similar to: TDM400P Problems

Hi list, I have a "Wildcard TDM400P REV I Board 1" with 4 FXO modules and * 1.0.9 up-and-running. Only 2 FXO ports are used for 2 analog phones and are doing fine. I now wanted to use the 3rd and 4th port, but when I insert an analog phone, take it off hook, I do not get a dial tone. With my 1st and 2nd port, I get messages like: -- Starting simple switch on 'Zap/13-1'

I have a running * with a TDM40B board in it. I have 3 analog phones that works (rings) perfectly when connected to a Telco POTS line. When connected to the Digium TDM40B (with FXS port), I have problems with 'ringing': 1 phone 'ringes' normally 1 phone 'ringes' a bit cripled (instead of ring-ring... ring-ring..., it does 'ring-ri... ri.... ring... ri...) and the 3rd

Hi I have come across a problem, with my tdp410 and soekris board (basically pc on a chip amd geode cpu). I am using the box as a firewall/asterisk box. The problem occurs when I drop ppp and I get dead loop dectiotn going, I seem to lose interrupts and get lots of messages in syslog from wctdm24xx saying missed interrupt increasing latency its out lined here

I have a serious problem that repeats very often, after 30 - 50 calls and I can only solve it by stopped and restarting * :-( After a while, * seems to loose track of something. When an ISDN call from PBX needs to go to the Telco, I get 'Ring requested on unconfigured channel 255/255 span 2' It's always channel 255/255 ??, the 'span' number is random Setup: * between Local

Hello, Is this possible to install drivers for this hardware under FreeBSD, and begginig from which version? Motherboard Epox 8RDA3+ (NForce2) none0@pci0:0:1: class=0x050000 card=0x10001695 chip=0x01eb10de rev=0xc1 hdr=0x00 vendor = 'NVIDIA Corporation' device = 'nForce2 Memory Controller 1' class = memory subclass = RAM none1@pci0:0:2: class=0x050000

My old machine started getting a bit flaky, so I have kicked it off my desk, but still wanted to get some nouveau bugs fixed on it. (In fact it's easier now that I can reboot it more easily.) So I put a spare old hard drive on it and rebuilt it, but I'm having a heck of a time getting it working. Whenever it tries to load the nouveau module, it blows up. What's funny is that it

Hi, I have an asterisk installation with 2 E1 cards Software version is Asterisk 1.2.6 Libpri 1.2.2 Zaptel 1.2.5 I'm having problem with fax transmission, let me explain better my setup: My fist TE110P E1 card is connected to the telco line the second TE110P E1 one to an Nexspan PBX so the server is basically sitting between the line, and the pbx. every call coming from the line is

Here's one last plea for help from the list before I give up on the totally cool software FAX modem concept in complete despair (for now, at least, until I have more time to dig into it).... I am simply not able to successfully receive a FAX no matter what device I transmit from or how I bring the call into Asterisk. My lastest effort was a call from a Pitney-Bowes FAX machine into an X100P

Hi, I am new to Asterisk and have some general questions _before_ I start buying equipent to install and get everything up-and-running. (this means I have no running Asterisk (yet)). I have read already a lot of doc, but some things are not clear to me, since I'am inexperienced in Asterisk and PBX. The goal: Make PBX using Asterisk and Cisco 79xx equipment for 25 phones (1 x 7970, 4 x 7960,

Hi all, I have installed centos 5.1 x86_64. 2.6.18-53.1.14.el5 Everything seems to be working fine except that the rtc module is not working. cat /proc/interrupts shows: CPU0 CPU1 0: 129 0 XT-PIC-XT timer 1: 330797 0 XT-PIC-XT i8042 2: 0 0 XT-PIC-XT cascade 3: 4 0

Ok, Well I have narrowed it down to my mother board. It is a Biostar mother board with an NForce2 chipset. I have the Nvidia driver working on my home machine which is and Asus board with an NForce chipset running CentOS-3 and the Nvidia driver works fine. It has to be the NForce2 Chipset that is no good. I have tried updateing bios, Kernel and Xfree. There is just something with this

Hello I am using a Junghanns QuadBRI ISDN card - the module name is qozap. If I like at my interrupt assignment, qozap is sharing interrupt 10 with libata and uhci_hcd. I think libata is the IDE hard drive module and uhci_hcd is a USB module. linux:~ # modprobe qozap linux:~ # cat /proc/interrupts CPU0 0: 12634579 XT-PIC timer 1: 10 XT-PIC i8042

hi list. after my unsuccessfull experiences with mISDN i tried again to implement a zaphfc based solution. problem is: sound on calls via capi is stuttering/broken and therefore unuseable. my conf: - cel 1300, 256mb ram - avm b1 via capi connected to my outgoing ISDN - acer surf pci via zaphafc and crosslink cable with termination as internal bus - siemens gigaset 3035 as internal phone -

> Subject: Re: [Asterisk-Users] Booting error - Unable to specify channel 2: > No such device I just went through all this as well. The best thing to do IMHO is to try to find a way to manually assign IRQ in the BIOS. Also, and this is what I didn't see at first, some slots SHARE IRQ. Avoid this! If you are not using USB at all, turn it off in BIOS if possible. Tell the BIOS

Hi All, I have an equipment loaded with 4 X100P (numbered 1-4)) and one T400P (numbered 5-8). Everything works fine except that I cannot use one of the FXS ports (number 5). If I configure zapata.conf to recognize it, the whole system voice quality suffers. I've tried already to switch PCI slots, with no results. Below is a snapshot of my /proc/interrupts, maybe this can shed some light on

I have some new PC hardware I'm using with the Intel H67 chipset. I created a bzImage I use for a PXE environment for a recovery mode, installing OS images, etc. The new mobo doesn't have a VGA port but instead DVI. Everytime I unplug the DVI cable it seems to cause "Disabling IRQ #11". After that the PC is basically unusable. The /proc/interrupts shows that hdd, usb, nic,

Hi all, I am using a TDM400P card with 2 FXS and 2 FXO modules. Everything seems nice, but i'm not able to make calls nor to receive any. When I try to make a call, I keep receiven the "all circuits are busy now" message, and when I receive calls, asterisk doesn't seems to care (don't get anything on the CLI) I'm using Asterisk 1.2.17 and Zaptel 1.2.16 from Xorcom's

Excuse my ignorance here, but I am desperately trying to isolate the IRQ for my TE110P card (shown below as t1xxp) Ive gone into my bios and disabled all usb , parallel, serial and some other devices, those that I needed to keep, I have moved off of IRQ 10 and onto IRQ 5, but everytime I boot up, I get usb-uhci and ehci_hcd using IRQ 10 as well as my Digium card. Does anybody know what these are

Thanks for the reply Bill. I am aware of the interrupts problem. To solve it I have already disabled my serial ports freeing up interrupts 3 and 4 and these are allocated to the two cards. This was done 2 months ago and has not solved the problem. Is there any way that something can wake up every now and then and generate these two interrupts? My current /proc/interrupts is as follows:

I have seen this posted around the list a few times, but have never found my exact error or even a solution to this. I was getting this error every few seconds...... After moving the card to a different PCI slot and turning off some devices that are not needed. I was able to get the messages down to about every 10 minutes and the T1 card now is sitting in it's own intterupt. Apr 25 23:49:15