similar to: TDM400P FXS works only if two lines are off hook?

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905

I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when

Hi, I've been avoiding investigating this issue for a while; I used to revert to a previously compiled version of zaptel & a previous kernel (as at some point I think I stopped being able to compile the older zaptel against the newer kernels) and all was well. However I've now upgraded kernels again and it seems silly to hide from the problem - here goes, let's try and fix it! At

I apparently have a dead FXS module. Is there any kind of test I can run on it (on a live system) to determine if its good or bad? The telephone has no dialtone, gets no calls. It has been working for several months, and just quit yesterday. Thanks! Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

Hi, I have a TDM21B (A new TDM20B that just arrived plus a X400M that I already had). This card sometimes works, and sometimes only the FXO module is seen. By "works", I mean all 3 modules have the green lights on the ports on and when zaptel is loaded the log shows: Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi all, I was wondering if anyone had any pointers on how to determine whether or not a module has gone wonky on the TDM400P? I have a 2 FXO (channels 3 and 4) and 2 FXS unit (channels 1 and 2). The bad (?) module in question is the FXO module on channel 3. I can't dial in to or out of that channel; dialing in gives a busy signal, dialing out just shows * hanging around after attempting a

I have an asterisk 1.2.9.1 machine with zaptel 1.2.6 running. On the TDM400P, I have 1 FXS port and 3 FXO ports. dmesg reveals: Zapata Telephony Interface Registered on major 196 Zaptel Version: 1.2.6 Echo Canceller: KB1 PCI: Found IRQ 10 for device 01:01.0 PCI: Sharing IRQ 10 with 01:05.0 Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hello, I have few questions about Asterisk. I installed Asterisk from CVS on FreeBSD and I made cvsup 2 days ago. 1.I couldn't find Asterisk version using "asterisk -V" command. How can I to find version information? 2.I am using Wildcard X101P (FXO) and Wildcard TDM400P REV E/F (FXS)on it. I tried Asterisk CallerID feature, but unable to get it. I tried callerid signaling V23,

Hi, I recently installed a gentoo on a PC, purchased a TDM400 and installed asterisk. Kernel is 2.6.11-rc3 First, there seems to be a problem with my system: I must put the pci=routeirq to make the card detected. The modules are loaded ok (dmesg output) Zapata Telephony Interface Registered on major 196 ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 16 Freshmaker

Hello, I have few questions about Asterisk. I installed Asterisk from CVS on FreeBSD and I made cvsup 2 days ago. 1.I couldn't find Asterisk version using "asterisk -V" command. How can I to find version information? 2.I am using Wildcard X101P (FXO) and Wildcard TDM400P REV E/F (FXS)on it. I tried Asterisk CallerID feature, but unable to get it. I tried callerid signaling V23,

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output

Hello, everyone After having spent several time to look for any solution for my problem, I decided to write here. Here is the problem got a Digium X101 FXO card and Digium TDM400P alias freshmaker (1 fxs module on it on first port ) in my asterisk box. The X101 works perfectly. The problem comes from the TDM400, when i plug a tested working phone on it , i get no dialtone; the goal is to

I got this nice TDM22B with two green modules left and two modules right /var/log/messages shows: Nov 26 23:47:48 dns kernel: Zapata Telephony Interface Registered on major 196 Nov 27 00:37:53 dns kernel: Freshmaker version: 71 Nov 27 00:37:56 dns kernel: Freshmaker passed register test Nov 27 00:37:56 dns kernel: Module 0: Installed -- AUTO FXS/DPO Nov 27 00:37:56 dns kernel: Module 1: Installed

I got this nice TDM22B with two green modules left and two modules right /var/log/messages shows: Nov 26 23:47:48 dns kernel: Zapata Telephony Interface Registered on major 196 Nov 27 00:37:53 dns kernel: Freshmaker version: 71 Nov 27 00:37:56 dns kernel: Freshmaker passed register test Nov 27 00:37:56 dns kernel: Module 0: Installed -- AUTO FXS/DPO Nov 27 00:37:56 dns kernel: Module 1:

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1