similar to: TE110P experiance

Perhaps everything isn't as spiffy as I thought When running zttool the card still reports as internally clocked Zaptel.conf: # Global data span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 loadzone=se defaultzone=se And as pointed out by Peter I do get a lot of D-channel warnings ... Aug 9 16:21:25 NOTICE[1350]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 And

Good Day list, I am having some issues with my card in that it wants to share IRQ's with everything else in my box. I am running WhiteBox Linux 3.0 Is there a way to tell linux to assign a specific IRQ to a card. (unfortunately my MB does not have feature of assigning IRQ to slot) Further, I know this is silly to even ask but I

Hi All, I have a TE110P in E1 mode, in a dell poweredge 250. The 30 channel E1 supplied is from a telco in Australia, with the following in my zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 (yes the provider has NOcrc4 for some reason) After installing the latest cvs libpri and zaptel, I successfully loaded the kernel modules. The card is verified as not sharing an

Same problem here: if call come over ISDN PRI and it is for a SIP phone that equals to strong echo situation, at the SIP end. Interestingly this doesn't happen on all calls but it does on 95% of them. Asterisk load at that moment is insignificant - 1 to 2 calls. I have tried with all possible echo cancellers in zconfig.h, with and without MMX, and with and without CFLAGS+=-march=i686 in

Hello All, I have got my TE110P working at the hardware level, turned out to be a dodgy cable causing the Yellow errors in zttool. However, now I am getting yellow errors in asterisk, but zttool shows nothing out of the ordinary. here is my current config, and some asterisk console errors, any suggestions most welcome. zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31

Has anyone had any compatibility issues with a TE110P card installed on a Dell Poweredge 1950? I noted the following error on the LCD display of the Dell Poweredge 1950: E1711 PCI PErr Slot 1 E171F PCIE Fatal Error B0 D4 F0. The Dell hardware owners manual states that it means the system BIOS has reported a PCI parity error on a component that resides in PCI configuration space at bus 0,

I think you can use normal network cable, I'm from Italy and it's work perfectly Good luck -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Milo? Kocbek Inviato: mercoled? 27 luglio 2005 10.04 A: Asterisk Users Mailing List - Non-Commercial Discussion Oggetto: Re: [Asterisk-Users] TE110P Cable Pin Out

Hi everyone I have a Digium card TE110P and after plug it, turn on the computer and configure, the LEDs don't light up in spite of what Digium FAQ says about the LEDs: When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP? ... The TE110P LED's will light up RED when the span is configured and kernel module is loaded. If configured correctly and a circuit or channel bank is

Folks, I installed a te110p to connect to an E-1. Ensured the jumper is on for E-1, installed the card, and got the following from the phone company: hdb3 encoding (verbally confirmed ccs) euroisdn switchtype pri signalling So I set up zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15 unused=17-31 dchan=16 loadzone=us defaultzone=us Card tries to come up but goes into RED alarm. Occasionally cycles

I'm getting unstable behavior with my newly installed TE110P T1 card. It hangs up any incoming call anywhere from 20 seconds to 6 minutes. Frequently, when you call back on our incoming T1 there'll be an automated announcement (maybe from the telco?) stating "we are unable to complete your call at this time". I simultaeously get a yellow alarm on the system and shortly

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Guys. I have an issue with a te110p card and also some tdm04b cards on the same system: Zttest returns this for the tdm04b cards: [root@mollendo ~]# /usr/src/zaptel-1.2.4/zttest 38 -v Opened pseudo zap interface, measuring accuracy... 8192 samples in 8191 sample intervals 99.987793% 8192 samples in 8192 sample intervals 100.000000% 8192 samples in 8192 sample intervals 100.000000% 8192 samples

I have an Asterisk server that was running fine until Sunday. Monday there was a power outage and the server was off most of the day. This server has a TE110P, two TDM04B and an Astribank 32. Today I noticed that the TE110P started having IRQ missess. Before today it only had about two or three per month. Today, this is the miss count after ten minutes on: IRQ Misses: 1443

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Helo, I have problem with Digium TE110P connected to CISCO 3640 (port on NM-HDV-2E1-60) wth PRI E1 link. I use CISCO now for testing but when I tried with real PBX problem was exactly same. I have this messages in Asterisk conole and log sometimes: NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Usually 2-5 such messages in series, can be repeated after 10

i get this message with a red signal on TE110P card: ***************** TE110P: span configured for... Calling startuo (flug is 4099) wcte1xxp: Setting yellow alarm ***************** what does mean ? thank you :)

Hello all, Has anyone use the Supermicro PDSME+ in combination with the TE110P successfully? My experience so far is not very good. I am running trixbox 2.0 but: 1) with zttool I am getting IRQ Misses. Don't seem to have IRQ conflict, but I am now running my SATA HD in DMA. And I am not able to set it in DMA(HIO... operation not permitted) 2) With zttool the Alarm is RED 3) When I do the

Hi!, this issue makes me crazy. I read a lot of docs, also * mailling list and I try a lot of things without success. Any help will be appreciated. Here is the info: Hardware: -------------------------------------------- Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050 Digium TE110P Software --------------------------------------------- Asterisk version 1.2.12.1

Hello Approximately every 15 minutes I'm getting the following error (on all channels): [Apr 7 01:34:27] WARNING[6530]: chan_zap.c:6628 handle_init_event: Detected alarm on channel 31: Yellow Alarm [Apr 7 01:34:27] WARNING[6529]: chan_zap.c:2388 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! [Apr 7 01:34:27] == Primary D-Channel on span 1 up