similar to: TE110P error

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

I have one TDM2404E digium card on asterisk box, after configuring the zaptel and zapata configuration files, I am getting these errors when reloading asterisk: ast_unregister_indication_country: Removed default indication country 'us' setup_zap: Ignoring signalling setup_zap: Ignoring answeronpolarityswitch unable to recognize channel 13-5 what is the reason for that? Thanks,

Hi, I've just got a TE110P card and installed at Asterisk. I configured zapata.conf, according to www.digium.com/index.php?menu=configuration, but the following error is happening: ... ... ... [chan_phone.so] => (Linux Telephony API Support) == Parsing '/etc/asterisk/phone.conf': Found == Registered channel type 'Phone' (Standard Linux Telephony API Driver)

Good day all I downloaded bristuff RFC3 and asterisk,zaptel,libpri versions 1.0.3 This is to install my quad bri card All installed well I coped over some old config files.All 4 ports are available,so that gives 8 open lines for incoming or outgoing,correct me of I'm rond The problem is,asterisk can only handle 2 calls at a time if there is 1 incoming(into pstn) and there someone already made

When I reload the asterisk I get the following warnings: Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring switchtype Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring signalling Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring rxwink Everything works fine as far as I know, I can dial and complete calls. So why am I getting this

Hi Since Im using the mISDN drivers and no zaptel stuff, I had to install ztdummy to get MeetMe to work. Well, that was the plan. Now, after getting the latest zaptel version over CVS (Im using Kernel 2.6), uncommenting all the modules except ztdummy in zaptel.sysconfig file and compiling this by "make", "make install" and "make linux26", I rebooted and

Good day all What is the amount of calls that asterisk can handle,SIP and from/to PSTN -- Thanks Altus Snyman Stormcorp Network Solutions +27 11 8071141 exten 301

Good day all I got my Music on hold to work but can I/how do i get music on transfer? Please help Thanks

When I reload the config, I see this error in the CLI. However, I don't see what I have done wrong: == Parsing '/etc/asterisk/zapata.conf': Found May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured channel 1, FXO Kewlstart signalling May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured

Hi list, I have bought some Cisco 7941G-GE IP phones and want to use them with asterisk. Before bying I tested the whole setup with three different models of the old 79X0 series (a 7912, 7940 and a 7960). Flashing the formerly provided SCCP-Image to SIP was no problem, but now it complains about a nonexistent CTLSEP<mac>.tlv file. Most of the howtos say something about an empty file but

Good day all I'm just wondering for interest sake I have a box,hostname=myname.co.za,running sendmail If I send mail to someuser@myname.co.za it try to deliver to the box,witch does not have the mail box.How do I tell sendmail that it should send mail to myname.co.za's mailserver. I know how easy it is to change the name but there's a lot of reasons why we can.It is not in the

Good day all I added the music on hold entry in vpb.conf and commented out default line in musiconhold.conf. Asterisk starts up with the default mp3 but as soon as I remove it and add my mp3 it just doenst start up and gives a broken pipe error? Please Help or advice Thanks ALtus

I reloaded my asterisk and found some red lines flushing by. When I stopped it I see: WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring signalling WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echocancelwhenbridge WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echotraining Reconfigure channel 1, FXO Kewlstart signalling Reconfigure channel 2, FXO Kewlstart signalling

Good day all I got my snom 220 phone so that it displays on the buttons if someone is calling that extension I just added "exten => 403,hint,SIP/403" in my dialplan But These lights only comes on if someone calls that extension,not if that extension is busy are a call is made from that extension Can this be done? Please Help Altus

Good day all IS there a way to personalise the voicemail message when you leave a message? Thanks Altus

Hiya all, I have had no end of trouble trying to get my A101 E1 card working on a new asterisk installation. The sangoma tech people have ignored my emails about this. All the installation of wanpipe seems to go ok, and zaptel. it all installed compiled and does all the wanpipe hwprobe exactly as documented. Asterisk compiled ok, but when I run it give me Jun 27 11:12:18 ERROR[10528]:

Good day all I got my voicemail message working,thanks but now,keep in mind I'm using SIP We have,for example 4 people in our admin department.Each user has its own voicemail so that when their extension is dialed directly and not answered it gos to voicemail. But there is also a option to dial 3 for admin with will dial all 4 number in sequence.This I got working 100% but now I want a

Good day all Is it possable to set asterisk up as a cdr server for other voip units We got a quintum dx here and its got a option to log to a cdr server on port 9002 Thanks Altus

Good day all We have a quad bri card,installed on fedora core1,downloaded the latest bri-stuff that download asterisk 1.0.3 and zaptel 1.0.3 and libpri 1.0.3 All installed and working.BUT after 5min+ of talking it just drops the calls? Any reason why? Please help Thanks Altus

Hi all, I have a problem with the cvs head zaptel library: I cannot update my zapata.conf into asterisk when I issue the reload command from the CLI prompt; only when I stop and restart the asterisk service. The system sends the following message: Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364 setup_zap: Ignoring switchtype Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364