similar to: Polycom Soundpoint 500/600 MiniBrowser

Has anyone been able to get the minibrowser on the Polycom SoundPoint IP 500/600 phones working? If so could you share the relevant sections of your config with me?

Has anyone got this to work? Under Idle Display Animation, the administrators guide says "For example, a company logo could be displayed".. In the ipmid.cfg file, I enabled 'ind.idleDisplay.enabled' (ie changed it to 1), and under the IP 500 section, I added an entry for the bitmap that I want to display: bitmap.IP_500.66.name ="arf" but from there I'm not sure

I found this solution from the web and figured I'd share it because it affects all phones getting input from IIS. Map .gif, .jpg, .css etc (in my case I used .xhtml for the Polycom 601) in IIS under your sites: Properties -> Virtual directory tab-> Configuration -> Application configuration -> Mappings tab. Make ASP DLL [..\inetsrv\asp.dll] to handle these files. This

Hi all, I have a Polycom Soundpoint IP 600 that looks like it is fried. It either has a bad or corrupt bootrom (I'm guessing). It never gets to the prompt that asks if I want to enter the setup configuration or continue booting. When plugged into power, it turns on, shows the Polycom logo for 3 seconds and then pretty much goes dead with two red lights on. The one in the top right corner

I'm attempting to set up my SoundPoint 501 with my Asterisk server. I've configured DHCP and TFTP and successfully updated both the BootRom and SIP application. I've also created a custom cfg file for this phone's MAC address and the settings seem to be taking just fine. I can see that the phone registers with my Asterisk server but 'sip show peers' reports that the phone

List, I am having trouble with one of our IP600. Every five days or so, the phone locks up. This is the third 600 I have put in place. I am running asterisk 1.0.9. Has anyone had this problem with the IP600? This electronic message transmission, including attachments, is for the exclusive use of the individuals to which this e-mail is addressed and is to be reviewed and used exclusively

I got em. You want em? Anyone know how I can get these to the site listed on the Wiki? Thanks, Wiley -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050512/dfee13b3/attachment.htm

I can't figure out how one upgrades the boot ROMs for the Polycoms. I've read the wiki, I've checked the docs, I've looked here, there, everywhere; I hoped it might be through the web interface, through DHCP... but I can't see how to do it. Suggestions? Thanks! -Ken

Hi Folks, I have posted a couple of message to the list and do see them, even after waitin for long time (2 days). Can someone please point me to the rules for posting to this list? I think it had to do with the subject that I was looking for. I was looking for IAX terminiation service that can handle high volumes. Thanks John. --------------------------------- Yahoo!

Hello all, I need the bootrom.ld file to set up some Polycoms I have Platform: Model=SoundPoint IP 330, Assembly=2345-12200-001 Rev=A I've publiched on my FTP files downloaded from http://support.polycom.com/PolycomService/support/us/support/voice/soundpoint_ip/soundpoint_ip330_320.html (3.2.3 combined and split zips) but my phones are still showing the message: "error, application is

I am getting to my wits end with these phones (and so is my boss). I am getting an random echo on these phones and I have an issue opened with Polycom and its been in their research and development department for almost a month with no results. I have noticed that I get a message "RFC3389 support incomplete. Turn off on client if possible" in asterisk. I have researched this and made

now that I have finally figured out what I was doing wrong with my polycom phone and got it to read the configuration file Im changing some gains. I successfully changed the gain for the ringer... It was too low for me. Does anyone know which gain would be for the call waiting and which tone would be for the "hands free" mode? Thanks

I've been trying to get the polycom 550 phones to show a idle display bitmap but have not been successful. Anybody have any experience with this? The manual gives instructions (http://www.polycom.com/common/documents/support/setup_maintenance/products/voice/soundpoint_ip_soundstation_ip_administrators_guide_v2_2.pdf) but they do not seam to work. So far i've done the following in my

I have just spent the morning playing around with a Polycom IP600's microbrowser. Everything is working pretty well. In answer to the question of what type of XML it runs, it appears to be more or less XHTML-compliant. I have created a basic set of web pages allowing users to clock in and out against our MySQL timeclock system, running a PHP back-end. It's running like a champ.

I have the following situation: Asterisk 1.2.1 25+ Polycom 501 telephones. Bootrom 2.6.2.0032 Application 1.6.2.0041 Some 501's local to my network, some across the great INTERNET divide. PRI connected to Sangoma card. Issue: horrible echo (and squeals, and "underwater-like" sound) on speaker phone when calling from extension to extension. echo not present when calling outbound

(new asterisk user - currently setting up Polycom IP600 phones) Does anyone know if it's possible to make a sip phone instantly pick up on speakerphone when a particular call comes in? Eg so that you can quickly bother someone across the office without making them reach for their phone?

Could not find your post for 4 months ago. -------------- Original message -------------- From: "Anton Krall" <akrall-lists@intruder.com.mx> > Yes, check a post that I made about 4 months ago, I posted the cofig for > setting the speaker, handset and ring volumes .. > > |-----Original Message----- > |From: asterisk-users-bounces@lists.digium.com >

Hi, I have been trying a (really simple) push application for the Polycom microbrowser, using a Polycom 650 with 3.2 firmware. I can't do anything, I always get "Push message cannot be displayed" back from the Polycom phone, and all I am sending is the Polycom example : <PolycomIPPhone> <Data priority=?critical?> <h1> Fire Drill at 2pm </h1>

What headsets have people found work well with the Polycom Soundpoint 500 & 600? If any of the headsets that work with the Polycom's also work the Cisco, that would be an added bonus, but is by no means a requirement. I am not looking for a headset that requires an external amplifier, but rather a headset that can make use of the headset jack on the phone itself.

Oooo I think I am gonna poo my pants. Using the microbrowser on a Polycom 601, I was able to get it to execute a cgi script upon selection of an item. The cgi script used Net::Telnet connect to the manager interface on another Asterisk system, call the user back at their phone and then bridge the call to the number associated with the microbrowser menu option. That's pretty schweet. :)