similar to: SER vs Asterisk for SIP

Does anyone know if the E1 cards that digium sells work in India. Also are there any distributers for those cards in India. By E1 cards I mean E100P, TE410P or TE405P -- regards Vikram (http://www.vicramresearch.com)

I am planning to go in for a E1 line and whould like to know what questions i need to ask my service provider so i can connect that E1 to my asterisk box using the digium E1 card. what I mean is will my service provider give me info like LBO, framing , coding etc which i need to configure the span tag in the zaptel.conf and what about B and D channels am I allowed to setup whichever channel I

I have 20+ asterisk servers and need to network them together so a phone on any of the servers can call a phone on any other server without any trouble. I can think of IAX trunks between every server. So every server will have an IAX trunk to every server and then prefix bases routing in the dialplan for each server (I can give a number to each server and use that as a prefix for that server).

I configured agi-test.agi on extension 111 when i dial into asterisk extension 111 using a IAX softphone and hangup while the AGI is playing asterisk crashes. Does anyone have any idea why this happens. -- regards Vikram (http://www.vicramresearch.com)

In a pure voip envoirnment which uses a single codec say ulaw across all its phones can asterisk support 5000 voip sip phones on a dual / single xeon with 1 gb ram. If all the phones support reinvite (Send RTP stream directly to each other). Or would I need more than 1 system to support 5000 phones in the enviornment described above. also I am not talking about the phones using meetme or

Does anyone have any experience ith configureing the sangoma A102 card for testing using a e1 cross cable i've configured and installed the cards properly even the lights on the card are green which proves that my cross cable is properly built too. my problem is with asterisk which gives me these errors PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got event: HDLC Bad FCS

Hello: I have successfully install spandsp and patch asterisk with it. But when I received a Fax is garble or shrink. Does any one know why???... Am using a PRI T100P card to receive the fax and save it to a tiff file... Any help will be greatly appreciated. Here are the versions. Latest csv from asterisk, spandsp-0.0.1k.tar.gz redhat 7.3 T100P has its own IRQ. Any help will be greatly

After days of searching i've finally figured out that E1 lines in india use multiple types of signalling from EuroISDN to R2. Digium E1 cards dont work for R2 type signalling. Can anyone suggest me asterisk compatible E1 cards which would work on R2. Also if anyone on this list is from INDIA and uses asterisk and E1 lines please let me know what type of cards (which vendor) do you use and what

I just came across libr2 anyone using it in its current state. Specifically someone from India or around India using it. Also does it work with the digium e1 cards or only the Dialogic cards. http://digium-cvs.netmonks.ca/viewcvs.cgi/libr2/ -- regards Vikram (http://www.vicramresearch.com)

Any more ideas on my below mail? If a user is registered with SER and leaves a voicemail message with asterisk (by using rewritehostport etc in ser.cfg), then how is the user supposed to listen to the message afterwards? Is there any other way other than the MWI method?? Thnaksm Aisling. ---- Original Message ---- From: ashling.odriscoll@cit.ie To: asterisk-users@lists.digium.com Subject: FW:

Hi all, I have SER and Asterisk set up together with ser handling user registrations and asterisk providing voicemail services. When I ring a phone and it doesnt answer after a designated amount of time, the request is forwarded to asterisk, and I can leave a message. Now, this may seem a ridiculous question but how can I listen to my message afterwards? I have read about a solution by Java

Hi All, I have a thin cliente here that i want to run asterisk: - National Semicondudor Geode GX1 266MHz Geode 266MHz single chip - NS Cx5530a Southbridge National Semiconductors SC2200 - NS PC97317 in chipset - 32MB Compact Flash - 64MB Ram - 10/100Mbps, Autosense 10/100Mbps, Autosense Realtek 8139C National DP83815 / DP83816 Some tip? I have a ide>flash

Hi all, Hope somebody can help-I really am stumped as to why this won't work. I realise that this isnt an Asterisk problem (Please dont bash me on the list) and I have emailed the SER list but I havent received a reply and maybe someone on this list can help...Once this problem is solved I am going to use Asterisk for voicemail etc with SER (I have it set up) I currently have SER set up and

Kevin wrote: > There is a reboot script posted on the wiki to reboot Polycom > telephones. When I execute this script, I get the following messages. > I am concerned as this is causing issues with asterisk and the PRI. > Does anyone have any ideas why this would be happening? > > > > asterisk console: > > -- Remote UNIX connection > -- Remote UNIX

Hi, Thanks for your response on the kernel switching.I was away and could not reply immediately. Right now, I am facing a differentissue. I have to set up DNS server using BIND on Centos 4.3. When Itype the hostname on Centos, it shows: sipserver.vodcalocal.com But the cli prompt has root at sipserver~ meaning only the sipserver part of the hostname is displayed. whyis this so? What is the

Hey gang, I'm trying to work out all possible scenarios using SER & Asterisk in our upcomming deployment. The example scenario is 50 different customers, all with different numbers of SIP UAs. All UAs would register with SER; This will help keep any inter-office conversations off our bandwidth since SER doesn't handle the RTP stream. Calls from PSTN to UA are easy to handle.

Dear All, I have the following setup. Quad T1's<->Asterisk (PBX)<->(LAN<->DMZ)<->SER<->(Firewall)<->(Internet) | Local US Help Desk (Snom 200') This setup works well. I can pass calls from over the internet to the Asterisk PBX via SER using X-Ten Lit. I have a couple of questions; 1. How do I

Hi all, I would like to know if it is possible to use asterisk and ser together in a single computer system using ser as a sip proxy and forwarding any voice call request to asterisk for calling into the pstn gateway. (or any other alternative that is possible is also welcomed for suggestions). If it is possible can someone kindly show me the necessary configuration files or refer me to any page

Anybody out there use Ser along with *? Any advantages disadvantages? Is this even a good idea?

Hi, I'm trying to transfer an incoming call from the PSTN to another PSTN number through a SER - Asterisk system. SER doing only routing.. pstn call-> SER -> asterisk (call forward) -> SER -> pstn Logic for SER: If something comes from the pstn, send it to asterisk. If something comes from asterisk, send it to the pstn. Every time I am getting a "Got SIP response 481