similar to: Two questions for Asterisk setup (Definity G3R and NFAS Trunk Gro ups)

Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it

Can anyone describe the asterisk implementation of this any better than the sample config files do? from zapata.conf ; Trunk groups are used for NFAS or GR-303 connections. ; ; Group: Defines a trunk group. ; group => <trunkgroup>,<dchannel>[,<backup1>...] ; ; trunkgroup is the numerical trunk group to create ; dchannel is the zap channel which will

We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get over 500 frame errors and over a 500 slip errors per hour. When the errors reach 1000 per hour the Mitel will take it's T1 card offline. At that point no calls can be routed from the Asterisk server to the Mitel and the TE110P reports a Yellow alarm. What can be causing all these Frame and Slip errors? We have been

We've been working for the past 2 weeks to get a new V400P working with our PRIs from the telephone company. We're trying to get the Asterisk server setup as a VoIP gateway for SIP and AIX. We can make SIP-SIP calls, but all calls from or to the PRI fail. This is the applicable entries from the Asterisk log (configuration files follow) for a call coming from the PSTN on the PRI. I

Hey everybody, I've just spent the last two hours Googling and searching the Wiki. I'm trying to find if there are any listings of codes for the Avaya Definity G3R, to allow for an Asterisk system to turn on/off a phones MWI that is attached to a G3. We are looking to use an Asterisk system as a voice mail server. I'm not having any luck, anybody have such information? Thanks,

I currently have two channel groups in my zapata.conf file. I would like one group to be immediate=yes and the other immediate=no Does not seem to matter which way I go, the first entry in overrides my explicit setting for the second group. I am running * 1.0.9 on FC1 [trunkgroups] ;trunkgroup => 1,24 trunkgroup => 1,48,72 ;spanmap => 1,1,0 spanmap => 2,1,0 spanmap => 3,1,1

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

Hi All, I have just migrated from Asterisk 1.0.0 to Asterisk 1.0.5 and I have an X100P installed. The old asterisk was working, but now the new version isn't picking up any calls! However, I did notice that after installation, I performed modprobe zaptel and modprobe wcfxo and they worked fine, but when I executed ztcfg, I get the following errors: ioctl(ZT_LOADZONE) failed: Invalid

I have NFAS setup on several quad port T1 cards (Sangoma). It mostly works well with the exception that calls coming in on channels 48,72, and 96 have no audio. I tried removing these channels from zapata.conf with hopes that the channels would not come up or be used. Now I get "Ring requested on unconfigured channel". How can I busyout these these channels so that incoming

Is anybody currently running a Definity G3 connected to Asterisk via PRI and a TN464? I've upgraded today and it would appear that caller id info coming across the PRI from the Definity is no longer showing up on the SIP phones. Caller id info from the SIP phones to the Definity is working fine. I'm going to be testing previous versions of Zaptel and Libpri to find the culprit and

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

[18884732963 at from-fax-machine:... - your call is hitting the from-fax-machine context - yet your 'fax' exten is in the from-pstn-4 context. See the "[2011-03-17 13:40:29.6] NOTICE[8825] chan_dahdi.c: Fax detected, but no fax extension" line. When Asterisk detects an incoming fax tone - it tries to automagically route the call to the 'fax' extension in the SAME

I've got a system with 5 pri circuits configured into a CFAS group with a primary and secondary d channel. There are three TE410P cards in the system. The 5 circuit span are located as follows: circuit 1 on span 5 circuit 2 on span 1 circuit 3 on span 6 circuit 4 on span 2 circuit 5 on span 9 primary d chan is on chan 24 of span 5 (chan 120) secondary d chan is on chan 24 of span 1 (chan

Hey everybody, I'm looking for some information that I'm not finding by searching the 2004 Asterisk archives. I'm currently playing with a Digium T100P card and 2 Grandstream phones, things are working well. I wanted to move on to linking our Definity G3R Rev 8.2 to the T100P. Everything that I've read so far shows that you need a TN464 to accomplish this. We have a TN767E

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

Hi, I wonder if anyone is using Digium's TE110P card on an E1 connection. I have been try to, but so far it wasn't much of a success. It only works more or less in EuroISDN as PRI CPE. And even that config gives me some trouble with channel negotiation. My current config: *zaptel.conf:* span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=be defaultzone=be *zapata.conf:* [trunkgroups]

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

We fairly recently switched service providers for our 4 PRI circuits. Since that time, we started to notice some failed inbound calls. These calls terminate with an ISDN cause code 47 'resource unavailble'. Most of the time I see this error on the first or second channel on the second span in a trunk group (This is the providers trunk group for hunting, not an Asterisk trunk group). All

We've moved within the last two months to Asterisk 1.4.x All remote facilities are connected via highspeed (9mbit) connections (Over OpenVPN) to a central Asterisk box, acting as a voice router, that funnels all calls into our Avaya Definity G3R via PRI. When corporate employees visit the remote facilities and try to call the G3R's voice mail system(Audix), DTMF is not recognized unless

Hi, I have just set up Asterisk to use an E1 line with a Digium card. And I can call both in and out, but my outgoing line is all ways identifying itself as the same number, and i can't even change it to another number in the same number series. Do anyone have some clue on how to fix this. I'm using Asterisk 1.6.2.13, libpri 1.4.11.4 and DAHDI 2.4.0. /etc/dahdi/system.conf: