similar to: T400P modprobe/ztcfg failure

Hello! I am trying to set up multi-link PPP using two T100P cards in one machine, and 1 T405P card (the 4-port one) in another machine. I have previously been able to get PPP working between the two T100P cards in separate machines.... The 4-port card seems to be my problem currently. I am trying to use the tor2 driver (from a fresh CVS download this morning). When I load the driver (or run

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo

Followed the "instructions" on voip-info.org regardinging fedora FC2, making Zaptel seems to work fine, however when I modprobe I get this. It looks like a version mismatch somehow. Ideas? If this ooc, sorry first post here :-) modprobe tor2 WARNING: Error inserting zaptel (/lib/modules/2.6.5-1.358smp/misc/zaptel.ko): Invalid module format WARNING: Error inserting zaptel

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

Hi list, I have a asterisk box with an E400P that was running ok until last week. The machine just stop responding and after a reboot, the module (tor2) doesn't load anymore. anyone could help? regards Eduardo modprobe returns this: asterix:~# modprobe tor2 Zapata Telephony Interface Registered on major 196 Detected Tormenta 2 Quad T1/PRI or E1/PRA at 0xfe121800/0xfe121000 irq 7

Hello, I'm running Fedora Core 3 with udev, and asterisk/zaptel/libpri from cvs. I have followed the README.udev instructions replacing insmod with modprobe and rmmod with modprobe -r and adding the 60-zaptel.rules file, yet no matter what I do I still get this error on boot(or when I run service zaptel restart): [root@pbx ~]# /etc/init.d/zaptel restart Unloading zaptel hardware drivers:

Hi, We are trying to validate Asterisk as a media gateway PRI <-> SIP with two T400P (8 T1s) per box. The first experience with BOX1 (Compaq, 2.53 GHz, 1 Gb RAM) and just one T400P was encouraging - on the load test with 3 T1s worth of calls we had on average 75% idle CPU. Not so with BOX2 (Dell, single 2.6 GHz Xeon, 1 Gb RAM, 2 T400P) and BOX3 (Dell, dual 2.6 GHz Xeon, 2 Gb RAM, 2 T400P,

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

Hi guys, Thanks for your answers on my two questions yesterday. That's exactly what I was looking for, sorry for not noticing it myself, but I'm still getting acclimated to Asterisk and even Linux--from what I see so far, I love it. I've got another one now. Since my Asterisk install and configuration is fairly stable at this point, I'm interested it ensuring that during

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

Could anyone with any experience with * over a non-PRI T1 help this newbie? I have a fractional T1 that is working fine through a channel bank, but I can't get any response on * using a T400P. My analog line and the extensions work fine, but the T400P port 1 shows a red led (what exactly does that tell me?). I brought up zttool which shows a condition red also, but ztcfg shows nothing amiss.

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <meta content="text/html;charset=ISO-8859-15" http-equiv="Content-Type"> <title></title> </head> <body bgcolor="#ffffff" text="#000000"> <span class="postbody">Hello! <br> <br> I have a

I just received my dev kit and installed the hardware. I followed the directions Digium sends out to the letter and when I ran modprobe tor2 I got the following error: /lib/modules/2.4.18-19.7.x/misc/tor2.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the

i have error in install module of tor2. but it compile good. what happen ? ivr2:/usr/src/zaptel # make clean; make install rm -f torisatool makefw tor2fw.h rm -f zttool rm -f *.o ztcfg tzdriver sethdlc rm -f zonedata.lo tonezone.lo libtonezone.so.1.0 *.lo rm -f gendigits tones.h rm -f libtonezone* rm -f tor2ee rm -f core cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -DSTANDALONE_ZAPATA -c -o

I'm trying to load ztdummy on my Asterisk, running in a XEN domain. I've modified the code to disable the use of an RTC. I can load the zaptel module just fine, the ztdummy also loads without problem. But when running ztcfg I get this error. ----- s n i p ----- graham:~# ztcfg -vvvv Zaptel Version: 1.4.6 Echo Canceller: MG2 Configuration ====================== SPAN 1: CCS/ AMI

Hi all... I did some Google searches and didn't find any info on this so I'm posting it here... if this was recently discussed, I apologize for the duplication -- please point me to the appropriate thread. System Description: Supermicro SuperServer 5015M-MF w/ PDSMi Motherboard Intel Pentium 4 2.8 Ghz CPU 2 GB DDR2 Memory Digium T400P 4 Port T1 Card CentOS 5.1 (Final) Kernel:

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo

Hi, I have just begun working with TDMoE running between 2 fiber nics the dynamic span works great. In my main asterisk box's startup file I just 'modprobe tor2', then start asterisk. The zaptel, ztdynamic & ztd-eth modules all load by themselves when tor2 is loaded. If I stop asterisk then 'modprobe -r tor2' the tor2 module is removed but the other three remain. If I

Thanks in advance root@asterisk01:~# modprobe wcfxo /lib/modules/2.4.20/misc/wcfxo.o: init_module: No such device /lib/modules/2.4.20/misc/wcfxo.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20/misc/wcfxo.o: insmod /lib/modules/2.4.20/misc/wcfxo.o

We use dual Athlon machines with up to three T400P 4-span T1 cards. If I have more than one stick of memory (2 1GB modules or 2 512K modules, each identical), I'm getting a panic soon after I modprobe the tor2 driver. I just loaded the latest from CVS and I'm still getting the panics, which look in part like: Apr 16 14:42:28 test71 kernel: wait_on_irq, CPU 0: Apr 16 14:42:44 test71