similar to: PRI dchannel in use? (take 2)

I just started getting this error and its preventing me from having any incomming calls: chan_zap.c:7542 pri_dchannel: Ring requested on channel 0/2 already in use on span 1. Hanging up owner. PRI has been working fine. I didn't know anything was wrong until someone came and said their DID wasn't working. You call their DID, asterisk shows the message above and you get fast busy. But I

Hi fellow asterisk users, I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel module) an approx. 100 snom320. The whole installation is running without issues since 5 months. Without having changed anything on the asterisk server for at least 2 months, i noticed "clicking sounds" at external calls over the PRI. Asterisk constantly throws the following messages: ...

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

Hi, I am getting this message on the * console on my first pri span. Pri show span show it is down, and I can't make any calls from the span. Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27

hello all, i'm using TE110P and all configuration prosess is done. but after i do the 'modprobe' for zaptel and wcte11xp, follow by ztcfg -vv and asterisk -vvvgc i have this error. *CLI> May 27 14:44:33 WARNING[3059]: chan_zap.c:8534 pri_dchannel: PRI Error: We think we're the network, but they think they're the network, too. May 27 14:44:34 WARNING[3059]: chan_zap.c:8534

I've read as much as I can on this error and still can't seem to figure out what's causing this error: Jun 23 20:54:58 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Jun 23 20:55:03 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Jun 23 20:55:03 NOTICE[7483]:

I am trying to test out my PRI configuration on a server by conection another asterisk server to it. I have the T-1 cards up and both set to bchan=1-23 and dchan=24 in zaptel.conf I am getting lost on the signalling in zapata.conf. using pri_cpe makes sense for my target box, but I am getting the following errors on my source box if I use pri_net or pri_cpe signalling. May 31 17:15:06

Hi all, So, we reverted the LibPRI version and tested it, and then tried with the latest version of everything. Still no changes. The BRI line is in PTMP. If we set the configs to PTMP in the genconf_parameters and try it, we get the following: [Jan 21 17:32:20] ERROR[20341]: chan_dahdi.c:12645 dahdi_pri_error: Unable to receive TEI from network! If we set it to PTP (which it is not) we

Greetings to all, I am getting the following error on my PRI-connected Asterisk box, and am just wondering if anyone else has seen this, and if so how they solved it. Jan 18 10:10:23 NOTICE[6070]: chan_zap.c:7428 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 Jan 18 10:10:24 NOTICE[6070]: chan_zap.c:7428 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary

Hi all, I have 1 Card Digium TE412P and 2PRI E1. I have more problems with drops lines. The asterisk log is this: May 16 10:52:26 NOTICE[4465]: chan_zap.c:8194 pri_dchannel: PRI got event: Alarm (4) on Primary D-channel of span 1 May 16 10:52:26 WARNING[4465]: chan_zap.c:2287 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! May 16 10:52:26 NOTICE[4465]:

I am getting: NOTICE[180235]: chan_zap.c:7358 pri_dchannel: PRI got event: 6 on Primary D-channel of span 1 on my asterisk box and it seems to be causing a poping sound in the phones, I am wondering if anyone can shed some light on this. I have scanned the archives and get possibilities ranging form motherboards, to pri, to loaded module problems. Can someone tell me the best way to start

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

I'm running an E400P. Every now and then Asterisk stops receiving incoming calls. This turns up in the messages log: Nov 25 10:49:12 WARNING[65541]: File chan_zap.c, Line 5793 (pri_dchannel): Ring requested on channel 1 already in use on span 1. Hanging up owner. Nov 25 10:49:15 WARNING[81926]: File chan_zap.c, Line 5793 (pri_dchannel): Ring requested on channel 1 already in use on

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Since connecting a PRI to a Digium T100P, I have been seeing the following messages in syslog every few minutes: Jun 4 06:51:54 pbx asterisk[13435]: WARNING[1209214400]: chan_zap.c:6176 in zt_pri_error: PRI: Read on 56 failed: Unknown error 500 Jun 4 06:51:54 pbx asterisk[13435]: NOTICE[1209214400]: chan_zap.c:6913 in pri_dchannel: PRI got event: 8 on span 1 Sometimes, these messages come out

Just upgraded to most recent CVS and now I get this: pri_dchannel: PRI Error: We think we're the CPE, but they think they're the CPE too. when starting asterisk. Needless to say, I can't run asterisk without my PRI. Guess I'll start reverting code backwards day by day until I find the code that works. -Matthew

Just throwing out this question. integrating with Altiware server. PRI appears to be okay. It keeps trying to move my call to a different channel...usually channel 1. This is the deal here: Moving call from channel 23 to channel 1 Then the following errors after no audio then hanging up manually: Mar 24 17:46:17 WARNING[1315]: chan_zap.c:7792 pri_fixup_principle: Call specified, but not

I am trying to connect two machines to each other with an T1 crossover cable. The first machine has two TE120P cards - one connecting to the telco on an ISDN PRI. The second to a crossover T1 cable to a second machine which has one TE120P card. Telco <-cA-> Machine1 <-cB-> Machine2 Machine1: Two TE120P cards Machine2: One TE120P card cA: Standard T1 Cable cB: Crossover T1

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==