Displaying 20 results from an estimated 5000 matches similar to: "Help to connect to Mitel PBX via a T1 connection and a T100p"
2008 Mar 04
4
Mitel SX-200 + *
Does anyone have any experience getting a Mitel SX-200 EL/ML PBX system
to work with *?
I'm not getting inbound or outbound calls to work. (Inbound caller gets
line busy tone.)
SETTINGS FROM MITEL:
I built a Crossover cable and connected it like this:
PSTN--T1--ASTRISK--T1--OLD MITEL
-Crossover Cable Pin-out:
1 - 4
2 - 5
2005 Oct 10
2
Asterisk and Mitel SX 200 Slip and Frame Errors causing Major Ala rms
We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get
over 500 frame errors and over a 500 slip errors per hour. When the errors
reach 1000 per hour the Mitel will take it's T1 card offline. At that point
no calls can be routed from the Asterisk server to the Mitel and the TE110P
reports a Yellow alarm.
What can be causing all these Frame and Slip errors? We have been
2005 Apr 22
4
TE11OP -> Mitel 200Sx??
Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows.
Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card.
All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card.
Any advice would be great.
Zaptel.conf
span=1,0,1,d4,ami
e&m=1-23
dchan=24
2005 Oct 11
3
Asterisk and Mitel SX 200 Slip and Frame Err ors causing Major Ala rms
Eric "ManxPower" Wieling wrote:
>>
>>> span=1,1,0,d4,ami
>>> e&m=1-24
>>>
>
> Looks like you have told Asterisk to get it's timing from the Mitel.
> I'll bet the Mitel is trying to get it's timing from Asterisk.
>
> Try span=1,0,0,d4,ami and run ztcfg -vvv
>
I just set this back. It was originally set to your
2004 Apr 13
2
T100P E&M Wink Trunk
I am setting up a box with a T100P. Everything is going well. The
company I am working with has their one phone switch gear. They
provisioned me a E&M Wink T1. Cannot do PRI unfortunately. We chose E&M
so we could pass an unlimited number of DIDs to the trunk as apposed to
FXS loopstart signaling. I can make outbound calls no problem, but I am
having problems with the dial plan for inbound
2003 Jul 10
3
T1 config for robbed-bit E&M AMI
I have a couple of live T1s sitting around and they are not ISDN(like most
of the people that are using Asterisk seem to be using), they are regular
old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits.
Can I get these T1s to work with a T100P Digium card and asterisk?
Searching through the lists and the documentation I haven't seen any
examples of how to configure this kind
2004 Nov 29
1
Outbound E&M?
I've got a new setup (different building) where Asterisk is sitting
between the PBX and phone company on a E&M T1 line.
Mitel PBX <-> Asterisk <-> Phone company
Inbound works. Asterisk gets the in-band digits from the phone company
and hands the call off to the Mitel just fine.
Outbound is weird. Asterisk seems to expect that the mitel will send
routing information
2005 Aug 16
1
Does Asterisk support T1 E&M Wink/Wink voice channels on any Digium/Sangoma hardware?
Hi,
Did anyone manage to connect either Digium or Sangoma T1 card to any other
PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya
Definity to an Asterisk box with T100P and so far no luck. (I know I can do
so with ISDN PRI, but need an additional ISDN processor card for Definity.)
I tried to connect Definity to Cisco 3640 CCME (call manager express) to
test the link
2005 Feb 18
6
W&M Wink timings for Nortel
Does anyone know the default E&M Wink timings for Nortel DID ports?
The default settings on Asterisk are:
; prewink: Pre-wink time (default 50ms)
; preflash: Pre-flash time (default 50ms)
; wink: Wink time (default 150ms)
; flash: Flash time (default 750ms)
; start: Start time (default 1500ms)
; rxwink: Receiver wink time (default 300ms)
;
2004 Apr 27
2
T1 DID problem
Hello,
I have a T1 (not PRI) plugged into my Asterisk server.
Everything is working well, except I only get the first digit of the 4 digit DID in Asterisk. The T1 provider (Eschelon) tried switching to 7 digits, and I only got the first digit of the 7.
Can anybody help? We're adding another DID and I need to trap it correctly.
Thanks.
Here are snippets from the relevant files:
--
2004 Aug 31
4
T100P No D-channels
Hi
Last week I installed Asterisk (release1) with digium t100p single span T1
(wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is
currently the only user of the t1 line. All worked well for about a half a
day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I
consistently get multitudes of blue alarms on all b-channels followed by a
loss of d-channel:
Aug 31
2005 Jul 22
1
Interconnect with Mitel PBX
I have a small government department that wants me to implement a
Asterisk installation, however, they connect to the Government PBX, a
Mitel SX200, and want to keep the ability to do that. I know there is no
chance to connect the digital extension lines, but would it be possible
to have the pbx admins send analogue extensions over and have those
lines interface through an FXO interface? Or
2003 Sep 05
1
T1 - A little guidance needed to get started, What order to do zaptel, zapata...
I have about a dozen SIP phones up and working, now I want to connect the
asterisk box to our Fujitsu 9600 PBX. I currently have two dial-up servers
conencted to the Fujitsu PBX that I built with mgetty/pppd and have the
lines provisioned the same way as those dial-up server, ESF, B8ZS, and E&M
wink start, so I have confidence in the guys who set up the PBX.
I've built a loop back plug
2005 Jan 26
2
Telrad + E&M T1 Trunk
All,
One of our customers is using a Telrad PBX, we are providing
phone server through asterisk via a T1 using e&m directly connected to
the Telrad system. We're using a T1 cross cable as normal, the T1 part
works great. No alarms. When we try and dial out the Telrad using a
direct trunk group, the call fails. When looking in the asterisk console
I noticed only 1 or 2 digits are seen,
2004 Apr 07
0
Channelized T1, T100P problems
I've been having some problems getting a channelized T1 working with a T100P card. Perhaps someone can help:
I have an Eschelon T1 coming into a Vina Integrator box. This box splits out the T1 into an ethernet plug for bandwidth and a secondary T1 which I plug into the T100P card. I've connected the two with a T1 crossover cable.
I get a green light on the t100p card and can make
2005 Jan 24
2
T1 E&M vs PRI question
Ok,
I'm about to take the plunge, and am trying to decide between Channelized T1 E&M and PRI. I'm getting an "Integrated T1" which will have data and voice capability, all plugged directly into my digium single T1 card. In either case the data piece looks pretty straighforward, just setup the channel properly, hand it off to the linux hdlc layer, and route away.... the
2005 Aug 22
0
Does Asterisk support T1 E&M Wink/Wink voicechannels on any Digium/Sangoma hardware?
I could only get *ANI*DNIS* working one way and that was setting my
signalling type on the Asterisk side to 'featd' The Definity won't send
*ANI*DNIS* information back to the asterisk as far as I can tell.
Other than that, I've been running it with wink/wink E&M for a while
now. TN464 circuit pack on the definity side, te110p on the asterisk
side. Just a crossover cable
2003 Jul 05
1
E&M DID config question
I am trying to make an in/out trunk group comprised of 4 DS0's using
E&M Wink signalling. The first four channels of a DS1 on a T100P
are being used for the group. Outbound calls work fine, but inbound
calls fail. The other 20 DS0 channels are used for a PRI. Does the
configuration shown below look okay? I've tried setting 'immediate => yes'
without success, but it
2005 Feb 22
1
Astersik CVS HEAD + T1 e&m wink + IAX client doesnt detect call answered on Zap channel
Hello,
I've got very annoying behaviour from our asterisk PBX.
We have 12 channels T1 e&m wink start for TDM and using iax softphones
internally (iaxcomm, but tried firefly-thirdparty and discarded for
bad sound quality).
Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card.
In some cases when call is placed from softphone to TDM, system does
not detect call answered on Zap channel and
2007 May 24
1
Basic connection between Mitel 3300 ICP and Asterisk (trixbox) - from a clueless newbie....
Hi all,
Our company has deployed a Mitel 3300 system (only about 2.5 years ago)
and we are experimenting with setting up Asterisk in our head office
(for business continuity, ie we have a bird flu epidemic and no-one can
come in, therefore use SIP softphones at home to co-ordinate activity)
and at a remote site in the Isle of Man (connected via 2Mbps SDSL)
Ideally we'd like anyone on either