similar to: T1 configuration, getting help via IRC?

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

I've put a t100p in our * server and I'm having trouble configuring it. It is directly connected to an Adtran TA 750 channel bank with two FXO cards (8 analog incoming lines total). I'm able to insmod and modprobe both zaptel and wct1xxp with no trouble, but when I start * with /usb/sbin/asterisk -c I get the following output: [root@rosella root]# /usr/sbin/asterisk -c Asterisk

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Hey all, I've setup * to serve the needs of our small helpdesk and I'm looking to expand. We're planning on doing support for different companies, each one identified by a different 1-800 number that terminates at our PBX. What I would like to know is: is there a variable I can read to determine what number any given caller dialed? I'd like to be able to separate calls based on

All, I need help. I have an (actually 2) Adtran TA750's with 8 FXO ports. I get a terrible buzz on every FXO port. If I unplug the Adtran and put an analog phone on each incoming line, I have no buzz. I also have 2 Carrier Access Access Bank I's with 12 FXO ports. When I plug the same analog lines into either one of those, no noise or buzz whatsoever. I went so far as to move the TA750

I recently set up Asterisk with an Adtran TA750. All is well except the phones do not show the MWI. I have configured zapata.conf properly, as all phones will receive a stutter dial tone if there is a message waiting in it's assigned mailbox. Does anybody know how I might fix this problem? Thank you for your time __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free,

Folks, I recently obtained a Western Electric multi-line phone and am seeking help with getting this beast working with *. The interesting stuff in my * implementation consists of a T100P card, a TDM400P card, and an Adtran TA750 channel bank with three quad-port FXS modules and a quad-port FXO. The TA750 is wired to a 24-port Cat 5 patch panel via a 25-pair Amp cable. The phone is a model

Hello. I have been going thru the wiki and asterisk related sites and have not been able to find any documentation about how to configure an Adtran TA750 channel bank. The remote disconnect supervision doesn't seem to be working, when the remote caller hangs up asterisk takes up to 30-45 seconds to hangup the call. Can somebody help? Thank's

All, Thanks for taking time to read. I am wanting someone to tell me that I have a clue here and that the following proposed setup would (possibly) work. Currently existing are 4 pots lines with qty. 10 AT&T 954/854 phones. Would like to convert to asterisk and at the same time do a mild feature upgrade. Proposing to get: PIII 800MHz or better >=256MB RAM

I'm trying to figure out how to start *..... Rh7.3,CVS,TE410P,TA750 If I just try the way the docs spell it out "/usr/sbin/asterisk -vvvc" it fails...... /var/log/asterisk/messages Oct 3 22:23:34 WARNING[1024]: File chan_zap.c, Line 610 (zt_open): Unable to open '/dev/zap/channel': No such device Oct 3 22:23:34 ERROR[1024]: File chan_zap.c, Line 4930 (mkintf): Unable

I get seg. fault with my * box. at the crash time i had about 35 Bridged Channel. i have: - dual xeon box (3.2Ghz) - 2Gb of memory - E7501 chipset motherboard. - U320 scsi disks - intel Gb ethernet device. - i only use sip for clients (no fxs in box) - TE405P for fxo (with 4 atran TA750). - ulaw is used as codec and echo cancellationo is enabled. but the core dump file has nothing to show with

Hello, I need help in creating a simple PSTN Gateway. This is the scenario: -I have one client sending me VoIP traffic (they don't have asterisk, so IAX is out of the picture for me) and I need to validate that traffic (only accept calls coming from his IP). After that I would terminate the calls to the PSTN network and keep logs for billing purposes. -I have a TE405P board and

Can anyone share any advice / documentation on how to configure a Tellabs 2572 T1 echo canceller? I connected one between a T100P and an Adtran TA750 FXO/FXS channelbank, but when echo cancellation is active I get a LOT of snap-crackle-pop (and other problems) on the line. The 2572 has a bunch of configuration options and they're impossible to guess without documentation, which I cannot find

Hello, I have been researching Echo Can's for a while now, and wanted to post this out to the list to solicit feedback (and if my assumptions are correct, hopefully help others out)... If anyone out there knows anything about wiring up an Echo Can, and my outline below is incorrect, please let the me/list know.. I have posted the Documents I received from Tellabs at:

Rich, Thanks a bunch, totally understand now and that actually makes total sense. (no need for schematics). This also explains why I used an TA750 to go into a Nortel MICS system, using FXO and no buzz. Totally balanced load from the analog ports on the Nortel across the 5 feet of CAT5 to the FXO on the adtran. Now I need to get rid of some Adtrans --- Anyone lookin to buy? :) Thanks

> I read your excellent post on the subject. I too am hearing the 60 Hz > hum on the FXO ports of my TA750. One Interesting thing is that it > goes away if there's an analog phone on the same POTS line, and you go > off-hook on it. I guess the analog phone has the repeat coils built > into it, and they balance the line for the FXO port. That's exactly correct; the

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

I believe it is not fiber, but I am not sure. I am going to take one of them home tonight and hook it to my POTS line there, which for sure is not fiber. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Michael Welter Sent:

Hello, We have a high volume of incoming and outgoing calls that come in via our analog POTS lines connected to FXO cards in an Adtran TA750. This is connected to a T100P. We are using Polycom IP 500's. The problem we are experiencing is, on frequent occasions, when someone dials out, there is another person who has just dialed in. I have had this problem at my house before (without an *

Does anyone keep a known telemarketer caller id database? If not has anyone proposed an Asterisk community project to share this information? Sort of a nation wide blacklist so Asterisk'ers can cut down on the garbage calls... -------------- next part -------------- An HTML attachment was scrubbed... URL: