium/drivers/nouveau/codegen/nv50_ir_target.cpp | 12 +++++++-----

Hi. I have been looking at the PCAproj function in package pcaPP (R 2.4.1) for robust principal components, and I'm trying to interpret the results. I started with a data matrix of dimensions RxC (R is the number of rows / observations, C the number of columns / variables). PCAproj returns a list of class princomp, similar to the output of the function princomp. In a case where I can

Okay, I can't find what might be causing this. Here is what I got: Asterisk server hooked up to a digital T1 line (full 24-channel) via a Digium card. Verizon has turned on caller ID on the first line (I can guarantee it is on as I can hear the FSK tones on this line but not the others). Using zttool an ZapScan() I have determined the following: 1) The RxB/RxD bits toggle from 1 to 0

Hi, I am trying to test for pairwise associations between genotypes ( Rows=individuals, Columns =genes, data are up to 4 genotypes per gene, some with 2,3 or 4) where each chisquare comparison is different depending on the genes tested. The test is the observed multilocus (across columns for each individual) genotypes vs the expectation, which is the product of the individual frequency for each

Hi All, I tried my best to figure out how to deal with the freezing R console but with no luck. I followed the instructions of calling R_ProcessEvents() regularly but still couldn't work it out (the callings were removed from the below C code). I am using R-2.8.1 on Windows XP service pack 3. The Rtools is version 2.9. I have the following C code: void rx(int *n, int *m, int *rxmax,int

Dear colleagues in R, Has anybody implemented the 1) (Goodman & Kruskal) lambda or the 2) (Thiel's) uncertainty coefficient statistics (in the asymmetric and symmetric forms), or is anyone aware that they might reside in some package? A search in the R archives does indicate that they are (somehow) part of the CoCo package, but I would rather not start learning how to transform my

I want to ascertain the basis of the table ranking, i.e. the meaning of "extreme", in Fisher's Exact Test as implemented in 'fisher.test', when applied to RxC tables which are larger than 2x2. One can summarise a strategy for the test as 1) For each table compatible with the margins of the observed table, compute the probability of this table conditional on the

Hello, My advisor and I have been working on some survivorship analyses in R and we are hoping to get some feedback on a particular issue involving nesting. We are interested in patterns of food discovery by ant species. Our observations consist of time to discovery by an ant for three different food types, each of two different sizes. These data were collected at 6 plots located in each of