similar to: problems with X100P -Nochanneltyperegisteredfor'Zap'

For reference... http://www.voip-info.org/wiki-Asterisk+zap+channels Not sure it is relevant but go ahead and remove the spacing on the channel line so it will read.... channel=>1 Here is the original incoming context you showed. [incoming] exten => s,1,Answer ; Answer the line exten => s,2,Playback,demo-thanks ;for playing a file The Playback looks malformed based upon the wiki

This may seem obvious or silly but have you tried using a different phone cord? A bad phone cord played havoc on a colleague of mine during initial config. Fro what you show as your output from ztcfg, you should have one channel configured successfully then. Your example shows you have the channel set to one so no problem there. If you run ZAP SHOW CHANNELS from the CLI what do you see? W

Just to make sure this isn't a typo in your original email... Is this example from your zapata.conf? Also, the extension you have shown are in extensions.conf not zapata.conf correct? Here is an example of a good zapata.conf.... [channels] language=en busydetect=yes faxdetect=both busycount=7 relaxdtmf=yes callwaiting=yes callwaitingcallerid=yes useincomingcalleridonzaptransfer=yes

Hi, I have already installed the X100P drivers but when I make to make call call, I always get No channel type registered for 'Zap'. Any idea how to solve this problem? It seems that the Zap module is not loaded but I have already load the driver by modprobe zaptel > modprobe wcfxo > ztcfg -vv thanks -------------- next part -------------- An HTML

Hi, Is there any command for checking the audio codec used or audio transcoding in the connected calls. thanks __________________________________________________ Do You Yahoo!? Download the latest ringtones, games, and more! http://sg.mobile.yahoo.com

Hi I thought this might be of general interest. Recently I purchased an X100P from a Digium reseller in the UK. Very pleased with the card; works perfectly. My friend (known for his deep pockets and short arms) purchased an X100P card from Ebay. He's had no end of problems with line noise, dropped called etc so I thought I would compare the two cards. Plus mine was delivered within two

I'm looking to get an x100p off ebay and am not particularly familar with the "life cycle" of the card.. An "Authentic X100P" listing has a buy it now of $29.95 and says There are 3 types of cards Asterisk would recognize: *Screenshots from the official, original driver install Cheap "OEM X100P","Clones", "Compatibles", Knock-Offs

Hi all. I`ve installed a X100P on my box and is working well with incoming and outgoing calls as a trunk with one PTSN line. I want to connect the X100P to my Panasonic 616 EASA-PHONE as an internal extension to permit to users to make calls to SIP devices from analog phones, the problem is when I dial the ext number where the X100P is connected I get busy tone. What config I need to change to

Hello my brothers and sisters, Is "X100P" card suitable to VoIP? and if "yes", am i need to only "X100P" and "Asterisk" Package? or i need also to other cards or packages? and if "X100P" card not suitable to VoIP, please recommend a another card, (please take in your account that i would like to connect standard analog line to the card

Hello, I have X100P card but exten => _9X.,1,Dial(Zap/1/${EXTEN:1}) does not work. The error is app_dial.c:803 dial_exec: Unable to create channel of type 'Zap' (cause 0) Zap show channel, lspci etc show everything is normal. Because X100P is Intel 537 modem, so can I use it as true modem for test? Did any one use X100P as a modem? Thank you very much. -------------- next part

Hello, Can the wildcard x100P be bought of the shelf in stores - say in Singapore. Thanks Varun

Hi All... I have installed a single X100P card in my PC and am playing with Asterisk. The wire I plugged into the X100P has two POTS lines on it, wired on the RJ45 in the normal way. I am getting odd behavior. It seems when I dial out that the X100P dials both lines at the same time. I have two questions. First, I see that the X100P is only a single channel. Does this mean that I can

Hello, Can anyone tell me what the "normal" number of interrupts per second is for an X100P card? I've used FreeBSD 5.3 and a linux 2.6.11 kernel on the exact same hardware (only the disk changed) and `systat -vmstat 1` on FreeBSD and `procinfo -dS -n1` under Linux. For both, I'm seeing roughly 1000 interrupts per second on my X100p card. It was a bit worse under FreeBSD, and I

PROBLEM: My x100p only does bad things. When I plug the line from the wall into the card, other phones in my house go nuts, no dialtone, crazy clicking, random tones, etc. Following the steps below, the line is screwed up any time I test after step 2. Just plugging the line from the wall into the x100p takes my other phones off line. External calls to my line hear busy. Obviously, can't

I have an X100P used, at present, largely for outgoing calls. It shares the single incoming POTS line with a number of analog phones. Is it possible to talk the X100P (Zap/1) to answer a ringing call only if I ask it to? I'd like to use only the SIP phone in my office, but let the analog phones continue to work in the rest of the house (until I can afford FXS cards anyway..) I can force

I have an ubuntu 8.10 machine. Linux 2.6.27-14-generic i want to configure a x100p card an use it with asterisk, so i download, compile and install: asterisk-1.4.24 dahdi-linux-2.1.0.4 dahdi-tools-2.1.0.2 libpri-1.4.9 i try almost everything i found on the net but without success: if i run lspci: 04:06.0 Communication controller: Motorola Wildcard X100P when i run dahdi_hardware appears this:

Hi, I'm thinking of purchasing a TDM400P card and was wondering if anyone has experienced any echo issues with phones off these cards connecting to the PSTN via the X100P cards? I have had my fingers burnt with a Voip phone > X100P. Cheers, Taff. --------------------------------- ALL-NEW Yahoo! Messenger - sooooo many all-new ways to express yourself -------------- next part

So, We want to be able to put a fax machine on the line port of the X100P in our asterisk server. We however also want to use this card for 911 calling. We need some sort of mechanisim to "disable" the line out port on the x100p by software to "interrupt a call" on the line. Anyone done anything like this?

I finally got my X100P working and now I have a question. I have several Skutch phone line simulators. My X100P works as expected with both a POTS line and an analog PBX port, but when I use a phone line simulator it doesn't answer the line. The phone line simulator doesn't power the line until the phone set goes offhook. Asterisk shows the RED alarm and then the alarm clearing but never

My setup: X100P and Quicknet PhoneJack. I can't seem to properly set up a Zap channel for my X100P. Here are some of my configurations: [zaptel.conf] fxsks=1 #X100P fxoks=2 #Quicknet PhoneJack defaultzone=us loadzone=us [zapata.conf] [channels] context=local signalling=fxs_ks channel->1 ;X100P [extensions.conf] ... [local] exten=>_NXXNXXXXXX,1,Dial,Zap/1 ;I'm pretty sure the