similar to: Where to get latest SIP bootrom/firmware for Polycom IP500 phones?

Did you try to boot without lan just the power ... I've had this same problem to and rebooted the device without lan connection -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Louis-David Mitterrand Sent: woensdag 26 januari 2005 11:36 To: 'Asterisk Users Mailing List - Non-Commercial Discussion'

I've had an IP300 for a while now and it's been working fine. I just got an IP500 and when it connects to the FTP server it downloads the new bootrom and says error loading. The bootrom is fine and works on the 300... In addition, I downloaded a new copy to be sure and it still doesn't work. Can anyone give me some advice?

Hi, I'm trying to configure a Polycom IP Phone SoundPoint 500 to connect it to my Asterisk PBX but with no success. First of all, I downloaded the SoundPoint IP SIP Administration guide I found on internet and then I tried to make a boot server creating an FTP account on my Mandrake 9.1 Linux box but I needed the following files: 000000000000.cfg sip.cfg phone1.cfg ipmid.cfg sip.ld so I

Received two new Polycom 500 phones. Dhcp and ftp configured properly to load the various files including v2.5.0 bootrom.ld, etc. One of the phones loaded all firmware and config files properly, registers with *, and is usable. The second phone loads bootrom.ld (from the same ftp server on the same wire as the phone), but towards the end of the bootrom.ld load process (about 430 pkts as seen by

I'm having problems updating my bootrom to the latest (3.2.2) version. Basically, my phone starts downloading the bootrom, but I am completely certain that it doesn't actually complete the process. It gives me an "error updating bootROM!" message, but it only takes about 2 seconds to complete the download (which, because of my WAN link and FTP server environnement I know is

Hi All, We are in search of the latest Polycom firmware SIP 1.6.5 and BootROM 3.1.3as per http://www.polycom.com/resource_center/1,,pw-492,00.html Can someone help? We have legitimately obtained these phones but even our official distributor can't get their hands on updated firmware. The only thing we have found is http://www.freedomphones.net/polycom/files/?M=A which has only old versions.

I was progressively upgrading this phone from 3.1.2 to 3.2.3, then to 4.0.0. v3.2.3 worked fine, but when I went to 4.0.0 (Even adding the more specific 2345-11500-040.bootrom.ld), it won't run, and just keeps rebooting. Now I've got a really nice doorstop unless someone knows how to get out of this predicament. Help! 0925003705|cfg |3|00|Beginning to provision phone 0925003705|dns

Hello everyone, Please forgive the exclamation points but I have been battling this one off and on for about four days now. Sorry for the cross post. It all started with a box of IP 501s. I contacted my reseller and obtained the latest BootRom and SIP firmware. Unzipped, configured, copied over to my FTP server (running AstLinux, of course). The phone booted, so far so good. Updated

I am using version 1.4.1.0040 and 2.6.1.0003. I have read about newer versions out there, how can I get them? I'm having an intermittent issue regarding DHCP with one of my phones, and I recall when I loaded 1.4.1 on this one phone, it failed once, then it succeeded the second time. I am wondering if a firmware update will help. Or is there any known issues with Fedora Core 2 dhcpd and IP

I have a couple of Polycom phones, bootrom 2.5.0, SIP 1.3.1.0056. Works great with Asterisk when I power on the phone. However, after some time, say an hour, I cannot receive calls on this phone. On Asterisk, when I do "database show", it does show the phone in there, but it cannot reach the phone. Is there a way to keep alive the connection with Polycom? Any suggestions? Thanks, --

Hello, Does anybody have the latest Boot ROMs for the IP500 and IP 600 Polycom phones. I have one of each and can't find the Boot ROM v 3 anywhere to download. I would also love a good sample phone.cfg and sip.cfg files from an Aussie asterisk user to look at. Also the ip500 is having problems trying to load the bootrom 2.6.2 ? Any ideas? Kind regards Michael Felder IT Medic

Docs? Polycom has docs? Where would one find this fabled land of... err I mean Polycom does stating what ftp servers are supported? Doug. -----Original Message----- From: Ken D'Ambrosio [mailto:ken@jots.org] Sent: Tuesday, March 07, 2006 12:12 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re:

Hi, I just got my ip500 back after months of waiting. Is there an easy way to get it hooked up to asterisk without [t]ftp servers and all that or is there a quickstart page somewhere? tia r

Hey all, I'll give my reseller a call for support in the morning, but I usually have better/faster luck on the list. I've got a SoundPoint IP500 that I upgraded to BootROM 2.6.2 and SIP image 1.5.2 on someone elses advice, I forgot to change out the old config for the new when I loaded the image up (I guess the config changed a bunch between 1.5.2 and 1.3.1) I was prompted with an error

Ever since I upgraded my Polycom 500 to the newest sip.ld (kept the old bootrom), when I dial things like "*98" for voicemail, the screen shows "9*8" and doesn't dial my voicemail system! Is this user error, or errors in the new firmware? Chris Coulthurst chris@shuksan.com -------------- next part -------------- An HTML attachment was scrubbed... URL:

I don't know if Polycom decided to change their policy or not, but I just went to their website and when you click on the downlooad link, it will now present you with an option to join their extranet. I did that and I got the following message immediately: <snip> Access to certain Resource Center sections and content are subject to approval. Eligible members, will receive further

...even when I do the "factory reset" (4-6-8-* then 456). I tried using FTP and TFTP, but even though the phone uploads the log, I get these errors: 0927211350|app1 |3|00|Time has been set from 0.us.pool.ntp.org(69.60.124.59). 0927211350|cfg |4|00|Could not get all 512 bytes of the header. 0927211351|cfg |4|00|Could not get all 512 bytes of the header. 0927211422|app1 |4|00|Loaded

Hi All, I am a remote office that is connected to my office via openvpn on UDP. Voip has always worked well (after discovering g729). Initially I used a softphone, then an analog set on a sipura 2000, then a polycom IP500 (I still LOVE this phone). At that point, I started noticing that the polycom doesn't ring a lot of the time. Since I was desperate for a phone, I didn't upgrade

I got em. You want em? Anyone know how I can get these to the site listed on the Wiki? Thanks, Wiley -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050512/dfee13b3/attachment.htm

I have a question about DHCP and boot server supporting more than 1 model of Polycom phones. According to Polycom "standards", Polycom phone boots up to get a DHCP address and at the same time getting a boot server string (with username and password) to logon to boot server to download SIP, bootROM and etc. That is okay if there is only one type of phone (that requires a specific SIP