Displaying 20 results from an estimated 4000 matches similar to: "E100P"
2004 Jun 29
2
T100P-E100P circuit board differences
Hi-
Perhaps someone with an E100P in hand can answer this:
I just received an E100P from Digium (I normally buy quad boards)
I noticed that the circuit board says "T100P" on it, and I assume that the
T100P and E100P both use the same circuit board.
Can someone please confirm that their E100P says "T100P" on the artwork?
Thanks
Scott
Scott M. Stingel
Emerging Voice
2003 Dec 29
1
E100P pinouts anyone?
Just cross pairs 1-2 and 4-5
1 <--> 4
2 <--> 5
Never done an E1, but I think it's the same for a T1 4 wire cable.
Tim Thompson
Commercial Sales Engineer
http://www.amatechtel.com
(806) 722-2227
-----Original Message-----
From: bam [mailto:bam@cqm.co.uk]
Sent: Monday, December 29, 2003 9:12 AM
To: asterisk-users@lists.digium.com
Subject: [Asterisk-Users] E100P pinouts
2005 Mar 08
2
Connect asterisk on classic pbx with T100P card
Hi,
I try to connect my asterisk box with a classic pbx
(Siemens).
I have a T100P E1 card.
modprobe zaptel and wct1xxp ok
ztcfg -vv ok
I can run asterisk and show the channels but the led
still flash red
My zaptel.conf :
span=1,1,0,ccs,hdb3,crc4
bchan=1-15
bchan=17-31
dchan=16
My zapata.conf :
;; E1
switchtype = euroisdn
signalling = pri_net
group = 1
context=e1
channel => 1-15,17-31
2004 Sep 03
5
Digium E100P and PMX in Germany
Hello ml,
i need some help on my zaptel configuration. My E100P only shows some
YELLOW / RED alarm when I load the wct1xxp module and do a
cat /proc/zaptel/1
Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED
...
..
.
My /etc/zaptel.conf is:
span=1,1,0,ccs,hdb3
bchan=1-15,17-31
dchan=16
loadzone=nl
defaultzone=nl
I tried zaptel-1.0RC2 and the latest CVS
2004 Nov 23
1
Error when install E100P
Hi, all
I am trying to install E100P card, the 'modprobe zaptel' is ok, but
when I did 'modprobe wct1xxp', I got such error, so can not load the
driver for the card.
/lib/modules/2.4.20-8/misc/wct1xxp.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters,
including invalid IO or IRQ parameters.
You may find more information in syslog
2003 Dec 19
1
E100P connected to Cisco
Hi All,
I wish to connect * to a Cisco using a E100P board.
When I load the driver I got this error message:
-bash-2.05b# modprobe wct1xxp
ZT_CHANCONFIG failed on channel 1: Function not implemented (38)
/lib/modules/2.4.21-SAX/misc/wct1xxp.o: post-install wct1xxp failed
/lib/modules/2.4.21-SAX/misc/wct1xxp.o: insmod wct1xxp failed
Follows Cisco configuration:
isdn switch-type primary-qsig
2004 Jan 04
2
Two E100P boards - could not load zaptel module - Channel 63 - no such device
Hi,
I have two E100P boards connected to my PC. I wish to setup two
E1-ISDN-PRI lines, the first SPAN with 15 channels and the second one
with 30 channels. When I try to load zaptel modules, I get an error message:
"Loading zaptel framework:
Loading zaptel hardware modules: wct1xxp wcusb
Running ztcfg: ZT_CHANCONFIG failed on channel 63: No such device"
Follows my zaptel.conf:
2003 Sep 18
1
e100p and E-bit alarm indication
We connected an * box with an e100p to an E1/PRI from a telco here in Italy.
After we had it working perfectly the telco told us that, despite the circuit
appeared to work fine, and we could place calls on it, they had an "E-bit2
alarm indication constantly on that caused the circuit to be flagged as
"faulty" every time.
(The E-bit indication, is an alarm sent back from us to
2003 Jul 11
7
ISDN PRI E1 configuration with E100P
<P>hi Everyone,</P>
<P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P>
<P>*CLI> <BR> == D-Channel on span 1 up<BR> -- B-channel 1 successfully restarted on span 1<BR> --
2003 Aug 12
1
new on E100P
Hi, I'm installing my first E100P.
My zaptel reads the following:
Span=1,0,0,ccs,hdb3,crc4
E&m=1-31
My Zapata.conf reads the following:
Signaling = em_w
Channel =1-15
Channel =16-31
After starting the zapter service I get:
ZT_SPANCONFIG failed on span 1: No such device or address (6)
???
PauloHM
-------------- next part --------------
An HTML attachment was scrubbed...
2003 Jul 07
1
Getting Started with Digium T100/E100 cards
Just purchased a couple of T100 and E100 cards in order to interface from
our company's proprietary system through a linux gateway. I am new to
Asterisk and Digium.
After installing the T100 card, I went looking for drivers for this card.
Are the drivers built into the Asterisk application? If so, how do I enable
the card through Asterisk?
Are there any good getting started documents for a
2004 Jul 05
2
T1 configuration, getting help via IRC?
In my * server I have a T100P, connected with a T1 crossover cable to an
Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the
alarm on the card starts blinking red. Running zttool confirmed that
yes, it is a red alarm. I've read a few previous posts on this type of
setup and I'm not too much closer. What should I be checking next? A
different cable? The
2004 Apr 29
2
e100p installation
Hi, I buyed a wildcard e100p and I installed that but when I load asterisk I
have this error:
Apr 29 18:59:25 WARNING[8192]: chan_zap.c:690 zt_open: Unable to open
'/dev/zap/channel': No such device
Apr 29 18:59:25 ERROR[8192]: chan_zap.c:5403 mkintf: Unable to open channel
1: No such device
here = 0, tmp->channel = 1, channel = 1
Apr 29 18:59:25 ERROR[8192]: chan_zap.c:7526
2004 Dec 03
3
Two zaptel T1 cards: no clock from one
List,
I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel
bank). I cannot seem to get the T100P to send any clock to the
channel bank. I prefer that it use the same clock source as the
TE410P, but it doesn't matter if it's not in sync just as long as it's
there.
The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to
XO Sonus switch, the net to
2004 Jan 01
2
How to load the driver of TDM400P card!
Hi!
I have just bought the X100P and TDM400P cards to install on my computer
to implement the PBX. I also downloaded the newest softwares
asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on
my computer (Red Hat Linux 8.0). All packages are compiled well. When I
use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo,
modprobe
wcfxs), the first two (zaptel,
2004 Dec 22
1
PRI error (HDLC Bad FCS)
Hi,
We currently have an Asterisk box (P4 2.4 Ghz, 512Mb RAM, 1 T100P,
Zhone Channel Bank and 1 E100P) connected to an ISDN running without
any problems. That machine is working for about 1 year.
Two days ago, we decided to switch that machine for two PowerEdge 600SC
(HA) and we got some problems.
The running machine (P4 2.4Ghz) has an Intel motherboard with four
32-bit 3.3v PCI slots,
2003 Aug 25
4
T100P/ TSU 600 installation problem
I have just received a T100P and an Adtran TSU 600 in
the mail.
I seem to be having a problem with the T100P card. So
far I have done the following:
vi zaptel.conf
fxoks=1-22
fxsks=23-24
...
vi zapata.conf
...
signalling=fxo_ks
...
channel => 1-22
...
signalling=fxs_ks
...
channel => 23-24
I then run
modprobe zaptel
modprobe wct1xxp
ztcfg -vv
There are no errors to report. In
2003 Nov 18
3
hold music =]
Hi All,
Just installed our very first asterisk system, and we love it! I cant
believe the different things you can do with it, just great =]
My question is: How do I configure my system to play an mp3 file when a
caller gets put on hold?
Thanks in advance,
Steve.
2004 Sep 13
1
Red Alarm - Config Zaptel card
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040913/52b2ac04/attachment.htm
-------------- next part --------------
hi all,
can anyone give solution for this.
?wct1xxp - Digium Wildcard T100P T1/PRI Card 0
zttool gives
RED Digium Wildcard T100P T1/PRI Card 0
my zaptel.conf look like this
span=1,1,0,esf,b8zs
2004 Sep 13
1
(no subject)
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040913/22b214e9/attachment.htm
-------------- next part --------------
hi all,
can anyone give solution for this.
?wct1xxp - Digium Wildcard T100P T1/PRI Card 0
zttool gives
RED Digium Wildcard T100P T1/PRI Card 0
my zaptel.conf look like this
span=1,1,0,esf,b8zs