similar to: Voicemail volume

I wonder if anyone else's Asterisk box drops the connection to voicemail after 30 secs even when the maxmessage parameter is set to 180 (3 mins). Here is the general section of my voicemail: [general] ; format=wav49 maxmessage=180 attach=yes Even if it only gave the caller 30 sec to leave a message it would be nice to tell the caller that they have run out of time before ending the

I was looking at the sample "follow me" config (http://www.voip-info.org/wiki-Asterisk+Tips+follow+me <http://www.voip-info.org/wiki-Asterisk+Tips+follow+me> ) which uses a dial modifier 'c' to enable Answer confirmation - "If the letter c follows, then "Answer Confirmation" is requested, in which the call is not considered answered until the called user

Hello: I have read that music on hold requires a timing source (which I never had to worry about previously since the server had zaptel hardware in it)...now I'm configuring a server in a colo which has no zaptel hardware. If I use the dialplan to run MusicOnHold(), I do get the music upon dialling that extension, but if I try to use the hold button on either a 7960 or X-Lite I get

Since upgrading to 7.2, I've noticed a random problem where I dial a number and hear all the correct tones in the handset, but the display won't show all the numbers I dialed. So you sit there waiting for the dialplan to kick the call off (b/c you heard the proper amount of tones played and think it's all good) but the phone is just sitting there b/c it somehow "missed"

> I too contacted CDW about the $9.37 Cisco support > contract. But because I did not buy my phone from them I was > not allowed to purchase it. The vendor I bought the phone > from does not provide them. What are the "magic words" to > get CDW to sell it to you? With all of this hassle I highly > doubt that I will buy more Cisco phones anyway. After >

Can anyone help me to understand what the significance of this output is? May 17 10:50:23 DEBUG[2030]: Didn't get a frame from channel: SIP/105-1ae4 May 17 10:50:23 DEBUG[2030]: Bridge stops bridging channels SIP/105-1ae4 and SIP/outbound-7dc3 I searched for these phrases but am coming up short on what they really mean. I'm trying to investigate problems we are having with two

Hello everyone, I playing around with ENUM and have configured * to query a few sources for testing purposes (fierymoon, e164.arpa, e164.org). I'd like to know if there is a way to query these servers manually (ie outside of asterisk via nslookup or equivalent) to find out if particular exchanges are listed with wildcards, so as to terminate calls to those prefixes (I'm not trying to

Hello everyone.... Searching the archives and google always comes up with entries regarding the "dyn" dns option in the 7960, but I can't find answers to my specific question.... My 7960 is connected via cable modem and is NAT'ed (everything is working fine). On the 7960 under SIP configuration\NAT Address I have the public IP of my cable connection. Comcast gives me a

Does anyone know if the 7912G (which the wiki says can do either sccp or sip) uses the 7940/60 sip firmware? I ask this because the only firmware I can seem to find on TAC for the 7912G is sccp, no sip...if it takes it's own firmware and doesn't use 7940/60 firmware, can someone point me to the right location for it? Thanks, Marty Mastera M3 Resources marty@m3resources.com Phone:

For some reason I can't get the Dial command 'C' flag to work. The calls are recorded in the CDR with the 'C' on. Does anyone have an idea? extensions.conf: exten => 114,1,Dial(SIP/114,,C) It shows in the lastapp: cdr: | 2004-10-05 13:16:02 | "112" | | 114 | intern | SIP/112-3fb6 | SIP/114-0e7a | Dial | SIP/114||c | 6 |

We are having an issue with the SPA962/932 combo where the phone and the sidecar will reboot unexpectedly ? could be onhook, could be on a call, doesn?t seem to matter. I read that certain early firmware revisions could cause this so I?m running what was a week ago the newest available (5.1.18). A call to Linksys support suggested that I ensure that the phones are using a recent firmware version

Any recommendations on an economical layer 3 switch? Preferably something that you have hands on experience with connecting to IP phones with attached PCs? Specifically I need the ability to set the VLAN in the phone to tag voice packets and to set a native VLAN on a per port basis on the switch to put the untagged packets from the attached PC into a separate VLAN. POE is not a requirement

Hello, I don't have any experience with channel banks and would appreciate any feedback on my theory outlined below: We have a single T1 entering the building with channels 1-12 being voice lines and 13-24 being a 768k internet connection. This T1 terminates to an Adit 600 (T1-1). Here's what I know. Channels 11-12 go out the Adit 600's 25-pair connector to a wiring block (and

Hello everyone, Having recently gotten Broadvoice inbound DTMF to work (thanks Greg)...I am now running into a frustrating problem...when a call comes in to the BV number via a cell phone (tested with 3 different cell phones; albeit all on T-Mobile) the beginning of the IVR welcome audio is cut off. A call placed via a landline phone over the PSTN to the BV number does not exhibit the problem.

Hello, I'm looking for any comments or user experiences from anyone who is using 7912G phones with SIP. Any installation issues? Usability problems? Do the features seem to work, etc...In short, I'm looking for your opinions on how suitable this phone is for an asterisk implementation for approx. 10 users. Next logical question: what other phones would you recommend for a situation

Ok, ok, I know there has been plenty of discussion on asterisk and fax - from this I understand: 1) First and foremost, use g.711 ulaw 2) Packet loss, etc...makes faxing over the internet unreliable My need is for a fax to come in on a X100P and be forwarded to a fax machine on the local lan. I don't currently have any fxs as I'm using all sip phones at this point. I see the

I understand there has been some issues sending DTMF tone through Broadvoice. Can some provide me with symptoms? --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.700 / Virus Database: 457 - Release Date: 6/6/2004

I have read several posts regarding this problem but can't find one with a solution... I see the same issue: Voicemails picked up by handset have normal volume, but voicemail sent as a wav attachments in email are so low they are barely usable... Is there a way to fix the volume before they are emailed out? Thanks for any tips.

Grasping at straws here...is anyone using a Dell PowerConnect 2224 24-port unmanaged 10/100 switch in a deployment? I have two separate asterisk installations with bad one-way audio where the only common elements left are the Dell switches and Polycom IP-500 phones. Two different ITSPs - one location uses IAX2 to the outside world, the other SIP. Two different bandwidth providers, one SDSL 1.5

Hello, I've just set up Asterisk with a TDM400P (specifically, a 'TDM22B bundle' - 2 FXS and 2 FXO, although I'm only using one of each interface at the moment, in case that's relevant) The problem I'm getting is that when I listen to a voicemail message, the recorded message is played back at extremely low volume. All the supporting prompts are at the correct volume,