similar to: Two zaptel T1 cards: no clock from one

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Hi all, I've got a TE410p connected via T1 to four channel banks (2 FXO and 2 FXS), no PRIs. Some users are complaining that they hear clicks and pops on the FXS lines, generally when they pick up the phone it's noisy. This happens only after a while, e.g. after a fresh restart of everything, all is fine but after some time these noises start appearing. From what I've read on the

I am having some difficulty getting a T100P card to work with my PRI. When I attempt to make an outbound call via: exten => 1004,1,Dial(Zap/g1/NPANXXXXXX) I see the following on the asterisk console: -- Executing Dial("SIP/sbruton-b8ce", "Zap/g1/NPANXXXXXX") in new stack Apr 21 08:18:48 NOTICE[16401]: app_dial.c:554 dial_exec: Unable to create channel of type

Hello All, I have a Digium Wildcard TE410P Quad-Span T1 Card, when I do connect T1 lines it goes in RED. When I do connect the same line on a different Server (Same Model T1 Card) it works fine. How do I examine/diagnose my T1 Card for any hardware failures. I heard about loopback test , how helpful it is? Here are my configuration /etc/zaptel.conf span=1,1,0,esf,b8zs

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

I am having trouble getting my T100P and ADIT 600 talking. I have 2 FXO 8 port cards in the ADIT and a T1 controller card. I have a T1 x-over cable connecting two together. Here are copies of the relevant bits of my zaptel.conf and Zapata.conf Zaptel.conf span=1,0,0,esf,b8zs loadzone=us defaultzone=us Zapata.cfg context=default signalling=fxs_ks group=1 channel => 1-24 My

I'm trying to get a Carrier Access Corp. Channel Bank I working with a Digium T100P without success. What is stranger is that the status lights on the channel bank and T100P seem to change almost each time I power cycle the channel bank or reset the T100P. The channel bank has three status lights: T1, Framing, Status. T1 is green, Status is yellow, and Framing is usually red but sometime

Does anyone know how to monitor * to see if they are receiving timing slips on a span connected to a T100P card? I am seeing b-channel restarts quite often and also getting "No D-channels available" warnings from time to time. Yesterday I had all the b-channels crash during a MeetMe Conference. Not good! This PRI is connected to an Avaya Definity PBX that is onsite and located in the

I run a SIP-only shop with a 23 channel PRI and single T100P. Here are my configs: /etc/zaptel.conf: span=1,0,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone=us /etc/asterisk/zapata.conf [channels] context=default switchtype=dms100 signalling=pri_cpe pridialplan=unknown rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=no hidecallerid=no callwaiting=no

Hi - We're moving up in the world to a PRI (Verizon), and I'm having some problems with it. I'm new to this PRI thing, though, so maybe I've just screwed up a simple config detail. I've got a TE410P on a Dell PE1600SC (ServerWorks Chipset). The card itself has a green light for the PRI, and Zttool shows Span1 as "OK". All I'm getting when I call into any

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

Hi, I am about to pull my hair out after trying to get our PRI up and working. We are switching from a Cisco gateway to an Asterisk box which provides the 23 phone lines for our office. So, because the Cisco gateway is working I can assume I have all the settings right (b8zs, esf, dms100, etc) and the PRI is live (because we are switching over). When dialing from PSTN, I get busy signal. When

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

Hello everyone, I'm using a TE410P, no irq sharing, and all extraneous devices disabled, such as USB, Parallel etc. I'm getting a few IRQ misses according to ZTTOOL. We're running a standard PRI_CPE interface and seem to be getting dropped calls, and errors on the D-CHANNEL occasionally. The circuit itself is very solid, it was in use on our old PBX just a few weeks ago, never

In the next week or so, we'll be turning up a new T1 Pri from Cox Cable in Omaha using a T100P (installed but not yet configured). While discussing the interface parameters with a very knowledgable Cox engineer, we decided on some of the basics including b8zs, esf, dchan=24, callerid, 5 digits of called number forwarded to *, and switchtype=national (NI2). They indicated their CO switch is a