similar to: TDM04b failures (xpost on purpose)

Hello I have installed a TDM04B and disabled any devices not required in my PC. (TDM04B is analog card with 4 ports to plug into telephone co lines). I am running this version of * Asterisk CVS-HEAD-01/10/05-02:11:15-AstLinux built by root@ls on a i686 running Linux As you see below the wctdm module is loaded: pbx root # lsmod Module Size Used by binfmt_misc 12296 1 - Live

I noticed the following came into cvs head yesterday: > Update of /usr/cvsroot/zaptel > In directory mongoose.digium.com:/tmp/cvs-serv2118 > > Modified Files: > fxotune.c wctdm.c wctdm.h > Log Message: > More TDM card echo API modifications. Making the fxotune program automatically > find the correct coefficients for the module. Lots of neat stuff. I did a complete

Hi, We have a PRI Trunk (physical E1) and we are getting some rather weird and very isolocated problems. On outbound calls to specific numbers, it would seem to me that DTMF from the remote side is affecting the local asterisk system. Basically what happens: - We make a OUTBOUND call via the PSTN (PRI Trunk) to a remote System - Remote Answers, and converse - Remote sends DTMF on their site to

In the next week or so, we'll be turning up a new T1 Pri from Cox Cable in Omaha using a T100P (installed but not yet configured). While discussing the interface parameters with a very knowledgable Cox engineer, we decided on some of the basics including b8zs, esf, dchan=24, callerid, 5 digits of called number forwarded to *, and switchtype=national (NI2). They indicated their CO switch is a

Hi All This may be a silly question but... I have this dahdi_genconf generated file: ; Autogenerated by /usr/sbin/dahdi_genconf on Fri Jul 4 22:05:29 2014 ; If you edit this file and execute /usr/sbin/dahdi_genconf again, ; your manual changes will be LOST. ; Dahdi Channels Configurations (chan_dahdi.conf) ; ; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended ; to

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

Hi all, I have a problem with the cvs head zaptel library: I cannot update my zapata.conf into asterisk when I issue the reload command from the CLI prompt; only when I stop and restart the asterisk service. The system sends the following message: Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364 setup_zap: Ignoring switchtype Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364

Hi i have a tdm2400p and installed asterisk 1.4.11 with zaptel 1.4.5 im having an error message when in running asterisk with the tdm card in. here's the error from the console of asterisk: [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:7489 mkintf: Unable to get span status: Inappropriate ioctl for device [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:10466 build_channels: Unable to register channel

Hello I am struggling to get my TDM04B working. Just to rule out a hardware problem how can I check that the hardware works? How can I then check that the drivers are loaded correctly? Angus -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050620/470458c6/attachment.htm

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

Can't get a Digium TDM04B working. Asterisk is running. I seem to have setup the trunks OK. But whenever I make an outgoing call get the 'all circuits are busy now' message. If I call in nothing happens at all! Here is my zapata.conf file: ; ; Zapata telephony interface ; ; Configuration file [trunkgroups] [channels] language=en context=from-pstn signalling=fxs_ks fxsks=1-4

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

Hello everyone, I have a Atcom AX-1600P(1) card with a FXO module and I can't configure it. I have four extension with this PJSIP settings: --- /etc/asterisk/pjsip.conf --- [transport-udp] type=transport protocol=udp bind=0.0.0.0 [6001] type=endpoint transport=transport-udp context=from-internal disallow=all allow=ulaw auth=6001 aors=6001 direct_media=no rtp_symmetric=yes force_rport=yes

Hi, My asterisk server was working with a 4-FXO analog card (TDM400P). I recently added two digital cards: a TE120P (1 PRI) and a B410P (4 BRI). The B410P is still unconfigured but inserted in a PCI slot. The TE120P's jumper is set to E1 as it will connect to a commercial PBX's PRI card also configured as E1. My analog channels used to be 1-4 but since I added the new cards I changed

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

Looking for some help from the UK please. I backed up all my Asterisk configuration before re-installing the server from 32 -> 64 bit. Unfortunately I did not transfer the backup to another machine!!!!! I now have a TDM400P that is not picking up the line. Can you see what I have done wrong when I have rebuilt the config please: dahdi_scan ---------- [1] active=yes alarms=OK

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

I'm having a problem receiving incoming faxes and I'm hoping someone here can help me out. My system is a PBX in a Flash with one dahdi card for my incoming analog lines and another dahdi card for my analog devices (fax and modem). My dahdi-channels.conf file looks like: ; Autogenerated by /usr/sbin/dahdi_genconf on Tue Jun 23 14:56:24 2009 ; If you edit this file and execute