similar to: SV: QSIG, Asterisk and Eicon DIVA

I have read most of Eicons information on Q.SIG, and I am able to load the Q.SIG protocol (instead of ETSI for example). No strange logging in divacrtl mlog. But how do I tell Asterisk to understand Q.SIG? My PBX is configured for QSIG, but I cannot see anything on my trace when trying to make a call via the S0(Q.SIG) Janne > -----Ursprungligt meddelande----- > Fr?n:

I am using Trixbox 1.0(Asterisk 1.2.7.1)at a customer site. They whishes to change the default Voicemail behavior. Standard behavior No answer/Busy -> send to Voicemail Requested behavior No answer/Busy -> message that if you press 9 you will instead be cent to reception -> send to Voicemail or Reception if 9 pressed. I want this to always happen when Voicemail is invoked. How

Hello all, I am trying to set up asterisk and hylafax to send and receibe fax. The machine is connected to the PSTN is an Eicon Diva BRI (1 BRI port). My problem is that , when I send a Fax from the PSTN to this machine, the asterisk or diva or hylafax, does not detect this call as a fax and asterisk answer that call like a voice call. How sould I configure the software modem (iaxmodem) to use

Hi, I would like to set up a high density FAX/PBX server, am looking at using Eicon Diva E1 card with Asterisk and Hylafax sharing channels, is this possible. I know Extensions can be reserved for voice OR fax with the combination of chan_capi used for * voice, capi4hylafax on fax but then channels must be dedicated rather than shared ie. would like to be able to answer voice/fax on same DID.

Hey guys This is probably for Armin, but I thought maybe someone else might have something I could try. I'm having a problem with one of my Eicon Diva V-4BRI cards and I'm trying to work out if its a driver configuration error, card failure or telco problem: I have an Asterisk box running -- the Eicon drivers see all four ports on my card, capi.conf is configured with all four ports

Hello everyone, I'm having some errors while compiling the source code for an Eicon Diva BRI card. I am using Fedora Core 6 with a compiled from source Linux kernel 2.6.19. I have downloaded the Eicon Diva source RPM (divas4linux_EICON-106.12-1.i386.rpm) and installed it already. When I go to /usr/lib/eicon/divas/src/ and run ./Build, everything starts correctly until that part where it has

Hi! I've bought the EICON DIVA V-2BRI card an begin installation soon. Are there any issues with certain kernels? E.g. the standard debian kernel 2.4.27-2-386 and kernel-image-2.6.8-3-686. Further current kernel 2.6.16.14 would be an option. Thanks Klaus

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

Hi, I'm trying to get an Eicon Diva Server4BRI card running under Ubuntu 6.06 - by downloading the v3 driver package from Melware and compiling everything. Yet, after activating the necessary modules (divas and divadidd) and interactively configuring the card (/usr/lib/divas/Config), starting up the adapter fails! The error "/usr/lib/divas/divactrl load -c 1 -Debug" produces

Dear all, I'm planning to buying Eicon Diva Server V-BRI for my asterisk server and run with chan_capi. Is anybody using that card ? Would appreciate any feedback. Bartosz

I am trying to use chan_capi with an Eicon Diva Server BRI. I installed the Eicon drivers from source including CAPU and I can use the board correcly using tty_test and minicom over /dev/ttyds01 or /dev/ttyds01. I need to insmod capi ( why? it is not written anywhere) and then capiinfo shows me all board parameters, but I have to break it otherwise capiinfo doesn't exit at all, but I don't

Hi! I'm trying to enable echo cancelation with my Eicon Diva Server 4 Bri card. I've enabled it from zapata.conf, (as I read from www.voip-info.org) ------------------------------- ; Enable echo cancellation echocancel=64 echocancelwhenbridged=yes echotraining=2000 ---------------------------- but nothing seems to change, echo is still present. Any idea? Should I enable/change something

Hello, I'm thinking of deploying Asterisk. I already have a handful of EICON Diva 2.01 PCI ISDN cards. I was thinking if it's possible to insert 4 such cards to my PC-Asterisk server (which I yet have to install) and use them as 4 lines in case anyone has to call me in / I have to call out using ISDN line(s)? Any reply appreciated. Tomek

Would any one advice how implement Diva Server BRI or PRI card to support fax and data modem? In Eicon's website, it says that they support these. But there is no FXS port on the card, how it can be connected to Fax machine or data Modem? Thanks in advance. Isaac Xiao -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi (Armin?) ! Today I had a problem with Diva Server 4BRI-8M 2.0. Asterisk 1.2.12.1 chan_capi-cm-0.6.5 divas4linux-melware-3.0.f-106.622-1 Asterisk could not receive and make calls on the BRI ports, although the ports looked fine within Asterisk. I usually use "/usr/lib/divas/divactrl dchannel -c 1" to test line activity. This time there was no activity (cryptic log

I just wanted to let you know that it's possible to use Eicon DIVA PCI 2.01 ISDN cards (not "server" divas) with asterisk. First thing to do is to load the module. If you have two of these cards, you should do it like that: modprobe -v hisax protocol=2,2 type=11,11 And now you can have up to 4 incoming calls with two cards (try calling yourself and see if anything gets into

Hi Armin! I want to backup my Eicon Diva configuration (I'm using melware v3 drivers), but I could not find them. Where does Config Wizard stores the configuration? thanks klaus

I have just acquired an eicon diva server BRI-2M card for using with asterisk and hylafax. Of course i installed it in a new server with Debian Lenny wich has a kernel 2.6.26+ I have downloaded the latest drivers (9.0) from the Eicon web site and i'm having trouble compiling them, specifically the divaTTY driver i need to use with hylafax in the same server. On the icon web site there is a

Hi list, Does chan_capi work with kernel 2.6? The Eicon Diva server card loads fine judging from /var/log/messages but Asterisk gives an error when trying to load the chan_capi module. I'm using chan_capi-0.3.5, zaptel-1.0.0, libpri-1.0.0 and asterisk-1.0.0 on a Fedora box with kernel 2.6.8-1.584. Zaptel and ilbpri work fine as does *. I have seen a msg that may be related and don't know

Hello, is it possible to use a eicon diva server 2M as FXO ? Regards Andreas Moroder