similar to: Manual Paritioning with fdisk

When a new system CentOS-4.4 is built the swap partition is always reversed... Note md3 below, the raidtab is OK, I have tried various raid commands to correct. swapoff -a raidstop /dev/md3 mkraid /dev/md3 --really-force swapon -a And then I get a proper ourput for /proc/mdstat, but when I reboot /proc/mdstat again reads as below, with md3 [0] [1] reversed. [root]# cat /proc/mdstat

Hi, I have a system with two IDE controllers running RAID1. As a test I powered down, removed one drive (hdc), and powered back up. System came up fine, so powered down installed a new drive (hdc) And powered back up. /proc/mdstat indicatd RAID1 active with hda only. I thought it would Auto add the new hdc drive... Also when I removed the new drive and added The original hdc, the swap partitions

Dear Asterisk users, We would like to announce that Druid, Open Source Unified Communications project has just made a major release: Druid 2.0. It is out!It has a ton of new features and a highly improved interface. Asterisk stability has also been greatly improved. For more info http://forums.voiceroute.org/showthread.php?t=837 Some of the key features - Improved Web GUI, faster and smoother -

I was searching thru the internet and I found a wide variety of different web interfaces for asterisks I was curious which one is best suited for asterisks. Thanks

I have recently noticed that druid @ http://www.voiceroute.org has created an open source edition of their platform. I downloaded it today and installed it on a play system where I have about 20 ip phones ranging from cisco, polycom and aastra phones. I didn't even have to configure them as the system automatically did it for me. I have been using trixbox/freepbx combination for over that last

Is it possible to partition a disk with Disk Druid and control the order of the partitions? I want to create my own boot and swap as RAID partitions but Disk Druid won't keep them in the order I want, no matter what I specify first. I've done this before by using fdisk to make the partitions before starting Disk Druid but I thought someone said this was an old bug and should have been

Hello, I have installed centos using automatic partition. I would like to partition my hard disk to /, /var/, /usr, /home separately. Is it possible now to partition post installation. I also need to have FAT32 partition to share files from between ntfs and linux. Thank you, centoser. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Got all the way through the selection of packages. All those time consuming tasks and the install got to formating the drive and crashed on a format error! Since I know exactly how I want to lay out the partitions, is there a way I can boot from CD, and get into Disk Druid to set the partitions and do the formating. Then when I come to the install just select to keep the drive how it is?

Is anyone out there using Druid? After the switchbox announcement today I've been looking into some other gui's and as I'll probably do a trial install this weekend of the free switchvox iso but I thought I'd ask is there any other guis I should be burning trial ISO's of as well? Regards, Dean Collins Cognation Pty Ltd dean at cognation.net <mailto:dean at

Hi, I found 2 identical drives lying around and put them into a system. When booting from a Centos 5.x installer, and when being presented with the formatting option (disk druid), it says I have 1 volume of; mamapper/isw_bdihgcgahe_Volume0p2 I can't seem to get rid of it. I have 2 physical disks but disk druid is seeing 1 volume thats the same size as one of the 2 identical drives.

Hi, It is exactly what I need except one thing. I don''t know exactly if my router is the right place to apply QoS policy. It has two network interfaces and both are 10Mbit/s. The slow part of the network is little bit more far. On their QoS we have 2Mbit and I want all our users to divide this bandwidth equally but also don''t want to unnecessarily restrain their bandwith and to

When doing the 5.2 installation the ONLY drive option provided is mapper/nvidia_cbjcdhfe (250G) My system has 2 SATA - 250G drives and I want to use them in a RAID/LVM configuration. My question: How do I get the installer to let me use DiskDruid to create RAID1 arrays and then use LVM for the mount points? What I've done so far: I've verified that both drives are recognized by

Hello all, I've got CentOS 5.2 installed on an old Pentium III server. The server is used by a club at my school, and they are rapidly running out of room on the internal IDE drives that are configured in software RAID 1. I have a Silicon Image SATA controller in the server, and I was planning on adding two more SATA hard drives to the computer. Is there a GUI like Disk Druid for

Hi all, I've seen the XFS filesystem is not available in Druid partition tool. ?Is there some way to add XFS in normal instalation process? ?How? Thanks in advance. -- Jordi Espasa Clofent PGP id 0xC5ABA76A #http://pgp.mit.edu/ FSF Associate Member id 4281 #http://www.fsf.org/ -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type:

Hi folks, I've been a trixbox user for a few years now but I'm thinking about jumping ship. Trixbox is great, but it's missing two features out of the box which are really important to me: outbound faxing (hylafax) and imap voicemail. I see no indication that they will be included anytime in the near future, so I have a choice to make - I've looked around at Elastix,

hi i want to ask for your opinion what is better for a call center 100 current calls and other 200 current calls make the server step by step or use a auto install cd like asterisk now, druid elastix ....? and why? Thanks David -- (\__/) (='.'=)This is Bunny. Copy and paste bunny into your (")_(")signature to help him gain world domination. -------------- next part

Hi there, I need help in implementing Asterisk with LDAP. I' ve installed Asterik 1.4 with CentOS 5.2 and I would like to use with it an existing zimbra LPAD. thanks, -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081018/5f725eea/attachment.htm

hi i am thinking to use some xorcom hardware i only used digium hard... what do you think? it work ok? what about echo? it is plug and play only reload or i need to restar asterisk ? i understand the drivers are in the trunk of asterisk, is this rigth? have any one a conf file of a xorcom device? any other important comments are welcome. Thanks David -- (\__/) (='.'=)This is

https://bugzilla.mindrot.org/show_bug.cgi?id=1951 Bug #: 1951 Summary: Add home directory facility for chrooted environments Classification: Unclassified Product: Portable OpenSSH Version: -current Platform: All OS/Version: All Status: NEW Severity: enhancement Priority: P2 Component: sshd

---On Sat, 2006-09-02 at 07:42 -0500, Gerald Waugh wrote: We have a problem with upgrade to 4.4 When we run 'yum update' everything appears to be OK But, if we reboot the server with the new kernel, we get "kernel panic" when the new kernel attempts to load. The CentOS splash screen shows briefly, but not long enough to select the old kernel Gerald (let's try it like