similar to: E1 and/or Euro-ISDN specifications?

What server hardware would you recommend for an Asterisk system which are really critical? The additional hardware will probably be two digium TE110P cards, and an Adit 600 platform. If it's possible to run on -48VDC, It would be great! Are there any experiences with any HP or FujitsuSiemens systems? Or other "complete server" systems? Thanks! BR Daniel Nystr?m

hi, i have the problem that i'm not able to set and receive the Service Indication (SIN) from our E1-PRI and from our ericsson BP250. The problem is, that the Bearer Capability (BC) together with the High Level Compatibility (HLC) and Low Level Compatibility (LLC) forms the Service Indicator (SIN). The SIN is used to determine if the call is voice, fax or data. It's essential to set

Hi. I'm looking at ordering a 30-channel ISDN connection from telia (a swedish operator) and then using a Wildcard TE110P card with that and asterisk to do IVR. Can I be certain that the TE110P card will work with that ISDN connection? A 30 channel ISDN certainly sounds like an E1 connection, but I couldn't get any clear answers from the operator if it is. Has anyone used the TE110P

Hi again folks! ;) As before, I will transform one E1 30 Channel PRI into 30 FXS channels using Adit 600. Now I'm into choosing server platform. And the two opponents are: * Dell PowerEdge 750 w/ SCSI RAID (or even SATA RAID1) * FujistuSiemens PRIMERGY RX100 S2 (SATA RAID1) As I've seen people having problem with HP server, I havn't looked at it at all. What experience do you

Are there much performance differences when using XEON or not? In my case, I will go with muLaw both in and out of Asterisk. Are there really any processing at all if it's using same codec all the way?

Hello, I am relatively new to Asterisk and I need to compile the G.723.1 codec for Asterisk. I downloaded the ITU source code, placed it in the codecs directory, but apparently Asterisk needs a rather different library than the one provided from ITU. As I've seen in the mailing list archives, there are quite a few users who were able to compile G.723.1 in *, so, could someone kindly share it

Hi folks! Our company are going to buy an E1 line with Euro ISDN and 30 lines (channels). This is how it will be configured: 3 Lines, of the total of 30, is going to be for the company phones, and share one phonenumber (eg. 555-12340). 1 Line will be dedicated to a specific unique phonenumber (Fax) (eg. 555-54321). The rest of the lines/channels (26) will be used by (by, not for) our customers,

A new RFC was published today, RFC 3601: Abstract: "This memo describes the full set of notations needed to represent a text string in a Dial Sequence. A Dial Sequence is normally composed of Dual Tone Multi Frequency (DTMF) elements, plus separators and additional "actions" (such as "wait for dialtone", "pause for N secs", etc.) which could be

I'd be grateful if anyone here could comment knowledgeably on an idea that I have had, as to whether it should be possible or not. Consider two Asterisk boxes, each with one or more E1s on EuroISDN. Each box has a different telephone number that hunts across all its E1 channels. In addition there is another number that hunts across all the channels on all the boxes. A call comes in to one of

I am trying to use TE110p card for Euro ISDN with Ericsson AMS switch. I consistently get one of the following errors: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 or PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 My zaptel.conf file: -------------------------------- span=1,0,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=us defaultzone=us

We've got a EuroISDN (32 channels) with a TE405p, running cvs head as of 5 days ago. In the past couple of days, we've hit a scenario where incoming calls to the * pbx from the PSTN are being marked as busy, but outgoing calls work just fine. When we reboot *, the problem goes away. Has anyone else had this ? I've attached a PRI debug below. I've changed the phone numbers (x

Hi all, We're trying to hook up our Asterisk config (Card: TE410P) with a Siemens EWSD switch. The link is ok on both ends (green), with no errors. The problem is when we try to make a call from our side (via call files), we get the pri/E1 error Ext: 1 Cause: Temporary failure (41), class = Network Congestion (2) Our Telecom partner (they checked with Siemens) mentioned that we need to

I'm trying to use ZapRAS to enable ppp connection through my E1. After the ZapRAS command is executed, all sound is crappy on all lines! The only solution is to reboot the machine (or halt it, and then power it on since Digium's hardware doesn't like reboots). Anyone know how this can happen?! I'm using * 1.0.6 on Dell PowerEdge 1850 which are told (too late though) not to work

We are not having any luck with the E100p card here in Australia, it will work with a crossover cable to another device but will not talk to our Telco Telstra who probably have a weird implementation of an E1. Any suggestions on a replacement? Regards Mark McKibbin DCS Internet 64 Queen St Warragul Victoria 3820 Australia www.dcsi.net.au mark@team.dcsi.net.au Ph. 1300 665575 Fx. 1300 556595

Hi All, I've bought a R2Adapter to convert R2Digital to ISDN. I am trying to config E100P card but D-Channel is down. I know R2Adapter uses ETSI ISDN Protocol so I tried unsucessfully setup switchtype to EuroISDN. Any clue? Daniel

Hi, I have installed Elastix 1.5.2 (Barranquilla, Colombia (TELCO: METROTEL)) with a TE220P (2xE1) and TDM2400P (16FXS), openr2 is included in 1.5.2 version. The outcoming calls are ok, but with incoming call i have an error: ERROR*[*14972*]* chan_dahdi.c: Chan 2 - Protocol error. Reason = Multi Frequency Cycle Timeout, R2 State = Seize ACK Transmitted, MF state = Category Request Transmitted,

Hi, I have a problem with dialling internationals numbers, and I don't now what is the cause. I have one asterisk with a e100p card connected to the Telco (spain/telefonica) and it can dial local and national numbers without problems but when I try to dial a international number it hangs-up. I call the Telco to ask if the E1 can do international calls and it said that it can. I have tried

Hello, Configuration: Asterisk CVS HEAD 20050730 on RH EL3+ DIGIUM TE110P PRI card + euroISDN E1 I am trying to sort out the problem: 1. Provider's switch sends "SETUP"; 2. Asterisk receives "SETUP", rings allocated extension but does not send "Setup acknowledge" (or any other messages) to switch; 3. After 4 seconds of waiting of *'s response switch sends

Hi, Hey people, i have a TE210P with a ISDN PRI in M?xico. It is working just fine with Asterisk, I just have a minor glinch. When I dial a number that doesn't exists the Zap channel is imediatly hungup, instead of putting my trougth the providers message: "Sorry, the number that you dialed does not exists, etc". I have a call center and the people there really need to be able to

Hi, since version 1.4.12 the libpri package supports ETSI Explicit Call Transfer feature: http://downloads.asterisk.org/pub/telephony/libpri/ChangeLog-1.4.12 Does anyone know, how to use this feature in the dialplan? I can not find any hints in the asterisk doc. Best regards, -Thorsten-