similar to: P2P (DDI) mode with chan_capi 0.3.5

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hi, I'm trying to get a fritz working in our asterisk box, however I'm getting the following error and was wondering if anyone could be of any help: -- Executing Macro("SIP/2002-5501", "enum-call|call|0405152568") in new stack -- Executing Goto("SIP/2002-5501", "call|0405152568|1") in new stack -- Goto (call,0405152568,1) ==

Hi; I've been asked to take a (remote) look at an Asterisk@home system running asterisk 1.0.9 on Centos 3.5. It's running chan_capi-0.3.5 It has an AVM c2 ISDN card which is plugged into what I believe to be a couple of BT ISDN2e "System Access" (i.e. point to point) connections. We've placed a support call to BT to find out how these lines are actually provisioned, but

hi when two calls are active on controller 2, chan_capi won't use controller 1. this is with AVM C2 roy -- Executing Goto("SIP/torgeir-b476", "capiring|BYEXTENSION|1") in new stack -- Goto (capiring,90044875,1) -- Executing Dial("SIP/torgeir-b476", "CAPI/22545066:bBYEXTENSION|120|Ttr") in new stack == data = 22545066:b90044875 ==

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 i fixed wrong capi.conf (there was [controller1] after [interfaces]) now capi.conf is: ; ; CAPI config ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] msn=855285,859609 incomingmsn=* controller=1,2,3,4 softdtmf=0 accountcode= context=local ;echosquelch=1 ;echocancel=yes ;echotail=64 ;callgroup=1

Hi, I?ve strange problem when I?m making a call from SIP (Cisco 7960) to capi (Fritz PCI). When I call a national number, I?m hearing the ringtone when the called party is ringing but when I call an international number, I don?t hear the ringtone and I?ve a silence until the called party answers. Both call are going through the same extension. Here?s 2 log files, one with a national number and

Hello, Actualy I have got a PBX conected to a BRI port on a Cisco Router witch route the calls. The router is using h323 with the other end. How could I replace the actual PBX and pass all the calls to the router, as now works. I tryed connecting an asterisk CAPI port against the same BRI Cisco port, but I can not make any calls, I get the following error from asterisk. Connected to

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

Hi, Regarding capi debug, I don't know how to translate reasons like 0x3302 or infos like 0. I didn't find any 'translator' googleing capi debugging. Do you know about any 'translator' for this or should I be as clever as to know what a reason 0x3302 is? What is this debug for if I can't interpret it? Kind regards, Victor. >From capi debug: == CAPI Call

Hi all, i have asterisk 1.0.9 with an Eicon Diva 4bri and chan_capi-cm-0.6. I have 2 NTBAs (one with did and one without). When using the one without did, i am able to place outgoing and incoming calls. When i use the NTBAs with did i have a layer 2 error. Anyone an idea? -- Executing Dial("SIP/2004-9634", "CAPI/g1/43XXXXXX") in new stack > data = g1/43XXXXXX

Hi, I have an AVM Fritz! ISDN card connected to an NT1 unit (Australian). I have no problems getting the drivers up and running but when using it with asterisk nothing happens. I call in using a mobile or analogue phone on either of the numbers and the NT1 activity light either flashes or goes solid while ringing but it pauses for a while and on a mobile i get call not answered and a busy

Hi all, does anyone have capiECT working? I can't get it to work - please see my logfiles below. While using an * CVS version of late September and chan_capi-0.2.5 (I guess), it worked!!! (I know, never change a running system ... should've backuped ... etc.) Here's the setup: NT----AgfeoISDNPBX----AgfeoISDNPBX----AnalogPhones in between the two PBX I attached my * server with a

Hello List, I'm trying to get a PrimuX Card (www.primuxisdn.de) working. The Manufacturer says that chan_capi (the older one) used to work. Now I'm trying with chan_capi-cm and have got the following problems: Outgoing calls "ausgehend_ueber_ntba_primux.txt" the other phone rings but when I answer the call asterisk crashes. Incoming: first tried with immediate=no

Good day, The unusual thing about this problem is that it doesn't occur just during a CAPI call, or just during an IAX/SIP call. Only during IAX/CAPI I'm having some trouble with the CAPI interface and it only occurs when a call comes in on an IAX channel and goes out the CAPI interface. The capi debug in the asterisk console is below as well as the relevent parts of .conf files from

Hello, I need to detect both fax and answer machine, and it should be valuable that the detection will be run by the Diva card itself. So : - I read Diva Documentation, and I found that the Diva could send some specific DTMF, if I had "[..] enabled [this functionnality] by the application for a designated controller through a manufacturer request command 9 [...]", but I didn't

Hello, These are error messages I get when I try to call a number over CAPI channel. -- Executing SetCallerID("SIP/xlite1-3b80", "0") in new stack -- Executing Dial("SIP/xlite1-3b80", "CAPI/hfcpci/b17") in new stack > data = hfcpci/b17 > capi request for interface 'hfcpci' == hfcpci: Call CAPI/hfcpci/b17-1 (pres=0x00,

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

[Something seems to have went wrong with my previous posting. It appears on the archive page in another thread. I did not receive anything myself. So I may give it another try:] Hi, the first thing I did with Asterisk is listening to `demo-congrats' by Xlite on the same machine. This works perfectly. The config files are those shipped with the package. Now I want to listen to it over

Hi, the first thing I did with Asterisk is listening to `demo-congrats' by Xlite on the same machine. This works perfectly. The config files are those shipped with the package. Now I want to listen to it over ISDN/Capi but I don't succeed. My `capi.conf' is like show in many tutorial on the web. In `extensions.conf' I just added the following lines: [capi-in] exten =>