similar to: offtopic - channel banks

I am trying to make an in/out trunk group comprised of 4 DS0's using E&M Wink signalling. The first four channels of a DS1 on a T100P are being used for the group. Outbound calls work fine, but inbound calls fail. The other 20 DS0 channels are used for a PRI. Does the configuration shown below look okay? I've tried setting 'immediate => yes' without success, but it

HI, I have been pulling my hair out trying to get a Cisco MC3810 to interface my Asterisk box with a T1. I am able to make outgoing calls but incoing calls never reach my Asterisk box. The cisco give a fast busy when I try to call one of the DID's. When playing around with the dial-peers I can get the cisco to pick up the call, but then it forwards the call back to the ANI that is dialing.

Has anyone here used T1s with RBS with asterisk? Cary Fitch

Hi all, Muppet from the UK asking for help We are just about to have a T1 line installed in our office in Dallas and "Advantex" the supplier has sent a questionnaire asking a number of questions. I have put the question area at the bottom of the email, we will be using Digium's hardware. could anybody help :-) In the UK when I asked for a E1, number of trunks required and the

I need to know how to setup the data side of the T1 on my Linux Box. I have found information about configuring a PRI and HDLC but nothing about the Frame-Relay type setup for data. The following is information from our T1 provider. Network T1: Framing = ESF Line code = B8ZS Build out = 0-133ft(DSX)/0dB(CSU) Clock = network Pulse-density-enforce = off alarm-option = on alarm-delay = 15

All, I have done research on VoIP for some time now. I'm a Cisco certified Network Engineer however Telecom is not my strongest suit. I've been a part of this mailing list for sometime but my delusions of grandeur in migrating our 25 year old phone system to a new platform have been on the back burner, until now. I have found my company is moving to a new location(building) and this

hi, I use the oh323 driver to answer H323 calls. The connection is set up normally. In my extensions.conf file I use: exten => s,1,Answer exten => s,2,Playback(demo-instruct) exten => s,3,Hangup So that when a call is answered i get: *CLI> -- Executing Answer("H323/ip$10.0.3.23:32782/6502", "") in new stack -- Executing

How do you specify in a tablegen pattern that all destination registers are also source registers? I know I could just duplicate them, but I was wondering if there was a way it could be done without doing this. Basically an inplace operation. So for example, take a hypothetical swap w/ sqrt. if I had swap $ds0, $ds1 which swaps ds1 and ds0 and applies sqrt on the registers afterwards. Micah

Hello Everyone, What kind of hardware setup would I need to do if I want a T1 connection to PSTN and have 48 users in office with analog phones. Will something work if I have a T410P card in asterisk and have one T1 going to PSTN and other two to a channel bank. I would then connect the 48 phones (FXS) to the channel bank! Thanks. Deepak

Hello All, I'm trying to connect Asterisk to an Executone phone system with an analog DID card and I'm hoping someone can help me figure out what I'm doing wrong. The Executone DID card provides battery to the telco, when the telco wishes to dial a DID it goes off-hook, waits for a wink from the Executone and then dials the last three digits on the number with pulse (as opposed

I need a good reliable source for channel banks. Ebay is nice but too many variations of quality. I need one that can do 8 FXO and 16 FxS does anyone have a particular model, other than adtran that they can recommend??? And if possible include a source to buy from... Thanks in advance, Alex -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi Micah, On Tue, Jun 25, 2013 at 03:47:14PM +0000, Micah Villmow wrote: > How do you specify in a tablegen pattern that all destination registers are also source registers? I know I could just duplicate them, but I was wondering if there was a way it could be done without doing this. Basically an inplace operation. > I'm not sure if there is a good way to do this. The

We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get over 500 frame errors and over a 500 slip errors per hour. When the errors reach 1000 per hour the Mitel will take it's T1 card offline. At that point no calls can be routed from the Asterisk server to the Mitel and the TE110P reports a Yellow alarm. What can be causing all these Frame and Slip errors? We have been

Hey All, I'm just daydreaming here.. but what's the status of SIP-T in Asterisk? I haven't been able to find a whole lot of info on SIP-T but seems like just an extension of SIP. Right? Now if I had a PSTN Gateway (that is a SS7 gateway) that supported SIP-T, could I signal * with SIP-T from it and have asterisk utilize MGCP to sieze a particular DS0 on a remote DS1? Hmm.. What am

Does anyone know the default E&M Wink timings for Nortel DID ports? The default settings on Asterisk are: ; prewink: Pre-wink time (default 50ms) ; preflash: Pre-flash time (default 50ms) ; wink: Wink time (default 150ms) ; flash: Flash time (default 750ms) ; start: Start time (default 1500ms) ; rxwink: Receiver wink time (default 300ms) ;

I know this topic has been covered before - I just want to make sure I am understanding this correctly. | ------------------- | | | | T1 | Channel Bank | | ----------| | | | T1 Cross | | | | | | | | ------------------- -------------- | Asterisk | | | |

summary(x), where x is the output of lm, produces the expectedd display, including standard errors of the coefficients. summary(x)$coefficients produces a vector (x is r$individual[[2]]): > r$individual[[2]]$coefficients tX(Intercept) tXcigspmkr tXpeld tXsmkpreve mn -2.449188e+04 -4.143249e+00 4.707007e+04 -3.112334e+01 1.671106e-01 mncigspmkr mnpeld

Has anybody else noticed cygwin.com and sources.redhat.com being down? The machine that answers to those addresses (and sourceware.org) is refusing HTTP connections, and has been for at least 48 hours now. Anybody here know anything about it? I haven't been able to find out diddly-squat about it on the web... -J

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

I need to create a couple of tie lines between a legacy system and an Asterisk system. I was told that the tie lines are E4 Superframe E&M. I have done E&M wink but have no idea about E4 Superframe E&M and Google is not helping me here. Does anyone know about this type of signaling and if Asterisk can handle it? Thanks, Steve