similar to: Set-up for 2 Asterisk System

Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any suggestions? Thanks! Craig

Management just approved purchase of a Digium T100P and a T1 card for our Merlin Legend Switch. I will appreciate comments from anyone performing this installation before: - Which T1 card did you use in the Merlin Legend? - Did you require any special interface? (CSU/DSU, etc) - Any items to watch during installation. Also we will need to remove one of our old analog Trunk cards to accomodate

Hello, I don't have any experience with channel banks and would appreciate any feedback on my theory outlined below: We have a single T1 entering the building with channels 1-12 being voice lines and 13-24 being a 768k internet connection. This T1 terminates to an Adit 600 (T1-1). Here's what I know. Channels 11-12 go out the Adit 600's 25-pair connector to a wiring block (and

Say I get an ADIT 600 with two FXS8A and one FXO8A from ebay. a. Is it good for Asterisk? b. How do I connect the extensions and lines to it? Do I need a special jack? Can I get that jack in every corner? c. where can I find help for configuring it? d. what kind of backup does it have? Does it need to be reconfigured after a power outage? Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd.

I am having trouble getting my T100P and ADIT 600 talking. I have 2 FXO 8 port cards in the ADIT and a T1 controller card. I have a T1 x-over cable connecting two together. Here are copies of the relevant bits of my zaptel.conf and Zapata.conf Zaptel.conf span=1,0,0,esf,b8zs loadzone=us defaultzone=us Zapata.cfg context=default signalling=fxs_ks group=1 channel => 1-24 My

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

Hi, I learned about shorewall a few days ago and am quite impressed with how easy it was to create a powerful firewall. I set up a test system with a cable modem and it worked flawlessly. I''m going to be building a Router/Firewall for a new T1 that will be using a Sangoma WANpipe card w/ integrated CSU/DSU to connect to a T1. Has anybody done this yet, or do you know if it''s

I have an adit 600 with one fxo card connected to a Digium single span T1 card. CallerID, disconnect supervision work perfect, however the users complain that they have some sound quality issues, after testing it I realized that whenever one is in a phone call they get like silence between the sounds coming from the other party, almost like a cell phone, in other words if there is no sound coming

Here's our config: cisco 7960's running 6.3 sip code latest cvs of * t100p zaptel card adit 600 channel bank 7 pots lines and 2 fax machines on the adit 600 dialing out from the cisco phones gets sent out via the zap channels, but I'm having some serious echo problems. I currently have the adit set to +3 rxgain and -6 txgain, with my zapata.conf containing: echocancel=128

Hello, I am currently pricing out various T1 and PRI options for a client of mine. We need voice and data - we want T's. Whether it be two seperate T's, two superate fractional T's, or one combined fractional T, we need it done. We are getting pricing and one provider is telling us that they have quality issues with the "Integrated Access" product. From what they

I'm having issues with echo. My setup is Polycom IP501 phones connected to an Adit 600 via T100P. 13 Lines going to the Adit. All echo so far is on the local side (Employees hears own voice, but only on some calls). Watching the channel with ztmonitor, I notice that TXGAIN is pegged out most of the time. RXGAIN is anywhere between 45 and 60%. Is it safe to assume that playing around

Need help...I need to install a card to terminate 7 lines...I have not order the phone lines yet...I can either do analog lines 1FBs or order a fractional T1...any suggestions on what hardware would be easier to install and configure...also if I went with a T1...do I need an external CSU/DSU or anything or does it just plug into the T1 card...thanks.. -----Original Message----- From:

Hello, I've recently purchased Adit 600 with 3FXS and 1FXO to be connected to my * server via T100P card. This is the output of "status equipment" command in the Adit600: For some reason the FXO card is seen as FXS, why? Is it ok? On the card it is written "FXO". Regards, Shlomi Bachar -------------- next part -------------- An HTML attachment was

> Hi everybody, > > This question is confusing me for some time. From selling point of view > to a customer, calling asterisk a PBX doesn't look right. According to > the definitions of PBX or PABX, Asterisk is not just PBX but much more > than that. My question is, how should I introduce Asterisk to a > customer? I don't want to call it a PBX. > > Thanks >

I'm looking to buy a channel bank. I'll be using this to basically dual a Toshiba PBX and Asterisk so that we can deploy Asterisk in small steps and have the Toshiba as a fallback in case something goes wrong. What I need is a channel bank that will allow me to take in 12 lines using the FXO ports in the CB and then output those lines to the Digium T100P. Has anyone had experience

Hi, Please let me know if you have any ideas - I am taking wild guesses now.... Here is the situation: I put in Asterisk for a local customer. I have Fractional T-1 with 12 Voice & 12 Data. I have a T100P hooked up to a TDM Card (they call it a chanel bank although it only has 2 outputs) in a CAC unit. The unit also has a router card that runs the data side. My extensions are all SIP

I have an adit 600 with an fxo card connected to a digium T1 card. If I try to make an outgoing call and the T1 cable is disconnected, asterisks returns congested like it should. But, if the adit 600 is connected to the T1 card, the adit 600 immediately "answers" the call even if there are no physical lines attached. I even removed the fxo card and the adit 600 still

I've been reading the Google searches trying to understand how to tie together Adit 600 to Asterisk to provide 2 way service. I'm about blind from reading. I assume, the answer is using MGCP between the boxes. However, the examples I found don't really explain fully enough to know how to modify examples to work for me. I'll have in the ADIT with T1's. There is a CMG and

Ok, I've pretty much decided to try the Adit route. Somebody who has experience with these tell me if I'm missing something. I have 15 incoming PSTN lines. T1 is not an option at current location. I want to put in an Adit 600 with 2 8-port FXO boards. The adit will then connect to * via a digium t1 board. I configure zaptel.conf for the T1. What other parts would be needed? How do

I'm emailing this as the customer in this case, since my carrier appears to be completely unable to solve this. A brief rundown of the problem: - We have several voice lines going through the ADIT, of course into a VoIP type of arrangement. - Voice traffic will become choppy, even drop calls completely, at random but quite often. Modem calls (which we needed unfortunately) are a joke. -