similar to: Access Bank 2 <---> T100P T1 Cable.

Displaying 20 results from an estimated 4000 matches similar to: "Access Bank 2 <---> T100P T1 Cable."

2003 Oct 16
3
Adtran TA750 & T100P
Hello, So all the pieces are finally here, and I'm ready to play. I remember reading on this list that the connection Channel Bank <-> T100P requires a "reverse cable." Is this a regular Ethernet reverse cable (i.e., only a couple of pairs reversed?) Please help me before I blow something up! Saludos, Jose.
2004 Aug 24
3
Asterisk with Adit 600
Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any suggestions? Thanks! Craig
2003 Oct 14
2
Digium should develop and sell just Dummy card. For timing...
I'm first to buy 5 pack. Even for > $30.
2004 Aug 29
0
Static Problem (t100p - Channel Bank)
Hello, We keep having a really bad static problem on phone calls completed using a Adtran TA750 and T100P card. The phones are Polycom IP 500 phones and, it occurs across all phones. Not just one. Everything appears to be on it's own interrupt. I noticed the last time we did this, we rewired everything to make sure it wasn't an electrical issue. Well about a month and a half later
2003 Sep 02
1
Configure DID Numbers with T1 Line & T100p
Hello Everyone, I am new to asterisk and linux too, I managed to installed asterisk on redhat8 with the help of mailing list archives and Handbook guide. I configured 2 SIP phones (grandstream) and it is working fine internally. We have T1 Line coming in with block of 200 DID Numbers. I want to assign DID Numbers to each of SIP phones as an extensions and able to call any PSTN line.
2004 Apr 07
0
Channelized T1, T100P problems
I've been having some problems getting a channelized T1 working with a T100P card. Perhaps someone can help: I have an Eschelon T1 coming into a Vina Integrator box. This box splits out the T1 into an ethernet plug for bandwidth and a secondary T1 which I plug into the T100P card. I've connected the two with a T1 crossover cable. I get a green light on the t100p card and can make
2004 Sep 07
0
T100P problem with LD T1
I've got a dedicated LD T1 terminating to a DMS100 switch. My outgoing calls aren't working, on the switch side they see two sets of dialing, with the first three digits repeating. I've used the sample extensions.conf modified a bit to remove the 9 and the 1, like so: [trunkld] exten => _NXXNXXXXXX,1,Monitor(wav,/tmp/dial) exten =>
2004 Oct 01
1
Help to connect to Mitel PBX via a T1 connection and a T100p
I have a problem which I need to resolve. We are trying to put an asterisk between a Mitel PBX and the world. We are adding Voip service via Asterisk. Here is are config files for the settings but our problem is the following. We are able to send calls to the Mitel pbx and it's the T1 connections is green saying it's ok. The support department from Mitel said that they use e&M and
2007 Oct 26
4
Need T1 crossover cable?
I'm connecting a T1 PCI card to a Nortel Option 61 switch T1 card. My Sangoma A102D shipped with 2 T1 cables - which I assume are straight through. Do I need to make crossover cables for this scenario? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20071026/9cea5e74/attachment.htm
2004 Apr 30
1
T100P & Integrated (D&V) T1 -> Public IP Range
Hello, I have a T100P card on a Red Hat 8 machine with Asterisk installed on it and I'm trying to get the data routing properly through it. I purchased an Integrated Data/Voice T1 Line with channels 1-6 voice and 13-24 data. The line is plugged directly into the Asterisk machine's T100P card. Previous to the asterisk set up we had an Adtran router that connected everything to what the
2006 Apr 24
1
Re: Shielding of T1/E1 cables WAS RE: PinoutsforT1/E1 crossover
> Close. 10/100mbps Ethernet uses wires 1,2,3,6 but that is pair 2 & 3. > Pair > one is the pair up the dead center (pins 4&5), pair 2 is pins 1&2, pair 3 > is > 3&6 and pair 4 is 7&8. A T1 uses pairs 1&2, which is why you can't use a > regular crossover cable for a T1 crossover, but you can use a regular > ethernet patch cable as a T1 patch
2004 Jan 26
2
Need Europian vendor for Digium hardware.
Must accepts wire transfers and ships to Sofia. Thanks
2003 Oct 31
2
Which ADSI phones to buy?
I just need to buy 5-6 ADSI Phones. I wondering which of these models to choose - aastra 390 - I don't know is this an ADSI phone at all. Is there versions with and without ADSI - aastra 350 - I'm sure that it have ADSI. If there is some other good working model, it will be great, if someone points me. Thanks
2008 Nov 12
2
AS5200 <-> T100P - No alarms but no calls either...
Greetings, I have a AS5200 that I have interfaced to a T100P via a T-1 Crossover cable. I got it where the alarms are all ok/green but I'm unable to dial out or dial into the AS5200. Anyone have any suggestions as to where to begin troubleshooting this?
2003 Jul 21
1
Best E1 channel bank?
Need to buy 2-3 channel banks for some asterisk deployments...
2006 Apr 24
1
Re: Shielding of T1/E1 cables WAS RE: Pinoutsfor T1/E1 crossover
> I've never bothered to check to see if cat5 cables use the appropriate > mating twisted pairs or not. Since the pinouts are different for cat5 vs > T1 cables, I'd have to guess a single strand is used from two different > twisted pair groups. That wouldn't be cool, but in short runs it > probably doesn't have much of an impact. > IIRC, standard Ethernet uses
2004 May 25
1
Problem - Adtran TSU 600, t100p
Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs
2004 Jan 01
1
Newbridge Mainstreet 3624 T1 channel bank now Alcatel
Hi I just came accross this Newbridge Mainstreet 3624 but the Alctel site appears to have zip for reference/user manuals Anyone by chance have 1 of these or a url for the docs ? thx
2004 Aug 22
3
asterisk T100P to Merlin Legend
Management just approved purchase of a Digium T100P and a T1 card for our Merlin Legend Switch. I will appreciate comments from anyone performing this installation before: - Which T1 card did you use in the Merlin Legend? - Did you require any special interface? (CSU/DSU, etc) - Any items to watch during installation. Also we will need to remove one of our old analog Trunk cards to accomodate
2009 Sep 04
3
T1 TE121 cable connected to a TN2464BP AVAYA card
Hello All I am looking for the cable I need to create to connect a TE121 card with a TN2464BP card (AVAYA ISDN Card), please let me know if someone have the information about this cable, my asterisk CLI show this: pri show span 1 Status: In Alarm, Down, Active And the card is in red, so I am thinking the problem is the card. Any idea??? Thanks John Teleperformance values: