similar to: Using answering machine in my phone

So I have an X100P, and a TDM10B both working (at least I think they are). The drivers have been loaded and ztcfg -vv shows no errors in the configuration of two channels. When I run asterisk -vvvc and pick up my phone (plugged into TDM10B), I don't gear a dialtone. in phone.conf, I have [interfaces] mode=dialtone format=slinear ... Shouldn't that produce a dialtone when I pick up the

Ok. I am confused. I now have conflicting answers to my question: Do you need to use a special phone to use SIP? My setup is X100P and TDM10B. I would like to connect to iConnectHere, which uses SIP. Has anybody done this before (using similar equipment to what I have listed above)? And if it is not possible, could somebody please explain why. I don't understand why this wouldn't

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in /etc/asterisk/zapata.conf [channels]

Hi, I've got an x100P and I'm able to dial out and make phone calls with it ok but I just want to set it up to answer the phone and be a simple answering machine but it doesn't seem to want to answer the phone. I keep getting this: on the console when the phone rings: -- Starting simple switch on 'Zap/1-1' Nov 28 08:55:09 NOTICE[29298]: chan_zap.c:5458 ss_thread: Got

I have an Asterisk server running todays CVS (updated it just in case that was the problem). It has 3 X100P cards. The first two lines I use as my normal work lines and the third is my fax line which I use with SpanDSP. I run Fedora Core 4. I have a problem that the third X100P does not answer the call. From the console I can see that there is an incoming call with the following: --

I've been having trouble with a TDM10B that I installed a few days ago. At first I could not modprobe it at all (getting the errors below). I switched the X100P that was also installed (with a Motorola chip) with one with a Tiger-something chip, and then everything starts up okay. However, after a few hours, the FXS port dies (no battery or anything), and if I try to rmmod & modprobe

Hello all, New to the list, Asterisk and this wonderful world of convergence. From reading the docs, list and websites I hopefully correctly understand that I can use a plain cheap isdn4linux supported ISDN (passive) TA to hook up the PC to the ISDN line from the telco (FXO card?). Next in the PC I also need a FXS card like a Digium TDM10B or PhoneJack so I can hook up an analog phone to it. In

I am setting up my * for at home office and still have analog phones attached and answer from those analog phones and not necessarily through the pbx. I found that with the X100P cards, they see the 2nd ring and will be ready to answer the line. I used a Wait to pause and allow another 2 rings before * answers. But found that if we answer the line after the 2nd ring and before the 4th, * still

Hello, I have recently purchased a TDM400P card with one FXO expansion card, and I'm having problems. The card does not pick up incoming calls. Asterisk detects the ringing line and rings various SIP phones as required. When a sip phone answers, the sip user hears nothing and the PSTN user continues to hear ringing. Here is the asterisk output for an incoming call:

I got the devkit tdm400P(tdm10b) + x100p bundle. Where does one buy more ports for the tdm400p? I couldnt find anywhere on digium site or resellers to buy them? -Dan

I have been experiencing hung up when answering incoming calls through x100p. NOTICE[1242768320]: chan_zap.c:4584 ss_thread: Got event 2 (ring/Answered).. -- Executing Wait("Zap/1-1","1") in new stack -- Executing Answer("Zap/1-1","") in new stack -- Executing DigitTimeout("Zap/1-1"."5") in new stack -- Set digit timeout to 5 --

Hello all, There's been a consistent problem with Asterisk and a telephone line which has been answered by someone or someone that has placed an out going call. My configuration is a X100P that is plugged in with a telephone line that is split between it and a small Panasonic PBX. Asterisk is used strictly for voicemail. While the phone is off-hook, it will repeatedly go through this loop:

Hey all...I'm brand new to * and I want to convert my home into a pbx type setup. I've figured out that I want a Wildcard X100P to bring my single POTS CO into my Linux box. My problem is that I'm sure sure what I need to do to get my analog phones connected up into a structured phone system. It *looks* like I can go the route of the Cisco Analog -> VOIP for about $100 on ebay.

I'm having a problem defining my channels Here is my zapata.conf ----------------------------------------------------------------------------------------------------- ; Zapata telephony interface ; ; Configuration file [channels] ; rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes

This was submitted to the Dev list last week, but there was no response, and perhaps it wasn't the right group. I am developing an application in which I need asterisk to pass on an incoming call to a separate IVR server. The problem is that asterisk appears to hang up while the IVR is playing back a sequence of recorded voice and systhesized voice prompts. My setup is: Analog line

Just installed the new 4-port FXO card and moved two pstn lines from existing x100p cards to ports on the FXO card. All zapata.conf entries that were functional on the x100p's were copied to the new FXO channels (including callprogress=no). Observations thus far: 1. asterisk will spontanously decide a pstn call has arrived, and ring the sip phone designated in the dailplan. Verified

I have a TDM-400P with one FXO module. On an incoming call, I have set Asterisk to dial my phone (exten => s,1,Dial(IAX2/carey)), which is basically the only thing in my dialplan. When the call is answered by the PSTN phone first, or when the ringing call is hung up, Asterisk keeps ringing for 5+ seconds, which causes trouble (the answering of already answered calls). I noticed in the

In having configured my first * server there are a few questions I could not understand or find answers to 1) How does one use ztmonitor to adjust the rxgain and txgain. I have set mine to -1.0 each to get rid of echo on std phones connected on the TDM10B FXS module 2) Is it best to use a TDM card with an TFX and FXO module or is the the FXO = X100p and FXS on TDM a good method? 3) How do I

I'm having with an echo or delay I connect to the PSTN with a x100p and then connect a std. phone to a FXS module on a TDM10B. The std phone is only 2-wire so I know this is not helping. (yes I have read the 2-wire 4-wire issue) I have tried many echocancel values. The best thing to help was rxgain and txgain. below is my current zapata.conf file All help would be grateful. I have tried