similar to: Sparc hardware, Linux and X100P REVISITED

It seems the information out there on this topic was confusing enough to cause me to waste a lot of time, and that this topic is rehashed periodically. So now it's my turn.... I had a modem with an Intel 537EP chip on it and thought it might work with the zaptel drivers. Initially, it seemed the only issue would be the PCI device & vendor codes. Then, I ran into the problem that

So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel 2.6.16.16. Everything has been fine up until now. I compile the 1.2.5 Zaptel drivers without a problem, get the udev configuration in, modprobe zaptel, and finally modprobe wcfxo. At this point, I get the message: ZT_CHANCONFIG failed on channel

Hello everyone. I hope that this isn't a sore topic, but I've spent a week now reading through everything I could dig up from the archives on this topic, and I'm not yet satisfied with any conclusions presented there. I've also spent a few days hacking on the Asterisk code, trying to understand how things work better, and I'm still not ready to give up. I well-realize

Asterisk doesnt answer the ringing phone, so according to some doc that I read I should try and see if I get I/O on /dev/zap/1. I dont see any from cat /dev/zap/1 while it is ringing or otherwise. Dmesg seems to have a few odd things (out of space), not sure how relevant. Does anyone have any ideas? Here is my info: <built zaptel / asterisk CVS from 2 days ago> [root@homestar etc]#

I have just got my X100p card and am trying to install it. I have built and installed the zaptel drivers without any apparent errors and I am now trying to get them working. I have the following in config files In /etc/zaptel.conf fxsks=1 In /etc/asterisk/zapata.conf signalling=fxs_ks context=default channel => 1 Now when I try ti modprobe the drivers this is what happens: Command:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm experiencing frequent kernel panics when using the X100P card under the 2.6.6 Fedora kernel. I've attached the kernel output to this message - - it looks like the IRQ stack is overflowing and trashing some memory, causing a series of oopses followed by a complete crash. I have just hacked the kernel to reenable 8k stacks and will see

I still have echo during the first 15 seconds (or so) of each call, and the exact same thing is happening with either of two X100P in the same 2.2ghz system. asterisk# cat /proc/interrupts CPU0 0: 198457690 XT-PIC timer 1: 60 XT-PIC keyboard 2: 0 XT-PIC cascade 3: 0 XT-PIC usb-uhci 8: 1

I have two X100P cards that were working just fine for months. When I run modprobe wcfxo today I got the following error: ZT_CHANCONFIG failed on channel 2: No such device or address (6) /lib/modules/2.4.19/misc/wcfxo.o: post-install wcfxo failed /lib/modules/2.4.19/misc/wcfxo.o: insmod wcfxo failed The output of dmesg said that wcfxo:Out of space to write register 06 with e0. What?s

Hi, I'm trying to figure out why my Sweex CA000022 is not detected by wcfxo on my SuSE Pro 9.3 running on a VIA EPIA SP motherboard. The card should work as its an Intel 82537EP based card. When Booting the IRQ assignments for the board indicate: Bus Dev Func Vendor Dev Class 0 20 0 8086 1080 0703 lspci shows: 0000:00:14.0 Modem: Intel Corporation: Unknown device 1080

Ok, I have 2 PC's that are identical. I loaded Redhat9 on the first and Asterisk and installed a x100p card and it works fine. I ghost the first PC and install the ghost on the second PC. Everything comes up on the 2nd PC but I can't get it's x100p card to load. The systems sees the card, it's on interrupt 11. It shows up in /proc/pci and /etc/sysconfig/hwconf and lspci shows it

Hi. I have a x100p card installed on my asterisk box... my zapata.conf file includes the following lines: [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 echocancel=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 Basically, the zapata.conf file generated by make samples. Then in my extensions.conf I have this: [default] include => demo And demo is

Hmm, I don't have /etc/modprobe.conf, and wctdm is giving me problems. Which device is it talking about? [root@asterix /]# modprobe wctdm /lib/modules/2.4.20-8/misc/wctdm.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Hi All, Googling X100P Clone I found several information about these cards and seems that some winmodem has the same chip used from the original X100P. Here below a list winmodem which should work as X100P clone: 1057 Motorola 5608 SM56 PCI Fax Voice Modem E159 Tiger Jet Network Inc 0001 Tiger 300/320 PCI interface I bought one "Trust 56k V92 PCI Internal Modem MD-1100" which has the

Hi, I have problem with X100P clone card.I can not force it to work under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2. I looked over and over on configuration and could not see any mistakes. Here are relevant configuration files. /etc/dahdi/system.conf > fxsks=1 > echocanceller=mg2,1 > loadzone = hu > defaultzone = hu > dahdi_tool > OK Wildcard X100P

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <meta content="text/html;charset=ISO-8859-15" http-equiv="Content-Type"> <title></title> </head> <body bgcolor="#ffffff" text="#000000"> <span class="postbody">Hello! <br> <br> I have a

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo

I am starting to dip my toes into the asterisk world, and to that end I've scavenged an old PC (this is a home project, and I have basically $0 to spend on it), and installed FC1. I've purchased a clone X100P (or at least I was told it was), and I am trying to get it to work. However, when I try and load the wcfxo module, I get the following errors... [root@loudhoward root]# insmod

I have * working on my Sony Vaio PCG-FX120 laptop. I am trying to get * to recognize my internal PCI Intel modem as an FXO port. I have modified wcfxo.c in order to identify the PCI modem properly. Based on output from dmesg, wcfxo didn't recognize the modem until I inserted the proper vendor and device IDs into wcfxo.c and re-compiled. Note that the error message from "modprobe

[root@server ~]# modprobe zaptel [root@server ~]# modprobe wcfxo ZT_CHANCONFIG failed on channel 1: No such device or address (6) FATAL: Error running install command for wcfxo [root@server ~]# ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address