similar to: Installed ztdummy, Asterisk doesnt work anymore

hi all iam using ztdummy driver after my call end , when i look at debug mode in cli i get this errors --- (0 headers 0 lines) Nat keepalive --- -- Reloading module 'chan_agent.so' (Agent Proxy Channel) == Parsing '/etc/asterisk/agents.conf': Found -- Reloading module 'chan_local.so' (Local Proxy Channel) -- Reloading module 'chan_zap.so' (Zapata

When I reload the asterisk I get the following warnings: Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring switchtype Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring signalling Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring rxwink Everything works fine as far as I know, I can dial and complete calls. So why am I getting this

When I reload the config, I see this error in the CLI. However, I don't see what I have done wrong: == Parsing '/etc/asterisk/zapata.conf': Found May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured channel 1, FXO Kewlstart signalling May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured

Good day all We got a Wildcard TE110P I installed linux,zaptel,libpti and asterisk I coped over my zaptel.conf and zapata.conf from a previous E100P config But when I try to start asterisk it gives error not bying able to load zap channles: == Parsing '/etc/asterisk/zapata.conf': Found Jan 10 08:17:18 WARNING[-1084595552]: chan_zap.c:9308 setup_zap: Ignoring switchtype Jan 10 08:17:18

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Hi all, I have a problem with the cvs head zaptel library: I cannot update my zapata.conf into asterisk when I issue the reload command from the CLI prompt; only when I stop and restart the asterisk service. The system sends the following message: Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364 setup_zap: Ignoring switchtype Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Hiya all, I have had no end of trouble trying to get my A101 E1 card working on a new asterisk installation. The sangoma tech people have ignored my emails about this. All the installation of wanpipe seems to go ok, and zaptel. it all installed compiled and does all the wanpipe hwprobe exactly as documented. Asterisk compiled ok, but when I run it give me Jun 27 11:12:18 ERROR[10528]:

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

Greetings I was getting bad static crackle on a phone, so I reload from the latest CVS and did a make clean ; make install on zaptel, libpri and asterisk Now I get this error [chan_skinny.so] => (Skinny Client Control Protocol (Skinny)) May 28 13:59:42 WARNING[16384]: chan_skinny.c:2541 reload_config: Unable to get our IP address, Skinny disabled Urgent handler [chan_oss.so] => (OSS

Anyone have any idea what this is talking about. Here is my zapata.conf [channels] switchtype=5ess signalling=pri_cpe echocancel=yes echocancelwhenbridged=yes echotraining=400 callerid=asreceived group=1 context=default musiconhold=default faxdetect=incoming channel => 1-23 Here is my zaptel.conf span=1,1,0,esf,b8zs bchan=1-23 # set this to 1-15,17-31 for E1 dchan=24 # set this to 16 for

Hello list , I?m putting to work a new asterisk box. I?m running * 1.0.3 with (one ) Wildcard TDM ( 2FXS* 2FXO) and (one) E-100P. Both boards are working well. ztcfg don?t show me any error. zttool list both cards as "OK" But when i run asterisk on verbose mode i get those errors : [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --

Hello all I just checked out the latest zaptel/zapata/libpri/asterisk/asterisk-addons from the cvs and ran through the entire make procedures. Everything seemed to go fine however now when I attempt to start asterisk, it says ok but it seems to be immediately crashing. The following messages are displayed in my /var/log/asterisk/messages file for the time right around the crash: Dec 29

I have configured /etc/asterisk/zapata.conf, but now Asterisk refuses to start: Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:5976 mkintf: Unable to get parameters Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:9478 setup_zap: Unable to register channel '1-15' Aug 5 10:47:29 WARNING[1076842624]: loader.c:328 ast_load_resource: chan_zap.so: load_module failed, returning -1 == Unregistered

Hello, I am trying to REGISTER asterisk to a SIP server, which is listening on Port 6060 (not 5060). The sip.conf file contains register=18474201111:quintum@192.168.2.94:6060/18474201111 maxexpirey=3600 defaultexpirey=120 But the REGISTER message is sent to Port 6060, but the Request-URI still contains, 5060. This is being rejected by SIP server. REGISTER sip:192.168.2.94

Hi all, We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap modprobe wcfsx then the ztcfg output this: Zaptel

After emerging some updates this morning asterisk 1.0.3 fails to start I get the following errors: ..Jan 6 00:39:24 WARNING[28998]: chan_zap.c:765 zt_open: Unable to specify channel 1: No such device or address Jan 6 00:39:24 ERROR[28998]: chan_zap.c:6197 mkintf: Unable to open channel 1: No such device or address here = 0, tmp->channel = 1, channel = 1 Jan 6 00:39:24 ERROR[28998]:

Hello, This is debug output I get: Jul 28 15:05:49 WARNING[8249]: chan_oss.c:239 sound_thread: Read error on sound device: Resource temporarily unavailable [chan_zap.so] => (Zapata Telephony w/PRI) Jul 28 15:05:49 WARNING[8249]: chan_zap.c:924 zt_open: Unable to specify channel 1: No such device or address Jul 28 15:05:49 ERROR[8249]: chan_zap.c:6460 mkintf: Unable to open

Hi, I have two WCT100P cards installed on a suse 9.0 box. Installation for Zaptel complains of some unresolved dependencies. The zaptel and wct1xxp modules load without any errors. ztcfg give no problems. The problem is when I start asterisk I get the following error and asterisk shuts down

Hi, all I have installed TDM400 card. I can see it is there (lspci). But Asterisk does not find it. phonebox2*CLI> zap show status No Zaptel interface found. I assume that driver is not loaded, but I am sure I have installed it (I compiled zaptel and then re-build asterisk and did make install for both zaptel and asterisk). When asterisk is started I get: Jan 2 06:28:08 WARNING[3473]: