similar to: Problem using TDM400P FXS card

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

As best i could figure it out, I've installed dahdi and rc4. My TDM400P doesn't answer fxo or fxs. /etc/dahdi/system.conf: loadzone = us defaultzone=us fxoks=1,2 fxsks=4 /etc/asterisk/chan_dahdi.conf: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1 ;

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

I have seen mention of limiting a single server to no more than 100 trunks. With Sangoma having an 9 T1 card that kind of blows that limit. How many T1's can we have on a single server assuming dual Xeons? Our application calls for 122 IP Phones and 120 analog ports for faxes. Its an executive suite and we need the fax ports. No way around that requirement. Thanks, Allen.

This is, hopefully, just a case of brain fade. With zapata.conf and zaptel.conf in place, asterisk loaded, no dial plan and all LEDS on the card lit, I get no dial tone, plugging an analog phone into ports 1 or 2, only a buzz and click. zaptel.conf - defaultzone=us loadzone=us fxoks=1,2 fxsks=3,4 zapata.conf [channels] signalling=fxo_ks language=us context=phones-1 group=0

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

Hi, I'm installing an Asterisk box with a TDM2400P in Brazil. I can make analog phones work while lines are not working. Since I do not know anything about brazilian lines, is there anybody who can tell me what is wrong/missing in my conf files (below)? TIA Giorgio _zaptel.conf:_ fxoks=9-16 fxsks=17-24 defaultzone=br loadzone=br* * _zapata.conf:_ context = inbound_zap echocancel = 128

I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]

Has anyone got a sensible zaptel.conf and zapata.conf for 2 TDM400P's working with UK set-up. They're set-up with 7 analogue phones and 1 PSTN port. Currently zaptel.conf has fxoks=1-7 fxsks=8 loadzone=uk defaultzone=uk It's really zapata.conf that would be useful. Currently using the zaptel/asterisk that comes with Ubuntu (latest) which needed a bit of tweaking (1.2.16), but could

I have seen this in the archives any number of times -- but I have yet to find a solution that works for me. Any suggestions you can offer would be most appreciated. Here are the answers to the questions I have seen asked in earlier posts. The log contains: Mar 10 12:26:29 WARNING[3015] chan_zap.c: Unable to specify channel 4: No such device Mar 10 12:26:29 ERROR[3015] chan_zap.c: Unable

Hi list, I've just compiled and installed Asterisk 1.4.16 and when I try to run "zap show" I get the message "*No such command 'zap show'*". I have a Sangoma Remora A400D with 2 FXS / 10 FXO ports, I've installed the latest wanpipe too. zaptel-1.4.7.1 was compiled from the wanpipe installation, so I don't know what's happening here!!! Any ideas???

can somebody that has these hardwares(X101P and S400P) working on his asterisk system please assist.................. you can send the solution to austino@skannet.com..... the error message is what i have below. ---------- Forwarded message ---------- Date: Thu, 1 May 2003 21:01:21 +0100 (WAT) From: austino@skannet.com To: asterisk-user@lists.digium.com Subject: Error working with X101P and

We just bougth a tdm2400p with all the modules for FXO, but we are having some troubles with the card, cause it aparently is stripping some digits from the dialed number, we tested the same server with a tdm400 and everything worked as expected. We?ve already added "w" before the dialed number with no results, is there any way to solve, is it a bug thanks

Please explain the relationship between modules from the driver (wctdm), the /etc/zaptel.conf file and zapata.conf. Specifically, if I have a FXS module 0 and FXO module 1, what should be used in zaptel.conf and what should be used in zapata.conf? Then finally, in extensions.conf, what is the Zap channel for dialing out? Zap/? % dmesg Module 0: Installed -- AUTO FXS/DPO Module 1:

I have just received a T100P and an Adtran TSU 600 in the mail. I seem to be having a problem with the T100P card. So far I have done the following: vi zaptel.conf fxoks=1-22 fxsks=23-24 ... vi zapata.conf ... signalling=fxo_ks ... channel => 1-22 ... signalling=fxs_ks ... channel => 23-24 I then run modprobe zaptel modprobe wct1xxp ztcfg -vv There are no errors to report. In

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

I'm having a problem defining my channels Here is my zapata.conf ----------------------------------------------------------------------------------------------------- ; Zapata telephony interface ; ; Configuration file [channels] ; rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes

Looking for some help from the UK please. I backed up all my Asterisk configuration before re-installing the server from 32 -> 64 bit. Unfortunately I did not transfer the backup to another machine!!!!! I now have a TDM400P that is not picking up the line. Can you see what I have done wrong when I have rebuilt the config please: dahdi_scan ---------- [1] active=yes alarms=OK