similar to: where to buy x100p

Hello, Which port Smb4K uses? I am not able to use Smb4K on my server for the local network. Thanks Varun

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. My default shorewall settings are : Source zone Destination zone Policy Syslog level Traffic limit loc net ACCEPT None None fw net ACCEPT None None net Any

I'm looking to get an x100p off ebay and am not particularly familar with the "life cycle" of the card.. An "Authentic X100P" listing has a buy it now of $29.95 and says There are 3 types of cards Asterisk would recognize: *Screenshots from the official, original driver install Cheap "OEM X100P","Clones", "Compatibles", Knock-Offs

Hello, Since FC3 has been a very recent release I was just wondering if there are issues related to asterisk installation on FC3. Thanks Varun

Hello, I want to block a particular IP on the local network. Howto do that ? Thanks Varun

Hello, Are there any issues with Centos 4.4 and asterisk. Thanks in advance Varun

Hello, > My server is on Mandrake 10.1 off. > eth0 is WAN with static IP connected 512 DSL > eth1 is LAN. I am little confused about NAT. I have a static IP from ISP I want to do a NAT on eth0. What should I use in shorewall masquerading or static nat ? Thanks Varun

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. I have NAT working on 192.168.0.0. I want to feed a second subnet 192.168.21.0. What is the best way to implement it ? Thanks Varun

Hello, > My server is on Mandrake 10.1 off. > eth0 is WAN with static IP connected 512 DSL > eth1 is LAN. I need a little clarification on static nat settings in shorewall. external address - static IP internal address - ? for the internal address should I put my eth1 IP or the general subnet range. For example 192.168.0.0. I am also not sure about : Active for firewall system? yes

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. I have enabled shorewall and it has blocked access to the net on my server. My default shorewall settings are : Source zone Destination zone Policy Syslog level Traffic limit loc net ACCEPT None None net Any

Hello, I have an onboard sound AC97. Howto to find if my sound is full duplex ? And if my sound is not full duplex then please recommned me a good full duplex sound card that is supported on linux. Thanks varun

Hello, Is it possible to use v92 ( a few chipsets version ) modem as FXO PCI modules ? While googling I found some postings on the subject. Thanks Varun

Hello, I am not able to use ftp and ssh on the lan. Both the port are open. I have the lines on the rules file : # Accept SSH connections from the local network for administration # ACCEPT loc fw tcp 22 # # Accept ftp connections from the local network for administration # ACCEPT loc fw tcp 21 Thanks in advance Varun

Hello, My server is Mandrake10.1 eth0 is WAN with static IP eth1 is LAN I would like all traffic from 2 client - 192.168.0.253 and 192.168.0.248 on the lan to go straight to outgoing interface. I am not sure whether to use DNAT or ACCEPT. Can anybody clarify ? Thanks Varun

Hi All, Sorry if this has been around a millions times.. I have been off this list for a few months now.. I have installed the latest asterisknow (upgraded asterisk to 1.6 as well) and I am having a hard time getting my X100P and TDM400P working.. Its all new to me with dahdi because my old server is still running Asterisk 1.0.2 so there have been lost of changes.. Can someone point me in

Using TDM400's here and I have tried everything to cure the echo. I have used the Milliwatt test from the telco and from asterisk to tune RX/TX gain via a patched ztmonitor. What happens is I experience midcall echo. I turned on aggressive_suppressor and it seems to do great. The problem happens with misc. noise around the office will cause it to mute the other end of a phone call while

Since the X100P/X101P/Clone cards does not work in all countries that use DTMF based Caller-ID systems, I've developed a hardware that you connect to a serial port and the PSTN. You then run a perl script "cid_logger.pl" as a daemon, and modify extensions.conf to call an agi script whenever a call comes in, and if it's on the X100 card it will get the caller id information

Hello, How good is :SPA 841 form SIPURA. Thanks Varun

Hello, I am not able to open the webmin web interface on my server. Shorewall is blocking it. How to allow it on the server. Thanks Varun

I have a bad echo problem on my TDM400P with one FXO module installed. I have tried a few things, such as: * setting rxgain and txgain to 0 * setting echocancelwhenbridged to no / yes * settting echocancel to 64 / no / yes * setting echocanceltraining to 800 / no / yes * MG2 echo cancellation * MARK2 echo cancellation * KB1 echo cancellation * AGGRESSIVE_SUPPRESSOR option of MARK2 Each time