Displaying 20 results from an estimated 10000 matches similar to: "RE: Asterisk-Users Digest, Vol 7, Issue 239"
2006 May 27
3
TDM
The TDM01B is 4 port capable but has only 1 FXO module. I'm running asterisk
1.2.7 and zaptel 1.2.5. I cannot seem to get the TDM01B working. When I do
the zttool it shows 4/1/0. I can dial out from a POTS phone up to the point
that the cable plugs into the card.
Here is my /etc/zaptel.conf
loadzone=us
fxsks=1
and here is my /etc/Zapata.conf
[channels]
language=en
#include
2005 Feb 17
8
Trying to install X100P
I have just got my X100p card and am trying to install it.
I have built and installed the zaptel drivers without any apparent errors
and I am now trying to get them working. I have the following in config
files
In /etc/zaptel.conf
fxsks=1
In /etc/asterisk/zapata.conf
signalling=fxs_ks
context=default
channel => 1
Now when I try ti modprobe the drivers this is what happens:
Command:
2005 Aug 12
2
Possibly bad FXS module in TDM400P?
I've got the latest zaptel and cvs asterisk software loaded on my phone
server running FC3. And yes, It's fully updated and udev is setup
correctly. I've got a TDM400P with one FXS and one FXO module
installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this:
[root@asterisk ~]# ztcfg -vvv
ZT_CHANCONFIG failed on channel 1: No such device or address (6)
Zaptel
2006 Feb 19
3
Asterisk start errors with TDM2413E
I get the following errors when starting Asterisk.
== Parsing '/etc/asterisk/zapata.conf': Found
Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to
specify channel 1: No such device
Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open
channel 1: No such device
here = 0, tmp->channel = 1, channel = 1
Feb 19 21:14:35
2008 Mar 27
3
problem about voice when using TDM2400p with VPMADT032 echo canceller module
hi you,
I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk.
anyone have the same problem? pls help me. thanks a lot.
my trixbox and config
2003 Nov 19
1
FXO card still won't pick up...
I recently updated (fresh checkout) to the newest zaptel and Asterisk.
The one I was using before was a couple of months old.
After updating, my zap channels don't work. They won't pick up incoming
calls or dial out. When I try to dial out I get:
-- Executing Dial("SIP/3064-564c", "Zap/g1/ww954.......") in new stack
NOTICE[245776]: File app_dial.c, Line 698
2007 Feb 11
2
TDM02B not working
I am trying to reconfigure an asterisk box that was using an HFC-S card
with bristuff but is now using 2 analog lines therefore I want to use the
TDM02B to connect to two POTS lines. The TDM02B has 2 red modules.
I have this in /etc/zaptel.conf
loadzone=nl
defaultzone=nl
fxsks=1-2
I have /etc/asterisk/zapata.conf
signalling=fxs_ks
echocancel=yes
echocancelwhenbridged=yes
echotraining=400
2004 Dec 10
2
Asterisk 1.0.3 - Signaling on E100P.
Hello list ,
I?m putting to work a new asterisk box.
I?m running * 1.0.3 with (one )
Wildcard TDM ( 2FXS* 2FXO) and
(one) E-100P.
Both boards are working well. ztcfg
don?t show me any error.
zttool list both cards as "OK"
But when i run asterisk on verbose mode
i get those errors :
[chan_zap.so] => (Zapata Telephony)
== Parsing '/etc/asterisk/zapata.conf': Found
--
2009 Sep 27
3
Problems with Digium TDM400 card
I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed.
But still problems:
Here is my ztcfg output:
asterisk:/etc/asterisk # ztcfg -vvvvv
Notice: Configuration file is /etc/zaptel.conf
line 4: Unable to read Zaptel version information.
Zaptel
2003 Nov 05
1
Beginners help
Hi,
I recently purchased two X100Ps and a TMD40B. I have set everything up
according to the instructions however I can't get asterisk to pick up an
incoming call (It just keeps ringing). Also, when I pick up an internal
extension I get dead air. I searched the mailing list for 3+ hours -- What
am I missing?
Thanks in advance for your help.
Here are the installion steps that I used:
2009 Jun 14
2
FXS - TDM400 - No dial tone
I have a TMD400 card installed in a PC with one fxs (installed in slot
2) and two fxos (installed in slots 3 & 4).? fxos work fine but I am
unable to get a dial tone for any devices connected to the fxs.? I
have correctly connected the power supply to the card and I have even
tried moving the card from slot 1 to 2 on the board.
Below is from the console when I try to route a call from FXO on
2004 May 19
4
TDM400P problems with 1 FXS, 1 FXO
Hi-
I'm totally stumped configuring my TDM400P with one FXS and one FXO
module. Before I got the FXO module, I used to have an X101P, and
everything was working very well. Now * doesn't seem to recognize the
FXO channel. I've searched the wiki and the list archives. Stock Debian
3.0 stable installation. Any advice? Thanks.
-- David
Here's my configuration:
modprobe zaptel
2004 Jun 18
5
Problems with X100P
All,
I'm having trouble getting the X100P working.
Lsmod shows :
zaptel 179808 0
I did a .
# modprobe zaptel
and here is my zaptel.conf (comments omitted)
__SNIP__
fxsks=1
loadzone = us
defaultzone=us
__SNIP__
Here is zapata.conf
__SNIP__
[trunkgroups]
[channels]
context=default
switchtype=national
signalling=fxo_ls
rxwink=300
usecallerid=yes
hidecallerid=no
2005 Jul 22
1
Problem with Zaptel FXO..
Hi all, i've installed AMP and Asterisk following the INSTALL file and i have
a problem with the TDM04B with 4 FXO:
[root@srvoip ~]# ztcfg -vv
Zaptel Configuration
======================
Channel map:
Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 02: FXO Kewlstart (Default) (Slaves: 02)
Channel 03: FXO Kewlstart (Default) (Slaves: 03)
Channel 04: FXO Kewlstart (Default)
2008 Mar 18
1
Sangoma FXO/FXS config
Hi all,
I bought a Sangoma A200 card from an online supplier and explained
exactly what I wanted,
3 incoming phone lines to PBX and a life line (some where to connect a
standard BT phone to the PBX incase the power goes, making the BT
phone ring).
I was told to order
1 x FXS module (2 FXS ports)
2 x FXO modules (4 FXO ports)
However being a complete noob, I have connected the 3 lines to the
2007 Apr 19
6
ZT_CHANCONFIG failed on channel 1: No such device or address
I have had a TDM400 with 2 FXO and 2 FXS working for ages (>12 months). It has stopped working. All four green lights are still lit. I have rebuilt zaptel and asterisk and restarted but the problem persists.
/sbin/ztcfg -vvvv
Zaptel Configuration
======================
Channel map:
Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 02: FXO Kewlstart (Default) (Slaves: 02)
Channel 03:
2007 Oct 21
3
WARNING: chan_zap.c process_zap: Ignoring signalling
Hello
I've been googling for this message, but can't find why
Asterisk sends a warning. The configuration files look similar to
http://www.voip-info.org/wiki/index.php?page=Asterisk+config+zapata.conf.sample
It's a TDM card with just one FXO module on it, and I connected an
RJ11 cable to it from the wall plug:
# cat /etc/zaptel.conf
fxsks=1
loadzone=fr
defaultzone=fr
# ztcfg -vv
2004 Oct 06
3
Re 2 x100p cards H E L P (I have no hair left)
Hi
Has anyone had any luck in putting two of these im a box?
May I ask how.... I am starting to go bald....
I do have a suggestion is make another box and link them with iax2
Thanks
Samantha
r2d2:/home/s/samantha# ztcfg -vv
Zaptel Configuration
======================
Channel map:
Channel 01: FXS Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
2
2003 Sep 13
1
ZT_CHANCONFIG failed on channel 1: Invalid argument (22)
no matter which way I have my /etc/zaptel.cfg
this only started happening after a yesterdays CVS update
to my zaptel source...
Line 1: fxoks=1
Line 2: fxsks=2
Line 23: loadzone=us
Line 28: defaultzone=us
<End of File>
Zaptel Configuration
======================
Channel map:
Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
2 channels
2007 Dec 11
4
X100P Fxo card headaches
Hello List,
Im just dipping my feet into the asterisk world, and im having major
fxo problems
Im running Asterisk (from svn) + libpri (from svn) + asterisk-addons
(from svn) + asterisk gui (svn 1.4 branch) + zaptel (svn 1.4) on a
Debian Etch box, with 1gb ram, running all of the services for my home
server (web / db / music server etc), and i would like to run my PSTN
line from Kingston Comms,