similar to: x100p and groundstart signaling - help

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Callerid issue 1) if you run ztmonitor on the fxo line & call in do you hear the fsk tone if yes then we beleive the CAC is passing fsk 2) in chan_zap->ss_thread around line 4154 (current cvs) if you get to the callerid_feed at least once then if you get to chan_zap->ss_thread->callerid_get around line 4163 (current cvs) does this parse fail

Hello Astrites, I was just about to send out a long email about not being able to detect hang-up with my CAC II FXO module on my PSTN POTS lines. I had tried many configurations. I had attached a toner to the line to see if I was getting this "disconnect supervision" signal after hang-up. (toner has a line powered light in the off position) It seemed that I was getting the signal,

I am having a problem using the Adtran 750 FXO quad card with a Groundstart trunk line. I am able to receive calls on the trunk line, however dialing out is not working. The Adtran does not seem to be doing the signaling. Has anyone used the 750 FXO card in Groundstart mode? Any special configuration issues that I should be aware of? Syed Akbar Alico Systems Inc www.alicosystems.com Tel:

Hello! Recently I posted a question about an installation I have that was experiencing glare problems. The solutions presented were to use inverse inbound and outbound line groups and to use groundstart signalling. As it turns out, the Sangoma A400D card that is in use does NOT support groundstart. I've confirmed this with a Sangoma engineer and their support staff. I've also read that

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

hi i need help in connecting a X100P-clone in germany. Basic questions: a)what configuration do I need ? what is the difference (maybe explain in german? via email?) fxs_ls: FXS (Loop Start) fxs_gs: FXS (Ground Start) fxs_ks: FXS (Kewl Start) b) can I use one card for connecting to the telephone network (in this case my analog pbx) and the same card for connecting an analog phone

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1

Hi, It's been forever since I dealt with POTS lines. We have a client that needs FXS and FXO support. If memory serves correct we used the TDM400P with fxs_gs/fxo_gs. What's the equivalent of that card today? TIA. Dovid -------------- next part -------------- An HTML attachment was scrubbed... URL:

A thought occurred to me to on how to further quantify the impact of "glare" on a properly dimensioned trunk group and debunk the ground start glare concern. A cursory traffic analysis clarifies: 1. Assume you have a two-way trunk group, dimensioned for average busy hour, average busy season for P01 grade of service, Erlang B or Poison distribution. 2. Further assume that the

I tried adding wwww to my dial string... It appears to not made any differnece. I see by watching show channels that the w's are there in the dial. I have this box connected to bell south down in georgia. I have an identical box connected in indiana. The box in indiana works fine when dialing out. When in GA dialout is getting "you must first dial a 1 to place this call". show

Anyone have recommendations for a gateway / ATA for business that can do GroundStart? Preferably with an rj-21 - but okay if not.. -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20110614/42cbd90d/attachment.htm>

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

I am having a problem with Red Alarms on X100P cards. The most frustrating thing is I can not duplicate the alarms, therefore am not sure how to solve it. I have read after searching posts and the web that you can try different signaling methods which may help alleviate the problem. There is fxsks (Which I am currently using), fxsgs, and fxsls While reading the Digium site about these different

I bought an Aastra PT480 from digium, but I wanted to see if I could get some more help with this before Monday. Any help would be appreciated. I have the phone connected to the TDM400P card, and I also have the T100P and the X100P in the same box. My problem is, it appears as if the phone and asterisk can't understand each other. The port the phone is connected to always remains

Hi, I have a TrixBox install with a Sangoma A200 and 4 FXO ports, there are 3 BT lines connected directly to these ports. One of the lines has BT FeatureLine Compact and this is the line I am having problems with, the other 2 lines are working perfectly, detecting CID, answering incoming calls and placing external calls via SIP devices. I am receiving a error log entry: chan_zap.c:

List, I just tried to swap out our 410 for a 411 and we started have problems with on of our T1's. Setup: Span 1 - Dedicated PRI for long distance. Span 2 - 12 channels fxs_gs outgoing local. 12 Channels em_w incoming DID's. I didn't have any problems with the PRI. The trouble was with the T1. We were unable to place any local calls, and all incoming DID's where garbled.

Has anyone had any success with the Rhino CB-24? I can't get mine to work, I tried all the obvious settings. The cb-24 gets stuck at init ESF framing, as if it's not seeing the t1 card at all. It does get a t1 carrier (detecting voltage??) Help! Thanks.. Everything appears to look good on the server, I did: [zaptel.conf] span=1,0,0,esf,b8zs fxogs=1-24 [zapata.conf] signalling=fxo_gs

Hi everyone, I've just got my X100P card installed and working but there seems to be an issue with hang-up supervision. If I stuff a call out over the X100P card onto the PSTN that's fine. When I hang up the SIP phone the PSTN call ends. If I receive a call from the PSTN, it's answered and everything is ok until the remote party hangs up. Asterisk thinks the call is still active and