similar to: zaphfc problems...

Hi *, I want start with a setup of Asterisk with a clean PC. This PC is a SMP-Machine with two 466MHz CPUs, a Acer ISDN card and a AVM Fritz! PCI card. Which Kernel is better for my constellation (Asterisk with SMP, CAPI and ZAPHFC)? Kernel 2.6.x or Kernel 2.4.x? Regards Bastian

Hi Manfred, I applied the patch and recompiled and reinstalled and I got the folowing warning during my first test call: Aug 19 12:26:51 WARNING[294927]: dsp.c:1234 __ast_dsp_silence: zero length packet It looks like that could be the problem... and the fix! I'll let you know if the problem reoccurs. Might it be an idea to submit the patch to the bugtracker? Thanks, Gary ----- Original

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

Hi- Because a majority of my customers are in Europe, I've gotten quite used to working with ISDN (PRI) and BRI on a regular basis. Recently one of my customers asked me if I could terminate a few lines locally here in the USA (California), so I called up SBC to enquire as to how much it would cost to install a BRI here. Although the rates were reasonable (except the installation), I got

Hi, I've been learning asterisk for a couple of weeks now - and it worked for me as faar as standard configurations where concerned (sip/iax outbound/isdn4linux & capi with AVM Fritz!, Digium X100P FXO). Now I recently I'evaluating to use asterisk as a replacemnt for our companies (15 employees) legacy pbx system and I'm experiencing multiple problems with the hfc isdn cards:

Hi all- Over the past week or two, I've been trying out asterisk under Fedora 1 Linux (RedHat). In my setup (single and dual Xeon motherboards), I have so far had a very good experience in terms of performance. In doing E1 load testing, I've found that Fedora handles heavy load much better than RedHat9, probably because of its better use of the multi-threading capabilities of the Xeon.

I have * with i4l installed and working - on a dumb eicon card. It seems in order to get DTMF out of the BRI (for business banking - etc) - I should change from i4l drivers to capi drivers. wiki help seems to be for the Fritz card only...??? I have ticked the suggested boxes in 'menuconfig', explored the capi4linux websites - etc... but am missing some magic. I've "modprobe

Hello: I have found the following problems with outgoing calls with asterisk, compiled with an updated CVS on 22 Oct. 1.- Problem with retries: Whenever I set the MaxRetries parameter, to something greater than 0 in a call-fille, Asterisk ignores the RetryTime parameter and retries every file in the outgoing folder when a new call-file is copied into that folder. So, if I make a call placing

I've got Zaphfc working running Asterisk v. 0.7.2 Then I have tried with Asterisk V. 1.0 and the latest from CVS - with no succes. Has anybody got zaphfc working with newer version than 0.7.2 ? NR -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040616/32481fca/attachment.htm

Hi- I have an upcoming application that requires use of PRI channels that are primarily used for high-volume incoming traffic, but that are to be used for outbound calling as well. Of course, one option is to have dedicated outbound channels reserved, but this is an inefficient use of channel resources. Normally PBX's are designed to have the CPE yield to an incoming call if a particular

Hello- Is it possible to set the CDR record field called "accountcode" from within the dialplan? Or is there another way to cause this field to be set, preferably without using AGI code. Thanks Scott Scott M. Stingel Emerging Voice Technology Inc. Palo Alto, California and London, England www.evtmedia.com

Hi, I'm trying to setup Asterisk on a Linux (redhat 8) machine. There are no analogue phones to be used & use is purely for internet traffic (SIPs). I've followed the setup guide from : http://www.automated.it/guidetoasterisk.htm But cannot get asterisk to run. If I type asterisk at the command prompt I get invalid instruction If I type ./asterisk start I get [FAILED] Can

Hello- I'm using the "accountcode" field in cdr table to store some temporary information used by my perl scripts. I'm finding that the field seems to be truncated to 19 characters, even though the allocated field in the table is larger (varchar(45)). Anyone familiar with the asterisk sources know where I can make a change to keep this from happening? ie: to allow more

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

Hi, I have resources available to host a portal specifically for the Asterisk system, to help correlate documentation, FAQ's and How To I am new to Asterisk, and my hardest work is in locating information on using or configuring the software. Would Mark, John or any of you feel this would be of benefit to host? I am offering a PHP-NUKE portal for this, (Unless you know of a better

Hi all- Thanks to Mark Spencer for finding this patch: If you are experiencing leftover zombie processes from your AGI scripts that have terminated, this is apparently due to a RedHat 9 threading issue introduced in a recent update.... To get rid of this, try entering the following line before you start asterisk: export LD_ASSUME_KERNEL=2.4.1 It works for me - I'm still checking to

Hi- I'm almost embarrassed to ask the following simple question, following John's excellent and rigorous bandwidth analysis (see earlier thread): I have a straightforward Asterisk application, IVR-only (no connections between channels). It will simply decode DTMF's and speak prompts (probably A-Law encoded) on a number of E1 circuits simultaneously. Realistically, how many

Hello all. Since half december we are trying to implement * as our primary PBX. We had a test machine running with 2 sip phones and a single ISDN card. Since this was working ok, we installed * on our main Debian server. Some specs: P4 2.8 Ghz HyperThreading 512 MB RAM Debian Sid updated every week. Linux 2.6.9 vanilla kernel (not the debian package) 1 Intel Pro 100 nic for internal network 2

I have the latest bristuff, a zaphfc card for external calls and a PRI card for connecting to a PBX as a channel bank. With a BRI I would expect to be able to have two incoming calls going at the same time, but when I try it, one call connects and the other gives the following console message, a busy tone, and then a hangup: Mar 23 19:18:35 WARNING[5595]: chan_zap.c:7512 zt_pri_error: PRI:

Hi all- It's often mentioned here that recompiling the Linux kernel may improve the performance of asterisk. My question is: Does re-compiling the kernel have any effect if there are no changes to the configuration? What parameters will typically improve performance? Thanks for any insight! Scott Scott M. Stingel Emerging Voice Technology Inc. Palo Alto, California and London,