similar to: Suse 9.2 + CAPI Driver

Hello, I have problem with capi, I can't install it. I have putted all info what I did and what I get :). I think you can suggest me how to solve this problem.and thanking you in anticipation. I have ISDN Frtiz!Card PCI v2.1and I want to install it to my ubuntu box (kernel: 2.6.17-10-server). Using command "lspci -vv" , I can see that kernel finds this card: *02:0d.0 Network

Hello all, I'm trying to setup a AVM C2 card. I have read the kernel requirements for this card. <M> CAPI2.0 support [*] Verbose reason code reporting (Kernel size +=7K) [*] CAPI2.0 Middleware support (EXPERIMENTAL) <M> CAPI2.0 /dev/capi support [*] CAPI2.0 filesystem support <M> CAPI2.0 capidrv interface support My problem is when I make a "make

All, I have been trying to get CAPI4Linux working on my machine and being frank am failing miserably! I am looking for any help available, I am real newbie (so please be gentle) and choose to run Mandrake 9.2 as it appears quite friendly (or so I thought!). I have been following the guidance found at http://www.voip-info.org/wiki-Asterisk+How+to+connect+with+CAPI for the AVM card (actually I

Hi, I added a Fritz!PCI card to my asterisk system which is running on fc2 !. I installed the avm modules (fcpci) and when i try an capiinit and a capiinfo then everything seems to be OK (you can see capiinfo and lsmod at the end of the text) !. I installed the asterisk chan_capi module and when i start asterisk and enter the command capi info on the command line i get back: *CLI> capi info

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hi, i will use an AVM C2 controller with asterisk. How can i use both card ports ?? On the voip-info.org Wiki is only notice to: You will need a section for each controller in /etc/asterisk/capi.conf so the C2 will have 2 sections. But how is look like this ? Only on the first port is asterisk assume connections, but nothing on the second card port. In the dmesg is only the capidrv-1 shown,

Hi Armin! I have problems on debian sarge with standard 2.6.8-2-386 kernel. I've installed the packages: kernel-headers-2.6.8-2 kernel-headers-2.6.8-2-386 kernel-image-2.6.8-2-386 kernel-kbuild-2.6-3 kernel-source-2.6.8 Then I unpacked the kernel sources into /usr/src/kernel-source-2.6.8 and made a symlink from /usr/src/linux --> kernel-source-2.6.8 Then I entered

I'm trying to compile chan_capi-0.5.4 on Slackware 10, but I have bunch of errors. (By the way, can I use chan_capi for ISDN card with winbond w6692cf chipset?) I'm not a linux expert, still :-) Before compiling, when I type "modprobe capi" to load capi module, and then "lsmod", i get list of modules: capi 6208 0 kernelcapi 30496 1

Hello List! I have this "simple" problem: fileserver:/usr/src# capiinit start modprobe: Can't locate module kernelcapi ERROR: cannot load module kernelcapi Although, i think i hav everything build in, and loaded: ~# grep -i capi linux-2.4.27/.config CONFIG_ISDN_CAPI=y CONFIG_ISDN_CAPI_MIDDLEWARE=y CONFIG_ISDN_CAPI_CAPI20=y CONFIG_ISDN_CAPI_CAPIFS_BOOL=y

Hi, I recently subscribed to xen-users asking about a powernow-k8 problem, but in the meantime I am not sure if the users-list was the right place for it. So I decided to repeat my question here ;-) My current config is attached. --- snip --- Hi, I recently installed Xen on my AMD64 for my first time and so far, everything seems to work pretty fine. :-) I tried to enable cpu frequency

Good day, *newbie alert* I try to run * with capi_chan (and later on SIP). System: Debian 3.0 / apt-getted most stuff except chan_capi and b1.t4 HW: AVM B1 ISA / Celeron 400 / 128MB RAM Starting * the following ends up in the messages Jul 22 19:47:03 WARNING[16384]: File chan_mgcp.c, Line 2925 (load_module): Unable to get our IP address, MGCP disabled Jul 22 19:47:03 WARNING[16384]: File

I tried that but it still doesn't work... I think I don't have the correct approach. Have I to install any ISDN drivers (=modules ?) BEFORE dealing with CAPI ? If yes, why shouldn't I use the hisax drivers (which are kernel ones) instead of fcpci drivers (which doesn't seems to work, by the way...) And finally, how is it possible to link the two modules together? As you can see,

Hello, list a have a problem i can start asterisk, i get the fowlling error: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Feb 11 13:50:36 NOTICE[2535]: chan_capi.c:2636 load_module: CAPI not installed! Feb 11 13:50:36 WARNING[2535]: loader.c:345 ast_load_resource: chan_capi.so: load_module failed, returning -1 Feb 11 13:50:36

Hi, I am trying to configure a Diva Server 4BRI to work with chan_capi. Here are the steps that I took: - compiled fresh kernel with new-style CAPI support: i4l_divas_1.2 - got the divactrl_1.2 utilities, configured the card startup scripts, - rebooted, card firmware loaded properly, "capiinfo" displays detailed info on 4 controllers, however there is an error message: FAC REQ -

hi list. after my unsuccessfull experiences with mISDN i tried again to implement a zaphfc based solution. problem is: sound on calls via capi is stuttering/broken and therefore unuseable. my conf: - cel 1300, 256mb ram - avm b1 via capi connected to my outgoing ISDN - acer surf pci via zaphafc and crosslink cable with termination as internal bus - siemens gigaset 3035 as internal phone -

Hi, I have a problem for install chan_capi My pc: Suse 9.1, with asterisk current stable en cvs I have download http://www.junghanns.net/asterisk/downloads/chan_capi.0.3.5.tar.gz And the path from http://www.levigo.de/VoIP/chan_capi-0.3.5-cvs-HEAD-patch.tar.bz2 And patch the chan_capi # cd chan_capi-0.3.5 # patch -p1 < chan_capi-0.3.5-patch.diff # make /for install My error

Hi ! I've fetched a spare AVM B1 card from the cellar, and installed it. After "modprobe b1pci" I did "capiinit" and capiinit moaned about a missing t1.b4. So I search the web and found one at http://www.avm.de/ftp/cardware/b1/x_misc/ddi/. When I now look at the controller, I finally see p2p-mode: # cat /proc/capi/controllers/1 name b1pciv4-a400 io

I have an asterisk installation connected to 2 isdn lines via an AVM C2 card. modules seems to load well, lsmod gives : c4 19588 4 b1 24192 1 c4 capidrv 28468 2 isdn 134604 9 capidrv slhc 7552 1 isdn capi 18112 4 capifs 6024 2 capi kernelcapi 46112 4

Hi *, This is my first message to this list, so I hope I am not breaking any rule with my post. My question is the following: can I establish a voice connection over an ISDN interface by using a bluetooth dongle to connect to the ISDN access point? Here follow the details: I have compiled and configured asterisk. Everything seems fine except that when I configure asterisk to use the ISDN