similar to: Cannot reset an IAXy box!!!

I'm having some problems with a bunch of older IAXy devices. I have three S100I devices working. I can call each device from each other and everything works perfectly. When an inbound call comes in (from PSTN) and is routed to the device, it works perfectly as well. The problem is that when I place an outbound call (to PSTN), the remote party can hear me well, but I cannot hear the

I place a call from an IAXY to an IAXY device. INitially the calls show in the output of "show channels". Then after a few seconds the "show channels" command shows 0 active channels even though I am still talking on the channels. Any ideas on this? THanks, Jerry

Hi.. I have to setup an extension in a remote location that will use a cordless analog telephone.. I am looking at the IAXY to do this for me..Basically the data path will be as follows... [Asterisk] == (NAT) == {Internet} == (NAT) == ATA -- Handset Since there are two NAT boxes in the path I know SIP won't work.. I also don't want to move the Asterisk box to the internet side of the

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

Hi, I've got an IAXy, and provided it with connection data - unfortunately didn't provide a fixed ip address, but left with dhcp. Everthing went fine, and I could work a while with it. After a restart of IAXy, it didn't negotiate a new IP address, nor used the old one. I even restarted the DHCP server and cleared its cache. No success. I went to another office with a different

Hi, I have three Iaxy devices (s101i) parts. Two of them seem to work fine. The third plays a loud repeating click sound when an analog phone is plugged in. I can provision all of them, and make calls to all of them. The clicking one will blink when a call is incoming, but no audio from the call can be heard on the handset, and the caller only hears silence. The same handset works on the

I can't seem to get this device to grab an ip from dhcp. We have a working dhcp server (unfortunately it is on Windows), but I don't show any leases requested by the iaxy. Anyone have any ideas? The ethernet and phone lines are plugged in before the device is powered. Thanks, Erik

Hi all, I have a Soekris net4801-50 board with OpenBSD 3.9 where I've configured a dhcp server and tested it with a regular PC connected directly via a crossover cable with success. The problem comes when I try to connect my IAXy device instead of the PC. I can see with 'tcpdump -nettti sis1' that the IAXy isn't sending any packets to the dhcp server. I thought my IAXy was bad

In the mailing list archives, I found a message that indicates that the IAXy has the ulaw, alaw, and g726 codecs, but I cannot find anything official on Digium's site about it. The Installation Manual has an example iax.conf file that indicates the ulaw codec, so I know that one is good. But we are thinking about using the IAXy over a VPN, to replace our MultiVoip. alaw and ulaw are

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04:

I'm having a problem with my IAXy not always connecting to my Asterisk box. When I pick-up the phone plugged in to the IAXy I get a busy signal. I have to hang-up the phone and wait a few seconds after the orange LED goes out and then try again. When this happens I don't see any connection attempts in the Asterisk -r output. When I do get the IAXy to connect to Asterisk I get a

Hi, Has anyone got faxing working via an IAXy? I'm having trouble getting it working with a fax machine here. The IAXy works fine, I can make incoming/outgoing calls via it, however our PDQ takes a few redials to get data over to the dialled party, and faxing doesn't seem to work at all. I have turned off all the echo cancellation stuff, just in case that was an issue. Anything I

In features.conf, I have uncommented the transfer features under feature map, but I still cannot transfer using a POTS phone on an IAXy adapter. I think I am missing something here.... Any help is appreciated. Here is features.conf: ; ; Sample Parking configuration ; [general] parkext => 700 ; What extension to dial to park parkpos => 701-720 ;

Ok, I searched the lists and found no definitive answer. I'm assuming the IAXy has some primitive form of echo cancel, is there anyway to adjust this? Or any ideas on what to do instead. Here's the setup, this will not be a typical setup for our company however, well whatever. Anyway it looks like this: IAXy --> Netgear router --> Charter --> Level3 --> Asterisk --> VOIP or

I am having trouble with a DTMF-based application on Asterisk 1.0.3. Specifically, when two IAX2-based devices are talking, when they send DTMF to eachother, the other side only hears clicks, and maybe a millisecond of DTMF tone, but not any real duration. Furthermore, when one IAXy device calls the Echo test program, we can hear our echo, but when we punch DTMF in, we get the same effect

Hello All, I have an iaxy(new version), and while it does the job well, there is one thing I am looking for. I want to be able to specify a dns name on the config, not an ip. This does not seem to work if I try to set it as such. Has anyone come up with a workaround or solution to this? I want to be able to put it on the net, or travel with it, plug and go. The issue is that I am using a

I've got a single IAXy installed in a little office nearby and got a call from someone on site a finew mintues ago. Apparently they couldn't make a call on that extension. They'd pick up the phone and get nothing; no dial-tone. Running "iax2 show peers" showed the unit still registered and I could ping it too. Didn't try to call it while it was doing this; sorry. The

Yesterday I was using one of the cheap Radio Shack phone polarity on various phone outlets in my house and ended up plugging it into my IAXY. While the regular phone jacks tested OK, the IAXY tested as being reverse polarity. The tester was plugged directly into the IAXY so there is no chance of this being caused by crossed wires. Is this something that is misconfigured on the IAXY, a hardware

iH i have an IAXy which i can make calls from but am unable to call. when i dial the extension assigned, i get the following from the console; -- Executing Dial("SIP/5801-b665", "IAX2/5899@192.168.0.5") in new stack -- Called 5899@192.168.0.5 -- Call accepted by 192.168.0.5 (format ULAW) Nov 1 12:28:33 NOTICE[163850]: chan_iax2.c:5546 socket_read: Rejected

Does anyone know a place in Australia that sells a power supply suitable for the IAXy? I haven't had any luck tracking one down. -- jeremy bogan [ jeremy@segpub.com.au ] segment publishing - design.develop.host