similar to: TDM400P (TDM20B) 'Freshmaker failed register test'

Mmm...I swear I read somehwere that the 7912G did SIP? Cisco lists it as an SCCP only phone? -- Undocumented Features quote of the moment... "It's not the one bullet with your name on it that you have to worry about; it's the twenty thousand-odd rounds labeled `occupant.'" --Murphy's Laws of Combat

Using X-Lite FWD soft phone, I can register, get to the 'demo' menu extension, but that's it. Audio starts, then after a few seconds stops, with packets still being passed. Anyoen have any clues? Yes there are firewalls between here and there, yes there is NAT at my end...What ports need punching, is rfc2833 the correct settign or should I use inband or info? TIA, I just

Well because I had sooo may problems with chan_agent.c I wrote this. I'm releasing it under LGPL but if you use it or anything please let me know. It'd be interesting if anyone finds this more useful than just a pile of junk. I've included a (working) example extensions file. SIP phones are assumed to have the same identifier as their extension number, but it'd be trivial to

I have read thru what other users have tried in this list when they have experienced seemingly similar issues to what I have, without success. I suspect there might be an issue regarding both the X100P and TDM04b cards being used in an Intel SE7525GP2 motherboard, as I had to even wait for a BIOS update from Intel in order to utilize my 3ware 9500 SATA raid controller on it (3ware Kb -->

I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905

I''m havign a HUGE amount of difficulty getting shoreline to work with LVS. We use it here constantly so we know it works. The problem is packets come in, get directed to a webserver, webserver returns the packet to firewall, and then it goes into a black hole. rp_filter is off globally on all interfaces. LVS seems to be working right.... I use shorewall tcrules to mark packets on

Thanks everyone for your feedback, especially Mark. I now have the ALL the files I need. My order still stands for the $8.00 product from CISCO but the CP7960 dealer sent me all the files. Now I will move on to completeing the setup of the TFTP server. Thanks again -----Original Message----- From: Michael Loftis [mailto:mloftis@wgops.com] Sent: Friday, February 18, 2005 7:51 PM To:

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output

Hi, We have two of these 4 port FXO cards. However, we are having some problems with incoming/outgoing calls. The latest version of Asterisk/zaptel from CVS is being used. Voicemail, internal SIP <-> SIP calls between Pingtel xpressa hard phones work terrific, echotest is fine, and so on. The zaptel and wcfxs modules load fine, and show all 8 FXO interfaces in dmesg:

Hi, I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 255 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 255 should be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 255 should be 2 Module 2: Not installed

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

I have a TDM400P with one FXO module and two FXS modules in it. I also have a Wildcard X101P. After trying hard to get things working on various Intel computers, but having echo problems that made it not really usable, I decided to try it on some older PowerPC (Macintosh) hardware running Yellow Dog Linux. Things started off smoothly. Both zaptel and asterisk seemed to compile okay, and both

I have an asterisk 1.2.9.1 machine with zaptel 1.2.6 running. On the TDM400P, I have 1 FXS port and 3 FXO ports. dmesg reveals: Zapata Telephony Interface Registered on major 196 Zaptel Version: 1.2.6 Echo Canceller: KB1 PCI: Found IRQ 10 for device 01:01.0 PCI: Sharing IRQ 10 with 01:05.0 Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi, I recently installed a gentoo on a PC, purchased a TDM400 and installed asterisk. Kernel is 2.6.11-rc3 First, there seems to be a problem with my system: I must put the pci=routeirq to make the card detected. The modules are loaded ok (dmesg output) Zapata Telephony Interface Registered on major 196 ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 16 Freshmaker

Hi, I have a TDM400P running with only one FXO port running on a VIA EPIA MS10000 (1Ghz Via Eden). When I run zttest from Zaptel 1.2.1 it hang and when I interrupt it with Ctrl-C that is the result: ?anyone have some idea about why isn't working? Some additional info: # /usr/src/zaptel/zttest -v Opened pseudo zap interface, measuring accuracy... --- Results after 0 passes --- Best:

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi all, I was wondering if anyone had any pointers on how to determine whether or not a module has gone wonky on the TDM400P? I have a 2 FXO (channels 3 and 4) and 2 FXS unit (channels 1 and 2). The bad (?) module in question is the FXO module on channel 3. I can't dial in to or out of that channel; dialing in gives a busy signal, dialing out just shows * hanging around after attempting a