similar to: ISDN Cards in the USA

Hello All, Has anyone configured bri to answer for only one msn? In essence, when the primary is busy I want to have channel 2 ring. I am using an eicon diva server bri I know I saw it in the windows interface, but don't see it in the linux setup. Regards, Greg

I'm looking to use Asterisk with Verizon ISDN centex service in the US. I'd be connecting to an NT1 so I'd need an S/T interface. Users would have SIP phones registered with Asterisk and sharing the ISDN lines. The only PCI ISDN card that will support ISDN signalling in the US seems to be the Eicon Diva Server cards. These are hard to find and very expensive ($2500 for the Quad

Hi- Because a majority of my customers are in Europe, I've gotten quite used to working with ISDN (PRI) and BRI on a regular basis. Recently one of my customers asked me if I could terminate a few lines locally here in the USA (California), so I called up SBC to enquire as to how much it would cost to install a BRI here. Although the rates were reasonable (except the installation), I got

Repost, first one never made it to the list... -----Original Message----- From: Gregory Wiktor - ADCom Corp. Sent: Thursday, September 29, 2005 3:20 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: Voice Prompts, what do you think? Good voice. Should we record a new prompt-set? Hello all, I have someone working for me who has a nice phone voice. I looked at

Hi, Anybody have lots of experience with PCI ISDN cards and Asterisk? I'm thinking of getting a BRI in my house to deliver more advanced signaling to my PBX (yes, I'm a geek :-)) but I've never played with isdn4linux. Is there any particular BRI card that works better with Asterisk than any other? Also, can the BRI interface cards participate in conference, etc., since they

> Thank you all for valuable input, > > another question: when do I actually need the echo cancellation > (hardware / on board /on module ) ? > It depends on your environment. If there are still analog devices in addition to VoIP, I'd say always, but Asterisk has a rudimentary echo canceller already on board. The Telcos use echo cancellers themselves, but it cannot hurt to

Hello All, I recently put in a zaptel 1fxo/1fxs card. I am experiencing heavy static. Even with the pots line disconnected, if I do a dial I still get static. This way I know it's not the line, but rather something on the card. I tried alternate pci slots. This card has a power connector, does anyone know what the power requirements are? The unit is in a small case with a 2.4ghz p-4 and

Hi, please whoever has some expertise in choice of BRI ISDN cards, please restore my faith in community support :) (on private email I can probably explain more than fits for a public forum) Most I'd like to ask is about what to choose, out of what is available... My locality is United Kingdom, lines from British Telecom (BT), but any advice / pointers (I googled around already) are

Hello, I'm looking for an ISDN BRI-U interface for use in the US. I'm primarily interested in using the BRI as a trunking interface into the PSTN with Asterisk. Naturally, cheaper is better. I currently use a Nortel Norstar system with BRI-U trunks, and really like the digital PSTN interface. Would really like to replace the whole mess with Asterisk but want to keep the ISDN trunks.

Hi all Hi,I'm facing a strange issue where by SANGOMA not detected by goautodial system , Thats the problem : Configuring ISDN BRI cards [A500/B700] ------------------------------------ No Sangoma ISDN BRI cards detected Press any key to continue: ------------------------------------ Configuring GSM cards [W400] ------------------------------------ No Sangoma GSM cards detected

Hello all, I was wondering if anybody knows where one might obtain a PCI ISDN card supporting a single BRI for use with Asterisk in Australia (and using something like chan_capi). Because of the Isdn4Linux DTMF issue, I don't want one of those cards. I've already spent too much time messing about with my current card. I'm after something like the AVM Fritz! cards. I found one place

Checkout Beronet ISDN cards and Berofix Gateway (appliance or pci card) Personally for my last installation I chose Berofix card which is rock solid and reliable, yet easily configurable. With berofix you don't need telephony drivers on the host system, the isdn card is detected as a NIC and all configuration is done using a web interface. Then you configure FreePBX a new trunk to use the

Hi, I'm after some ISDN card resellers in Australia. I've noticed the AVM cards should work well here, however I've found the reseller here has no website, is listed in Yellow pages as management consultants (??) and when I called quoted almost $400. Does anyone know where I can get the AVMs in Australia a bit cheaper or another card (not the Netjet) that works with Asterisk.

Hello! I have a staff member abroad and need to provide him with the ability to make local calls. The features I need are: * Possibillity to make calls at local (Icelandic) charges from Ireland office. * Possibillity to call the local Icelandic number and reach the Ireland office. I'm also wondering if there is any isdn based solution since there is a possibillity of another staff

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom

Hi All, I currently run asterisk in our office (in Japan) and use a cisco PRI gateway for connection to the PSTN. I would like to setup some more systems for our smaller offices (in Japan) that would use BRI and preferably using a PCI card in the asterisk box and not a seperate Cisco gateway (expensive). HOWEVER, Japan has this INS64 protocol for their BRI lines and im not sure what cards

Hello I want to setup an Asterisk in several offices with 4 BRI ISDN. I am looking for recommendations on hardware. Criteria would be ease of setup, reliability and cost. The Eicon 4 BRI cards seem fairly pricey. Shame Digium don't do a ISDN BRI card. Angus -------------- next part -------------- An HTML attachment was scrubbed... URL:

What types of ISDN BRI cards work well in Europe (Guadeloupe, Martinique and France) ? For example: AVM C2 or AVM C4 or eicon Diva server 4 BRI? Any others? Which driver is appropriate? Ray Burkholder ray@oneunified.net http://www.oneunified.net 704 576 5101 -- Scanned for viruses and dangerous content at http://www.oneunified.net and is believed to be clean. -------------- next part

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Yes, i know that there are many ISDN card on the market. But when i spend money for ISDN card, i prefer to be Digiums, to get all support and help Asterisk :).