similar to: odd behavior - adtran ta 850 + t100p

I am using the following macro to dial a ZAP channel. When I dial in, * answers and I go to voicemail. I never hear any ringing, though. It doesn't work with the Ringing command before or after the Dial command. [macro-zapdial] ; ; call a ZAP extension for ${ARG2} seconds, and then voice mail ; ${ARG1} - Extension ; ${ARG2} - Time to ring exten => s,1,Dial(ZAP/${ARG1},${ARG2}) exten

Hello. I'm trying to transfer calls from an analog phone (Zap/1, TDM400P card) to some other terminal connected to my Asterisk PBX. If I make a flash hook pressing the phone hangup button quickly it works as expected, I get a new dialtone and the other side is put on hold. But I would like to use my phone's "R" key instead for some different reasons (it's quite easier to use

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Hopefully someone here can save my sanity. I have been trying to solve this problem for days now, but just cant put my finger on it. Im new to * so I have probably done something stupid! I have a TDM400P with one FXO module and a FXS module. The main problem I have is not being able to get the extension attached to the FXS module to ring or be able to make calls. It gets a dialtone fine but I

Hello, I ordered the Devel lite kit, and installed it. I am just trying to get the FXO port to work, and am having trouble. To load the card I do the following. modprobe wcfxs modprobe wcfxo ztcfg -vv asterisk -vc My /var/log/asterisk/messages show Nov 3 11:03:39 WARNING[3317]: zt hook failed: Device or resource busy Here is my /etc/zaptel.conf fxoks=1 fxsks=4 loadzone=us defaultzone=us

I am having a problem using the Adtran 750 FXO quad card with a Groundstart trunk line. I am able to receive calls on the trunk line, however dialing out is not working. The Adtran does not seem to be doing the signaling. Has anyone used the 750 FXO card in Groundstart mode? Any special configuration issues that I should be aware of? Syed Akbar Alico Systems Inc www.alicosystems.com Tel:

Has anybody had any luck getting an Adtran Total Access 616 working via the Ethernet port/MGCP to an * box? The voice lines don't seem to be coming up and I wasn't sure if I had something missing. Here's my mgcp.conf file: [general] port = 2427 bindaddr = 0.0.0.0 [10.189.189.31] context=nicktest host=10.189.189.31 canreinvite=no line => aaln/1 line => aaln/2

I have a channel bank (TA750) and a PRI with 30 channels connected to a TE405P, in the channel bank I have a extension to a fax machine, but it doesn't work to send or receive fax. There are any advice ? Kind regards, Miguel

To recap: T100P card wouldn't sync with the telco using line side clocking ( span=1,1,0.........) Had to use internal clocking (span=1,0,0.......) zttool showed Tx/Rx Levels as 0/ 1 For the grins of it I replaced the T100P card with another newer card from inventory. This newer card has the same rev on the ASIC / FPGA but doesn't have any of the various jumper headers installed

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

Hello Can somebody send me please config files of zaptel.conf and zapata.conf for adtran fxs ports. I cannot make it work. I do not get a dial tone on Adtran and when I am trying to call from sip i get: app_dial.c:674 dial_exec: Unable to create channel of type 'Zap' == Everyone is busy at this time There are no errors on T100P and adtran. Please help! B.

I?m pretty new to * but it?s got my vote so far. I?m trying to test calls coming into my system but * won?t do anything useful with the call. There are no errors when starting * but the following is received when I try to call the machine over a channel of a T1: *CLI> -- Starting simple switch on 'Zap/1-1' -- Starting simple switch on 'Zap/2-1' -- Hungup

Hello, So all the pieces are finally here, and I'm ready to play. I remember reading on this list that the connection Channel Bank <-> T100P requires a "reverse cable." Is this a regular Ethernet reverse cable (i.e., only a couple of pairs reversed?) Please help me before I blow something up! Saludos, Jose.

I have a T100P card connected to an Adtran and then a T1. I have added the following configurations to Asterisk...but, when I dial 9 and then a local phone number, it bounces between the dial tone and silence and the *error* light on the Adtran blinks. zaptel.conf span=1,0,0,esf,b8zs fxsks=1-8 loadzone=us defaultzone=us zapata.conf [channels] context=from-sip signalling=fxs_ks

Hello, I new to this, but with the help of mailing lists archives and IRC I am able to build my PBX. Thanks to all who had help me to reach till here. I am stuck at a point where I can't find the solution on mailing lists or even on IRC. I have individual 4 DID (Direct Inward Line) coming from Telco and terminating into TA 750 to FXS card. Many of them told that Phone instrument terminates

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.298 / Virus Database: 265.6.4 - Release Date: 12/22/2004

>>TURN OFF HTML!!!!!!!!!!! >>Why the hell do you feel I need to read your text in a lightish blue >>color???????? Do you know how shitty that looks compared to everyone >>elses black on white. Blue doesn't offer the contrast my eyes prefer. So >>why the hell do you feel important enough to override my defaults? You >>sir are the annoying guest who comes in

Hi All. I'm working on an * configuration. We require 8 inbound POTS lines, and CT1 or PRI seems like it will be quite expensive at that level. I've read that a T1 Channelbank plus the T100P would be a (the?) way to go for this situation. What is the recommended channelbank for use in this scenario? From searching the archives I see a lot of suggestions to get "a

Should FAX transmission generally work through Asterisk and a TDM400P connected through a PSTN gateway? At first blush I'd think that if they're all g.711uLaw encoded that it would work. But experience shows otherwise. Is there a better way to do FAX? -brian