similar to: MWI on Zap analog phone not lighting

After purchasing the Uniden TRU9480 and then the Panansonic 5672, both of which do not have "phone company" compatible FSK/stutter MWI, I finally got smart and found out just which Panasonic phones have this feature. Only the following 5.8G models in their current line have FXO compatible MWI. I purchased the 5771 unit and one remote. I have confimed it does in fact work with Asterisk

Hi, Using 1.4.26.1 & DAHDI 2.2.0.2, FSK VMWI devices off a TDM840 work fine. With 1.6.1.[45] & same DAHDI, instead of the FSK spill I get a line polarity reversal. Stutter dialtone is generated as expected. Has anyone else seen this? Is there anything special I need to do for 1.6.1 to make FSK MWI work? Thanks, --Barry

Does anyone have personal experience with a 5.8gig wireless phone (system) that has an MWI that WORKS with asterisk via fxs (in my case spa3k) generated MWI. I know the spa3k does stuttered dialtone but not sure if it generates FSK MWI. I see some that state they do but I also see reviews that say they don't. Doug

Using a TE410P with Zhone 24FXS channel banks to power standard analog phones I can't seem to find out if it's possible to support FSK or voltage type message waiting lamps. I don't want to use stutter dial tone because of the dramatic difference in per phone cost. TIA

Hi.. I am about to replace my aging Nortel Venture system with an Asterisk system and 6 Polycom IP 501 phones, and a couple sipura 841's for less used areas. We have 3 phone lines here. One is SBC, one Vonage, and one Voipjet... One hangup is that I can't figure out how to pass through a voicemail waiting indication from SBC. This is important because my wife and her family all

The TDM410P doesn't support 'hvac', only the obsolete TDM400P supports that option was for the old phones that have a neon light (or equivalent LED+ZENER ciruit). Are other phones off the TDM410P (other than the VTECH) working, or is the Vtech the only model with VMWI available to you. I'm not able to check at the moment, I have copied the asterisk-users list, someone else may

I've upgraded to asterisk-1.6.0-beta2. I'm trying to get the new Telco MWI detection function working. It doesn't appear to be working. I have this in zapata.conf ; PSTN connected here ;immediate=no ;busydetect=yes ;busycount=8 ;musiconhold=default mwimonitor=yes ;mwilevel=512 mwimonitornotify=/usr/local/sbin/zapnotify.sh faxdetect=incoming signalling=fxs_ks context=incoming

Hello, The company I work for recently purchased 2 Rhino CB24s and a Rhino PCI-E R4T1. The channel banks are plugged into the R4T1, as well as 2 PRIs from our telco. The CB24s are for all internal analog phones. Most of the phones are setup in "batphone mode", which is "immediate=on" in the DAHDI config. They are set up this way because we are an outgoing call

pstn incoming on a TDM400P, sometimes i* won't answer, going into a loop like this: -- Starting simple switch on 'DAHDI/4-1' [Jan 16 10:38:55] NOTICE[5808]: chan_dahdi.c:7130 ss_thread: Got event 18 (Ring Begin)... [Jan 16 10:38:57] NOTICE[5808]: chan_dahdi.c:7130 ss_thread: Got event 2 (Ring/Answered)... [Jan 16 10:38:57] NOTICE[5808]: chan_dahdi.c:7299 ss_thread: MWI: Channel 4

I'm trying to get the Telco MWI recognition working in asterisk-1.6-beta7. I'm told that it's supposed to work provided my telco support FSK MWI signalling. I have Verzon FIOS. I believe I have FSK MWI signaling as I can hear the standard stutter tone when I pick up a live handset in front of my asterisk connection. I have the Verizon line attached to a TDM400 card, port 4. I

Hello, it is possible to get MWI working with Grandstream and Asterisk? Thanks. -David

Can someone else confirm that your phone does not recieve MWIs when using SIP and RealTime? Is this a problem with SIP or with Voicemail? -Matthew

Aloha, I'm finishing up the final touches on this install, and have run into an odd problem. I can't seem to get Caller ID on the analog phone lines working. It's a Digium AEX 410 card. I have Verbose set and a line to print the CID: I have usecallerid=yes and callerid=asreceived set in both chan_dahdi.conf and users.conf [analog] include=>default exten =>

Long story short... Snom's ... Retrieve button... works when MWI is *NOT* lit but does *NOT* work when it is lit. Any advice Useragent : snom360/6.5.2 Function: F_RETRIEVE [root@pbx ~]# asterisk -rx "show version" Asterisk 1.2.13 built by root @ pbx on a i686 running Linux on 2006-11-17 16:35:22 UTC [gateway] exten => 201,hint,SIP/201 exten =>

Folks, I've tried to find a reference, but I've had no luck, and would appreciate your thoughts: I'd like to be able to monitor a telco line for Message Waiting Notification, however I cannot figure out if this capability is available. Detecting either FSK or Stuttered Dial tone would serve, but I can't find anything in the list archives or Wiki with clues as to how this might

Hello. I am using a snom 320 running 5.3.6 with Asterisk 1.2.4. In the sip.conf entry, I have mailbox=1234@default and vmexten=*98. The light on the snom 320 turns on when I have voicemail and the retrieve button dials the correct extensions. However, the light turns off immediately after making the call to voicemail, even if I do not check the voicemail. Any idea on how to get this to behave

Hi all, I'm having sudden MWI problems. Everything else on the phone works fine though. I have three Cisco 7940s. Asterisk server is behind a firewall running NAT. (192.168.1.202/24) Phone #1 - On the same subnet 192.168.1.250. Everything works great. Phone #2 - On a different subnet, 192.168.2.0/24. Everything works fine except the MWI. It never comes on. This is over an IPSEC VPN, but

Hello, All :) Regarding to incoming caller ID on PSTN line, which one is best supported by asterisk: is it FSK ETSI or FSK US? I bought some caller ID converter hardware (convert DTMF to FSK and vice versa) but still asterisk can not detect it. The converter has a switch FSK ETSI or FSK US This is what I put in /etc/asterisk/chan_dahdi.conf ... cidsignalling=bell cidstart=ring ... If after

We have several agents on queues, and want to indicate to them that they are logged in or logged out. We have tried several different ways, from changing the screen to presenting different service menus, but cannot get anything to be "in their face" (their words, not mine). One of our team has suggested, as the agents do not have voicemail, is to use the MWI on the 7940 phones to

I have a Samba-LDAP PDC at an office and 5 BDC's at other offices. At corporate HQ I have a W2k Server and domain. I have properly configured an interdomain trust and Users in the Samba domain can get to sections on the W2k machine regardless of location. However, members in the W2K domain can only access shares on the PDC. Attempts to access shares on a BDC cause a user name