similar to: how to add more TDM04B

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

Hi all, I've struggled for several days trying to get a Digium TDM04B 4-port wxfco card working on a Dell 1U PowerEdge 750 machine running Fedora Core 1. I finally got a call back from Digium who indicated that there is a fundamental conflict between the card and the PowerEdge having to do with PCI interrupts. Asterisk version is stable v1-0 12/29/04. The symptoms of the problem were as

Hello, my first post to the list. I have started to install and play with Asterisk. I was following some basic instructions to 'jump-start' my system. I have a TDM400P with one port and a X100P. I am running the latest CVS versions (from today). Following the steps I found for basic jump-start I did the following: Modprobe zaptel Modprobe wcfxo Modprobe wcfxs Edited

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

Hello, I ordered the Devel lite kit, and installed it. I am just trying to get the FXO port to work, and am having trouble. To load the card I do the following. modprobe wcfxs modprobe wcfxo ztcfg -vv asterisk -vc My /var/log/asterisk/messages show Nov 3 11:03:39 WARNING[3317]: zt hook failed: Device or resource busy Here is my /etc/zaptel.conf fxoks=1 fxsks=4 loadzone=us defaultzone=us

Need some help with modules.conf, and basic RH9 linux skills. I've installed the new TDM04B 4-port FXO card and its working. After a reboot, when I do lsmod I see the wcfxo module but not the wcfxs even though both are listed modules.conf. If I "modprobe wcfxs", then lsmod has both modules showing. The wcfxs module is the last one in the modules.conf. Is the order of entries

Hello I am (attempting) to run the astlinux version of Asterisk on a VIA embedded platform. I have a TDM04B and pretty sure zaptel.conf and zapata.conf setup OK. They worked fine with same card in traditional PC anyway. I think need the module wcfxs for a Digium TDM04B card. Is this module not part of astlinux? Do I need to download it? Or is it in opt? I see wctdm - but think that is

Hi all i need urgent help our entire switchboard is down only 5 days after it came up. this is the second time this has happened and i am thinking that asterisk is not worth the trouble it gives. mostly it runs without hassle. but around 2 weeks ago during the test phase we rebooted the machine and did the normal modprobes and this error popped up. coming back to work after the weekend the

I installed TDM400P and X100P pci cards in a system running mandrake 10.1 official, kernel 2.6.8.1-12mdksmp. I can compile zaptel, libpri, asterisk and modprobe (zaptel, wcfxs, wcfxo) without errors. Except that running ztcfg and asterisk fails. [root@asterisk asterisk]# ztcfg Notice: Configuration file is /etc/zaptel.conf line 3: Unable to open master device '/dev/zap/ctl'

All, I'm having trouble getting the X100P working. Lsmod shows : zaptel 179808 0 I did a . # modprobe zaptel and here is my zaptel.conf (comments omitted) __SNIP__ fxsks=1 loadzone = us defaultzone=us __SNIP__ Here is zapata.conf __SNIP__ [trunkgroups] [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 usecallerid=yes hidecallerid=no

Hi: I had an fxo card from Digitnetworks and it was working fine on my Asterisk box. I then replaced it with TDM04B. I changed the zaptel and zapata to include the four channels. When I run ztcfg, I get configuration errors: Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04:

/bin/sh: -c: line 0: syntax error near unexpected token `;' /bin/sh: -c: line 0: `if [ -n "" ]; then if [ -f ]; then mv -f .bak ; fi; cat .bak | grep -v "alias char-major-250" | grep -v "post-install torisa /sbin/ztcfg" | grep -v "post-install wcfxsusb /sbin/ztcfg" | grep -v "alias wctdm" | grep -v "post-install wctdm

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo

I haven't seen anybody so far post a complex fix for the udev problems on FC3 with the latest kernel. On that note, I have a temporary fix to allow zaptel to load somewhat normally. I found that modifying the zaptel script to 1) load, unload, then load the driver modules and 2) insert a pause between modules seems to allow things to work. This assumes you have followed the instructions

Hello, I'm running Fedora Core 3 with udev, and asterisk/zaptel/libpri from cvs. I have followed the README.udev instructions replacing insmod with modprobe and rmmod with modprobe -r and adding the 60-zaptel.rules file, yet no matter what I do I still get this error on boot(or when I run service zaptel restart): [root@pbx ~]# /etc/init.d/zaptel restart Unloading zaptel hardware drivers:

I have the same problem in a box with 2 HFC-PCI, but i already remove the row in modprobe.conf and load the module manually. Both cards works fine Any idea ? Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Julian J. M. Inviato: luned? 27 giugno 2005 12.04 A:

Hi guys, Thanks for your answers on my two questions yesterday. That's exactly what I was looking for, sorry for not noticing it myself, but I'm still getting acclimated to Asterisk and even Linux--from what I see so far, I love it. I've got another one now. Since my Asterisk install and configuration is fairly stable at this point, I'm interested it ensuring that during

I found similar posts regarding this error but none that answered my question. My zaptel.conf reads: fxsks=1-2 fxoks=3 loadzone=us defaultzone=us and /proc/interrupts: CPU0 0: 5542402 IO-APIC-edge timer 1: 2 IO-APIC-edge keyboard 2: 0 XT-PIC cascade 8: 3 IO-APIC-edge rtc 14: 72582 IO-APIC-edge

Thanks in advance root@asterisk01:~# modprobe wcfxo /lib/modules/2.4.20/misc/wcfxo.o: init_module: No such device /lib/modules/2.4.20/misc/wcfxo.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20/misc/wcfxo.o: insmod /lib/modules/2.4.20/misc/wcfxo.o