similar to: E&M Digium card quotation

Can i register a cisco 7902G with asterisk????? what i have to do??? thanks in advance. R -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20041130/12bf3c06/attachment.htm

i was looking but i dont find how do this: configure the password for the extensions read the messages and some other things related with this can some bady help me with some material or a explicit example. thanks in advance Rodney Acosta Coya.

Hi I have a brand new ATA186 with the following firmware: Version: v2.15.ms ata186 (Build 020919a) I have been through the archives about how to configure it, but my colorful configuration web page does not have the same fields that people say I need to adjust. Even the examples on Cisco's web site don;t match. For example, I don't have the GtkOrProxy field, which is an important

I dont have a cisco acount yet can some bady hel me with the ata18x-v2-16-030401a-1.zip file. thanks in advance Rodney Acosta Coya. Dpto. Tecnologia de la Informacion. racosta@moanickel.com.cu Tel:(53)(24) 62 611 -----Mensaje original----- De: Paul Rodan [mailto:asterisk@glitch.cc] Enviado el: Martes, 23 de Noviembre de 2004 11:24 a.m. Para: 'Asterisk Users Mailing List - Non-Commercial

hi all i upgrade a bt100 phone and it can't resgister with asterisk Dec 1 13:25:49 NOTICE[1112980400]: chan_sip.c:7519 handle_request: Registration from '<sip:@172.16.4.249>' failed for '172.16.4.226' is was working with the version 1.0.5.3 some bady now what is hapening? thanks in advance Rodney

Hello, I just wanted to know if any of you has successfully (or know about) installed the Dialogic 4xFXs ISA CARD D/41 ESC? Does it work with *?, if so, how is the driver called? Thanks a lot for your comments. Alejandro Acosta,-

Has anyone found an inexpensive E&M trunk card that will play with *? Looking for an interface to a legacy electromechanical PBX that's able to pass answer supervision. Docs on the X100P card would be helpful, we could probably pull E&M out of that. Any ideas?

I need to create a couple of tie lines between a legacy system and an Asterisk system. I was told that the tie lines are E4 Superframe E&M. I have done E&M wink but have no idea about E4 Superframe E&M and Google is not helping me here. Does anyone know about this type of signaling and if Asterisk can handle it? Thanks, Steve

Hullo over there. i'm trying to link an asterisk box with a legacy PBX system with a four wire trunk line. the legacy PBX has 21 analog phones connected to it and i would like to route calls to another site via the asterisk box. i would like to use E&M signaling over this line. my question is how many simultaneous calls can you have over this line with E&M signaling. is there a better

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

How do I setup my T1 card as an E&M tie line? Any special configuration? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050523/8aac4dbf/attachment.htm

Hi, Can anybody with previous experience with it guide me on how to setup asterisk with analog e&m to connect it to an old style e&m system which uses 4 pair cables on RJ 45 jacks. All the analog cards I know of use RJ 11 jacks. And there is no choice of modernization of the customer equipment. Cable pin out are as follows: 1. M lead 2. E lead 3. Tip1 4. Ring 5. Tip 6. Ring1 7. SG 8.

I am trying to make an in/out trunk group comprised of 4 DS0's using E&M Wink signalling. The first four channels of a DS1 on a T100P are being used for the group. Outbound calls work fine, but inbound calls fail. The other 20 DS0 channels are used for a PRI. Does the configuration shown below look okay? I've tried setting 'immediate => yes' without success, but it

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

Attempting to talk to an Eagle Telephonics switch at a disaster exercise. Didn't think a plain old E&M wink start T1 would be this much of an issue. We finally got the Eagle to accept a call from *, but whilst I can hear the person on the Eagle, they can't hear me. When they initiate a dial out I only get the first 2 digits from their switch... Does anyone have decent

All, One of our customers is using a Telrad PBX, we are providing phone server through asterisk via a T1 using e&m directly connected to the Telrad system. We're using a T1 cross cable as normal, the T1 part works great. No alarms. When we try and dial out the Telrad using a direct trunk group, the call fails. When looking in the asterisk console I noticed only 1 or 2 digits are seen,

Hi all, In this moment I have the opportunity to install asterisk in Poweredge 1400 Dell Server (PIII, 2 GB of RAM). I wonder if any of you have any experience running asterisk (+ Digium cards) on this kind of hardware, any comment about know problems or good experiences are welcome. Thanks in advance. Alejandro Acosta,-

I am setting up a box with a T100P. Everything is going well. The company I am working with has their one phone switch gear. They provisioned me a E&M Wink T1. Cannot do PRI unfortunately. We chose E&M so we could pass an unlimited number of DIDs to the trunk as apposed to FXS loopstart signaling. I can make outbound calls no problem, but I am having problems with the dial plan for inbound

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

I am an Asterisk newby, and I cannot seem to get Caller ID information from our T1 line. When calls appear at the phones, they say the call came from "asterisk" and unknown number. I know how Caller ID information is passed on an analog phone line (between the rings) but with a T1 line, I don't know technically how it is done. I don't see the caller's number in the