similar to: Bristuff ZapHFC and Loosing D-Channel

Displaying 20 results from an estimated 2000 matches similar to: "Bristuff ZapHFC and Loosing D-Channel"

2006 Jan 14
4
Ugly echo cancel, with Bristuff/Zaphfc
I'm using bristuffed Asterisk with ISDN/ZAPHFC I have VERY ugly (outgoing) sound through ISDN/HFC if echocancel=yes in zapata.conf, but without echocancel I have bad (incoming) echo Through PSTN/FXO sound is ok with or without echocancel. I tried other echo cancellers (in zconfig.h) two times: ECHO_CAN_KB1 (this was default) ECHO_CAN_MARK2 ECHO_CAN_MG2 after any change I compiled (make
2005 Jan 23
4
Florz patch for zaphfc
Has anyone had any success using the Florz patch for zaphfc ? I have a * system with 2 HFC cards which is working fine with 2 PTP ISDN lines however the users are complaining of crackles on the line which I am assuming is related to the IRQ issues raised by Florz. I have tried to use the patch but it errors trying to patch zaphfc.h Any help would be appreciated. Regards, Stuart -- No virus
2005 Sep 23
1
zaphfc problem: overlapdial don't work after update bristuff
hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode
2005 May 25
7
zaphfc: empty HDLC frame or bad CRC received
Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from
2005 Feb 13
1
bad sound ISDN bristuff
Hello * users I've problems with sound quality on zaphfc Asterisk works fine good sound quality. If I do "make load" in the bristuf.xx zaphfc dir then sound quality drops directly. Even if I don't load the chan_zap in the modules.conf I use this config on more (even old 400Mhz machines) and works correctly. Looks like an hardware problem but I can't find it. I don't
2005 May 31
1
rxfax application - doesn't work properly
hi, I am on fax-to-email system, basically taken from http://www.voip-info.org/wiki-Asterisk+Fax+to+email well, it seems that asterisk causes some problems so that it is impossible to send any fax. I.e. when I try to send a fax to asterisk (rxfax application): normalFax--->FXS(TDM400P)--->Asterisk(RxFax) it breakes up the trasmission at the beginning of sending page. The code given by
2006 May 10
1
ISDN Bridging with Bristuff
Hello, I tried to read Bristuff source code to understand the way calls are bridged from one BRI port to another (as HFC cards have "active channel switching capability"). Doing so I looked at zaphfc.c file which seems to be the only .c file constituting bristuff but I may be wrong I'm far from being an expert on this. I found 4 functions (hfc_btrans, hfc_brec, hfc_dtrans,
2005 Aug 16
2
florz patch for bristuff breaks compile on x86_64?
After upgrading a CentOS 3.x box to CentOS 4.1 (both x86_64 with an Athlon64) I also wanted to get the latest bristuff. Unfortunately bristuff without florz causes the box to kernel panic within hours (console will complain about bad frame received something). It seems however that the florz patch will not work for x86_64 arch. Bristuff -0.2.0-RC8j compiles fine without the florz patch, but
2006 Jan 15
2
RX/TXgain on bristuff/zaptel ?
Do bristuffed zaptel (zaphfc) supporting rxgain/txgain in zapata.conf? I'm changing rxgain in zapata.conf, and reloading zaptel, but sound level on ISDN(HFC) is always the same (loud).
2005 Mar 08
2
zaphfc error
I have some problems starting asterisk with a hfc card using zaphfc: [chan_zap.so]Mar 8 17:53:06 WARNING[2447]: loader.c:258 ast_load_resource: /usr/lib/asterisk/modules/chan_zap.so: undefined symbol: ast_retrieve_call_to_death Mar 8 17:53:06 WARNING[2447]: loader.c:391 load_modules: Loading module chan_zap.so failed! I'm using asterisk from debian/sid: Asterisk
2005 May 18
6
zaphfc troubles
Hi, I'm trying to setup a small BRI ISDN <-> voip gateway. The ISDN card is based on Cologne chipset, so I try set it up with zaphfc. The versions i'm running: kernel-2.4.27 Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e zaptel modules 1.0.7 zaphfc is from bristuff-0.2.0-RC8e When I'm doing the insmod on zaptel, zaphfc, zaprtc: Zapata Telephony Interface Registered on major 196 PCI:
2005 Jan 09
1
Can zaphfc (bristuff) do caller id?
Caller id is not in the configs that are supplied with zaphfc from bristuff, and it's not mentioned in the wiki. Is it possible to use callerid with zaphfc/bristuff? Thanks!!
2004 Dec 06
3
Recomended ISDN for Asterisk ?
Hi I have installed the http://asteriskathome.sourceforge.net/ with a Digium card with no problems, very good ! Now I want to install my Billion PCI ISDN card (HFC based) in TE mode. I get a little confused with Isdn4Linux, ZapHFC HIAX and the need to install Capi ! Please suggest best and easiest approach ? Thank you ! HB Norway
2006 Jan 05
1
bristuff/zaphfc disturbing other ISDN phones
I have ISDN BRI line (Point-to-multipoint), with HFC card and bristuff/zaphfc driver. I also have TA attached to NT, with analog phones and modem on it. When I'm dialling through Asterisk/bristuff, and in the same time TA have some conversation (or maybe modem link) on channel 1, I can hear that conversation (or modem) very short period (0.2sec), and I also disturbing that conversation
2006 Nov 16
1
zaptel, bristuff zaphfc, and florz question
Hi, We've been using zaphfc single ISDN cards as cheap Zaptel timing sources for our Asterisk boxes for a long time, and in the asterisk 1.0.x series, had zero problems doing so. I now have some boxes with Zaptel 1.2.x (with a mixture of 1.0.x asterisk and 1.2.x asterisk), and this setup no-longer seems stable - By plugging or unplugging the ISDN cable, and sometimes just randomly the card
2005 Jul 16
1
Multiple ISDN BRI Units with Asterisk using Bristuff zaphfc in NT mode?
Maybe this is rather a hardware question, but I am posting it on this list because the probability of someone else of you having tried this is greater here than other places I can think of. I have an ISDN card that is setup in NT mode using the zaphfc driver in bristuff, and I got it working perfectly with one ISDN phone using a crossover cable and 100 ohm termination at the end of the cable.
2004 Mar 18
4
zaphfc problem
Hi, I have a partial working installation with zaphfc. Incoming call : For incoming call, seems work fine. But the sound is very bad with bounce short crashing sound. Same sound with echo cancel off or on. SDA work fine. Another problem, it's seems that's zaphfc don't reset correctly the line. I have one of my D channel how was busy even after stop communication. Outgoing call :
2006 May 09
6
Bristuffed Asterisk: Hangup problems
Hello, I have a problem with the Bristuffed version of Asterisk. I have tried Bristuff-0.3.0-pre-1m,n,o,p (Asterisk 1.2.6 to 1.2.7.1) but they all have the same problem it seems: The setup: A machine with a single hfc-s PCI BRI adapter running Gentoo 2.6.15. Asterisk 1.2.0 (BRIstuffed-0.3.0-PRE-1) installed and working perfectly. Grandstream gxp-2000 as a SIP phone, and a normal mobile
2006 Jan 06
0
Bristuffed asterisk 1.2.1 on Suse 10 - problem with zaphfc module
Hi, I'm banging my head on compiling bristuff modules for Suse 10.0 with kernel : Linux laps1 2.6.13-15.7-smp #1 SMP Tue Nov 29 14:32:29 UTC 2005 x86_64 x86_64 x86_64 GNU/Linux and Asterisk 1.2.1-BRIstuffed-0.3.0-PRE-1f . I get this : laps1:~/Voipy/1.2.1/bristuff-0.3.0-PRE-1f/zaphfc # make load make -C /usr/src/linux-2.6 SUBDIRS=/root/Voipy/1.2.1/bristuff-0.3.0-PRE-1f/zaphfc
2006 Oct 26
1
chan_capi and bristuff
Hi, Reading from www.voip-info.org, i can see that "Junghann's chan_capi is now part of bristuff <http://www.voip-info.org/wiki/view/Bristuff> , as of version 0.3.0-pre". What does that really mean ? Shall I understand I can share a Junghanns QuadBRI board between 2 CAPI-enabled software (like a 0.3.0-pre bristuffed Asterisk for instance) ? If positive, what are the pros and