similar to: OT: DSL without voice

Hi, Does anyone know of a way to get a dry copper pair (also known as an alarm line) from Verizon for less than $20/end? I know we have been able to get them, but they come out to $40/month for a circuit.. and there's no dial-tone over it!!!! -------------- next part -------------- An HTML attachment was scrubbed... URL:

Sorry for the long descritpion of the problem, I''d like to know If I misunderstand something or if I meet an intrinsic limit of my setup. 217.58.51.162 HDSL eth1 - SRV_XP: 192.168.254.10 eth0: 192.168.254.1 -----+------------------+------- 81.121.243.250 ADSL eth3 - I want to allow incoming pptp request (port 1723) to be forwarded to srv_xp

Hi I've bought the Wildcard TE110 some days ago but I'm unable to get it to work with Siemens HiCom 300. I've tried this so far: 1. I've used standard cat5 cable cut off on one edge and twisted wires 1 to 4 and 2 to 3 which is according to cisco a short circuit for E1 lines. Wildcard takes a few seconds and sets the link to green (OK). 2. I've tried to connect our running

I'm looking to expand my bandwidth for my Asterisk PBX. Why should I choose a T1 over DSL for my asterisk server? I found someone offering T1's for $290 a month + Loops or 3 Meg for $561 a month + Loops. Is this a good deal? Thanks Bart -------------- next part -------------- An HTML attachment was scrubbed... URL:

Do the Digium cards have a built in CSU? Is a CSU an FCC requirement? or just a carrier requirement? TIA

I apoligize in advance for this newbie question on what I perceive as a mostly advanced level list... I did some searching, but would like some of your expert opinions. I'm building an asterisk server to be used in the home, both to learn, and as proof of concept of applying this solution in a home. To keep costs down, I'm considering one X100P ($25 ebay clone) card to connect the

So in order to answer the background and backbone questions here is the system as it is. I hope this isn't too much for the list but I'll post it in response to a few inquiries. The current system is quite interesting. We have an office in a town that is about 50 miles from the ski area. The ski area is powered 100% of of generators and the telephone access and internet access goes from

OK. Now I show my ignorance. What's the difference between a T-1 and a channelised T-1? I see that Covad's voip service (formerly GoBeam) requires a channelised T-1. Then I read recently on the list that many T-1s being installed are actually HDSL....which would be not a T-1 at all...right? Michael -- Michael Graves mgraves@pixelpower.com Sr. Product Specialist

Hi! I'm trying to setup a Wildcard TE110P with a PRI in The Netherlands. I get a Red Alarm on the line. Is there any way of debugging this? I've tried some configs that should work but without success. Is there any way of telling if the cabling is correct or what else the problem could be? Thanks!! Remco

I'm not receiving ANI2 (info digits) on my SBC PRI's. SBC said they're sending them. I called Digium support and was told it is not supported. Is anybody receiving ANI2 on a PRI? Thanks in advance, ------------------------------------------------------------------------ Steve Edwards sedwards@sedwards.com Voice: +1-760-468-3867 PST Newline pagesteve@sedwards.com

Hello! There is something I really don't get: As I ordered a PRI ISDN line in Germany with DID, I had not to pay anything for a "DID number block", now I'm trying to get a PRI ISDN in the U.S. (CA) and SBC wants to charge more than 200 USD/month for numbers. I mean, this has nothing to do with DID, where everything that comes after the "base number" will be

I have what my SBC/ATT representative calls a "Supertrunk," but he can't tell me the specifics I need to know to configure Asterisk to work with it. By fiddling about, I've come up with the "almost working" configuration below. This works except that it takes about 4 seconds from when the console says the line is answered until it plays my prompt. Watching the

I have some weird error with one of my samba installation. When modifying samba password using smbpasswd, samba seems trying to add same attribute (instead of delete and add again), pls see the "MOD" from log file (from different domain) : UNSUCESSFULL Mar 15 17:10:53 hurricane slapd[27056]: conn=29489 op=1 MOD dn="uid=pwreka,ou=people,ou=purwakarta,dc=indorama,dc=com" Mar 15

hello, I have a test setup with 2 asterisk servers, each having a one snom 100 via sip using it. I`m experimenting on how trunking between them would work. I have them setup for RSA authentication which I plan to use in the future. So I`ve setup the keys and servers seem authenticate to each other. One is named phila and other hurricane. Here is what I see on phila: -- Registered

I have to provision several dozen * users to a seperate building on our campus in the same subnet. Ordinarily, I'd just run a gigabit cat6 cable to another switch if it doesn't violate the 100 metre rule, but this building is several hundred metres away from my backbone. My only option for cabling to the remote building is copper. My plan is to provision them with a Linux bridge with 4

Hi I would want to use the patch for squid released by patrick mcHardy, but it requires that squid is located on the same machine that does traffic shaping. My configuration is different: i have the screening HDSL router directly connected to a multi-ethernet firewall and the proxy located on a DMZ box. i would want the firewall doing traffic shaping. Internet |

I have Sipura 841's talking to a CVS-HEAD of August 4. If I disconnect the power to the Sipura, Asterisk does not hang up the channel. My sip.conf for this phone looks like: ; [super1] ; Sipura 841 disallow = all allow = ulaw callerid = "super1"

Hi all, I'm currently getting my Centos working as a proxy (squid) on a 2 Mb bandwidth plan that's serving 20 users. it's all good though our need for speed is increasing by the day. soon enough i'll be serving up to 60 user, hence the need to get higher bandwidth though here where the problem is. as i'm using HDSL, 2 Mb is the highest plan available. hence, i need

Hello, I am working with a database system from which I can retrieve these kinds of user defined fields formed as XML ... <udf:field unit="uM" type="Numeric" name="facs.Stain final concentration">5</udf:field> You can see in the above example that "field" is defined in the namespace "udf", but that the "udf" namespace is

Hi all, I have a problem with a new Shorewall box I''m trying to migrate from iptables rules to shorewall 2.2.0. I have a 3 interfaces setup: - eth0 ---> internet (ip address) - eth1 ---> remote office (10.0.0.0/8) - eth2 ---> lan (192.168.16.0/24) I''m using a very simple and common setup, with just a few DNAT rules in my /etc/shorewall/rules file, and about twenty