similar to: T100P No D-channels

All, Alright, I've looked around the internet, the voip-info.org wiki, and browsed the contents of this mailing list. While I've found a couple of scenarios that are close to this one, I haven't found one that uses my particular card (T100P). Without further delay -- I have successfully configured internal SIP services between a Snom 200 and a Windows X-Lite client and have

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Hello, Thanks to members of the list things changed on my installation (asterisk + digium E100P with of course an E1 line). Here is my zaptel.conf : - span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=fr defaultzone=fr - Output of zttool: - Alarms Span YEL/RED Digium Wildcard E100P E1/PRA Card 0 - [root@asterisk root]# head /proc/zaptel/1 Span 1: WCT1/0 "Digium

Hi, One of my pbx's seems to be having some new issues. crackling interference on the zap channels running through the channel bank, and I noticed that these happen when I hit an "irq miss" in zttool: Current Alarms: No alarms. Sync Source: Digium Wildcard T100P T1/PRI C IRQ Misses: 82695 Bipolar Viol: 0 Tx/Rx Levels: 0/8 3 Total/Conf/Act:

I have seen this posted around the list a few times, but have never found my exact error or even a solution to this. I was getting this error every few seconds...... After moving the card to a different PCI slot and turning off some devices that are not needed. I was able to get the messages down to about every 10 minutes and the T1 card now is sitting in it's own intterupt. Apr 25 23:49:15

I have a pair of sites tied together with a T1 line running zaptel PPP on either end. The system works, but I keep getting these messages in the kernel logs, and users are reporting connection problems (TCP timeouts, and hangs) especially under high usage. --snip-- HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC

Due to some failed hardware on another platform, I've had to move a T100P card to a different chassis. After this move was completed, I am seeing some strange results on the T100P card that do not display to me any failure mode with which I am familiar. The card comes up, and shows "good" carrier and status, but Asterisk refuses to bring the D-channel up. Calls of course do

Hi all, I?ve ran into a problem regarding D-channels. I have setup Asterisk (CVS-HEAD-03/21/05-16:41:57) on RH Fedora Core 3(2.6.10-1.770_FC3) I also have a digium wcte11xp card for connetivity to the PSTN(E1). When I start zttool i see that Current Alarms changes between Recovering and Blue Alarm/Recovering. I started to see these problems after i moved the digiumcard from one PCI slot to

Hello After having installed my X100P, /proc/pci and /proc/interrupts dosent locate them. In my PCI list is it the Communication controller: Tiger Jet Network Inc ? then is dosent have a IRQ listed in /proc/pci.. All help appreciated Thanks and Regards Ajit ===========================/proc/pci================================== PCI devices found: Bus 0, device 0, function 0: Host

My PRI is being reset at least once a day with the following errors in the logs. zaptel, zapata, libpri, and asterisk are from CVS this morning.. This has been happening for weeks on all versions (including -stable). the T100P card appears to NOT be sharing an IRQ. xenon# cat /proc/interupts CPU0 0: 1203977 XT-PIC timer 1: 3 XT-PIC keyboard 2:

I have a problem which I need to resolve. We are trying to put an asterisk between a Mitel PBX and the world. We are adding Voip service via Asterisk. Here is are config files for the settings but our problem is the following. We are able to send calls to the Mitel pbx and it's the T1 connections is green saying it's ok. The support department from Mitel said that they use e&M and

Hello, I'm trying to get a Wildcard T100P working with Asterisk and so far I haven't had any luck. No problems with the card itself from what I can see and the telco says that the problem is on our end (don't they always?). A small sample of what asterisk spews out on the console: Jan 13 15:45:32 WARNING[180236]: chan_zap.c:5834 zt_pri_error: PRI: Read on 43 failed: Unknown

Hey guys, appreciate the input. Here are some thoughts. ADSI phones are out of the question. This is a business environment, I can't worry about my employees not knowing how to forward calls, answer calls when away from the multiline phone, and no ADSI phone will handle multiple lines that I have found. I would love to put 6 X100P cards in a case and run asterisk on it. but... I

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

Thank you for the suggestions Andrew. I have not come across some of them before and will give them a shot. Based on my reading, changing the motherboard should have minimal impact unless that motherboard and the TDM400P don't get along (aka. IRQ sharing). I have disabled everything that is not needed and I do not believe I have any IRQ problems and I am NEVER wrong ;). Calls are crisp and

To recap: T100P card wouldn't sync with the telco using line side clocking ( span=1,1,0.........) Had to use internal clocking (span=1,0,0.......) zttool showed Tx/Rx Levels as 0/ 1 For the grins of it I replaced the T100P card with another newer card from inventory. This newer card has the same rev on the ASIC / FPGA but doesn't have any of the various jumper headers installed

Hello * users I've problems with sound quality on zaphfc Asterisk works fine good sound quality. If I do "make load" in the bristuf.xx zaphfc dir then sound quality drops directly. Even if I don't load the chan_zap in the modules.conf I use this config on more (even old 400Mhz machines) and works correctly. Looks like an hardware problem but I can't find it. I don't

Hello, Does anybody know of a place to get a half-height PCI slot bracket for the Digium T100P card? I have an application to fit them in 1U cases for small, deployable PBX's. The T100P itself is short enough to fit in a half-height slot but I need an appropriate mounting bracket to screw it into the case. Thanks, Mark Hagler

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs